summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* Switched davinci_emac Ethernet driver to use newer APIBen Warren2009-06-15-0/+4
| | | | | | | | Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* 85xx: Add UEC6 and UEC8 at SGMII mode for MPC8569MDSHaiying Wang2009-06-12-0/+25
| | | | | | | | | On MPC8569MDS board, UCC6 and UCC8 can be configured to work at SGMII mode via UEM on PB board. Since MPC8569 supports up to 4 Gigabit Ethernet ports, we disable UEC6 and UEC8 by default. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add RMII support for MPC8569MDSHaiying Wang2009-06-12-4/+34
| | | | | | | | | This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to enalbe_mpc8569mds_qe_uec which is more accurate. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add UEC3 and UEC4 support for MPC8569MDSHaiying Wang2009-06-12-0/+23
| | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add P2020DS supportSrikanth Srinivasan2009-06-12-0/+741
| | | | | | | | | | | | | The patch adds support for P2020DS reference platform. DDR3 interface uses hard-coded initialization rather than SPD for now and was tested at 667Mhz. Some PIXIS register definitions and associated code sections need to be fixed. TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all tested under u-boot. Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc512x: MPC5121ADS: Add NAND supportStefan Roese2009-06-12-1/+21
| | | | | | | | | | This patch adds NAND support to the MPC5121ADS board. Please note that the image size increased since NAND support didn't fit in the current image size (256k). Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* mpc512x: Add esd gmbh mecp5123 board supportStefan Roese2009-06-12-0/+458
| | | | | | | MECP5123 is a MPC5121E based module by esd gmbh. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* 74xx_7xx: CPCI750: Add CPCI adapter/target supportStefan Roese2009-06-12-0/+2
| | | | | | | | The CPCI750 can be built as CPCI host or adapter/target board. This patch adds support for runtime detection of those variants. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* 74xx_7xx: CPCI750: Add commandline editing/historyStefan Roese2009-06-12-1/+2
| | | | | Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* mpc85xx: 8536ds: Add USB related CONFIGsVivek Mahajan2009-06-12-2/+12
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8536ds and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc83xx: 8315erdb: Add USB related CONFIGsVivek Mahajan2009-06-12-1/+10
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8315erdb and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]xPeter Tyser2009-06-12-13/+13
| | | | | | | | Use the standard lowercase "x" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xxPeter Tyser2009-06-12-14/+14
| | | | | | | | Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC512x: add support for ARIA boardWolfgang Denk2009-06-12-0/+554
| | | | | | | ARIA is a MPC5121E based COM Express module by Dave/DENX. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* MPC512x: remove include/mpc512x.hWolfgang Denk2009-06-12-3/+3
| | | | | | | | | | | | | | | | | | | | Move needed definitions (register descriptions etc.) from include/mpc512x.h into include/asm-ppc/immap_512x.h. Instead of using a #define'd register offset, use a function that provides the PATA controller's base address. All the rest of include/mpc512x.h are register offset definitions which can be eliminated by proper use of C structures. There are only a few register offsets remaining that are needed in cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h which is intended as a temporary workaround only. In a later patch this file will be removed, too, and then auto-generated from the respective C structs. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* Rename ads5121 board into mpc5121adsWolfgang Denk2009-06-12-12/+12
| | | | | | | | | We rename the board so we use a consistent name in U-Boot and in Linux. Also, we use this opportunity to move the board into the Freecale vendor directory. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* Add support for Linux-like kallsysmsMike Frysinger2009-06-12-1/+1
| | | | | | | The kernel stores address<->symbol names in it so things can be decoded at runtime. Do it in U-Boot, and we get nice symbol decoding when crashing. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* mtd: MTD related config header changes (mtdparts command)Stefan Roese2009-06-12-0/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | By changing the cmd_mtdparts to only use the MTD infrastructure and not the direct interface to the CFI NOR FLASH driver we now need to add the MTD infrastructure to all boards using those mtdparts commands. This patch adds those components: CONFIG_MTD_DEVICE (for all FLASH types) plus CONFIG_FLASH_CFI_MTD (for NOR FLASH) To all board maintainers: Please test this on your platforms and report any problems/issues found. Thanks. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Ron Madrid <info@sheldoninst.com> Cc: Georg Schardt <schardt@team-ctech.de> Cc: Michal Simek <monstr@monstr.eu> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Martin Krause <martin.krause@tqs.de> Cc: Gary Jennejohn <garyj@denx.de> Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
* ZOOM2 Define GPIO banks used.Tom Rix2009-06-12-0/+8
| | | | | | | Enable the function and interface clocks for banks 2,3,5 and 6. Signed-off-by: Tom Rix <Tom.Rix@windriver.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
* at91: move cpu info print to cpuJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: move cpu name define to arm/arch/ cpu headerJean-Christophe PLAGNIOL-VILLARD2009-06-12-8/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* OMAP3: Zoom2: Enable Board and CPU infoDirk Behme2009-06-12-0/+6
| | | | | | | | | With other OMAP3 boards we recently switched to CPU and Board info API. From parallel merge, this is missing for Zoom2. Enable it for Zoom2, too. Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Acked-by: Tom Rix <Tom.Rix@windriver.com>
* ZOOM2 Add led support.Tom Rix2009-06-12-0/+16
| | | | | | This patch controls the large LED on the top left of the zoom2. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* ZOOM2 Add serial support.Tom Rix2009-06-12-13/+13
| | | | | | | | | | | | | | | | | | Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board. The default serial is from the USB connector on left side of the debug board. The USB connector will produce 2 of the 4 UARTS. On your host pick the first enumeration. The details of the setting of the serial gpmc setup are not available. The values were provided by another party. The serial port set up is the same with Zoom1. Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow. The kernel bootargs are console=ttyS3,115200n8 Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* lh7a40x: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* pxa: move serial driver to drivers/serialJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+15
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: remove cpu_initJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+1
| | | | | | move s3c44b0 to arch_cpu_init and as noone use cpu_init remove it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* TQM834x: use buffered writes to accelerate writing to flashWolfgang Denk2009-06-12-4/+3
| | | | | | | Also enable display of 'E'mpty sectors in "flinfo" output. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* TQM834x: add FDT supportWolfgang Denk2009-06-12-20/+39
| | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* TQM834x: fix environment size; add redundant env.Wolfgang Denk2009-06-12-14/+12
| | | | | | | Also reserve more space for U-Boot as it will probably grow soon. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* dm355 evm supportDavid Brownell2009-06-12-0/+190
| | | | | | | | | | | | | | | | | | | | | Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller: http://c6000.spectrumdigital.com/evmdm355/revd/ Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling: http://focus.ti.com/docs/prod/folders/print/tms320dm355.html This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* OMAP3EVM: Set default bootfileSanjeev Premi2009-06-12-0/+2
| | | | | | | | | | | | | | | | | | | The current configuration doesn't define default bootfile; leading to this warning at execution: OMAP3_EVM # dhcp ... ... DHCP client bound to address 192.168.1.11 *** Warning: no boot file name; using 'AC18BE16.img' TFTP from server 0.0.0.0; our IP address is 192.168.1.11; sending through gateway 192.168.1.1 Filename 'AC18BE16.img'. Load address: 0x82000000 Loading: * TFTP error: 'File not found' (1) Signed-off-by: Sanjeev Premi <premi@ti.com>
* ZOOM2 Add initial support for Zoom2Tom Rix2009-06-12-0/+226
| | | | | | | | | | | | | | | | | | | | | Zoom2 is a new board from Texas Instruments and LogicPD The logicpd web site is a good source for general information on this board. Please start looking here if the below links are broken. http://www.logicpd.com This is a pdf of the product http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf This is the product description web page http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp This patch provides a zoom2 base target by copying zoom1 and by making some obvious changes. To configure, run make omap3_zoom2_config Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* davinci dm6446evm NAND updateDavid Brownell2009-06-12-0/+7
| | | | | | | | | | | | | | | | This updates the optional (non-default!) NAND support for the DaVinci DM6446 EVM: - include MTD partitioning, defaulting to what Linux uses - use a flash-based BBT, which among other things speeds bootup This matches code that's now queued for mainline Linux, and might even merge in an upcoming 2.6.30-rc; and the MTIDS are set up so that the U-Boot $mtdparts environment variable can be passed as-is on the kernel command line as a cmdlinepart override. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: display correct clock infoDavid Brownell2009-06-12-2/+5
| | | | | | | | | | | | Move the clock-rate dumping code into the cpu/.../davinci area where it should have been, enabled by CONFIG_DISPLAY_CPUINFO, updating the format and showing the DSP clock (where relevant). Switch boards to use the cpuinfo() hook for this stuff. Remove a few now-obsolete PLL #defines. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ZOOM1 Remove more legacy NAND defines.Tom Rix2009-06-12-13/+0
| | | | | | These legacy NAND defines are no longer needed by this target. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* arm: timer and interrupt init reworkJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+2
| | | | | | | | | | | | | | actually the timer init use the interrupt_init as init callback which make the interrupt and timer implementation difficult to follow so now rename it as int timer_init(void) and use interrupt_init for interrupt btw also remane the corresponding file to the functionnality implemented as ixp arch implement two timer - one based on interrupt - so all the timer related code is moved to timer.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: cleanup remaining CONFIG_INIT_CRITICALJean-Christophe PLAGNIOL-VILLARD2009-06-12-7/+3
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: split out some dm644x-specific bits from pscDavid Brownell2009-06-12-0/+4
| | | | | | | | | | | | | | Split out DaVinci DM6446-specific bits from more generic bits: - Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips; DM6443 and DM6441 chips differ in available peripherals. - Move most DM644X-specific bits from psc.c to a new dm644x.c file, which is conditionally built. It provides device-specific setup. Plus minor coding style and comment updates with respect to the PSC. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ppc4xx: Add Sequoia RAM-booting targetStefan Roese2009-06-12-7/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds another build target for the AMCC Sequoia PPC440EPx eval board. This RAM-booting version is targeted for boards without NOR FLASH (NAND booting) which need a possibility to initially program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000) configured to setup the SDRAM, this debugger can load this RAM- booting image to the target address in SDRAM (in this case 0x1000000) and start it there. Then U-Boot's standard NAND commands can be used to program the NAND FLASH (e.g. "nand write ..."). Here the commands to load and start this image from the BDI2000: 440EPX>reset halt 440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin 440EPX>go 0x1000000 Please note that this image automatically scans for an already initialized SDRAM TLB (detected by EPN=0). This TLB will not be cleared. This TLB doesn't need to be TLB #0, this RAM-booting version will detect it and preserve it. So booting via BDI2000 will work and booting with a complete different TLB init via U-Boot works as well. Signed-off-by: Stefan Roese <sr@denx.de>
* Enable CONFIG_NET_MULTI on all remaining PPC4xx boardsBen Warren2009-06-12-1/+18
| | | | | | | All in-tree PPC4xx boards now use CONFIG_NET_MULTI Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
* 4xx: Remove binary cpld bitstream from DP405 boardMatthias Fuchs2009-06-12-80/+6
| | | | | | | | | | | | | This patch removes the cpld binary bitstream that is used by esd's cpld command on DP405 boards. Because u-boot with an external cpld bitstream may not take more space in flash than before the u-boot binary is shrinked a little bit. Some unused featues have been removed therefore. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* 4xx: Remove binary cpld bitstream from VOM405 boardMatthias Fuchs2009-06-12-16/+5
| | | | | | | | | | | | This patch removes the cpld binary bitstream that is used by esd's cpld command on VOM405 boards. Because u-boot with an external cpld bitstream may not take more space in flash than before the u-boot binary is shrinked a little bit. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* 4xx: Remove binary cpld bitstream from PMC405 boardMatthias Fuchs2009-06-12-3/+0
| | | | | | | | This patch removes the cpld binary bitstream that is used by esd's cpld command on PMC405 boards. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* 4xx: Remove binary cpld bitstream from CMS700 boardMatthias Fuchs2009-06-12-48/+5
| | | | | | | | | | | | | This patch removes the cpld binary bitstream that is used by esd's cpld command on CMS700 boards. Because u-boot with an external cpld bitstream may not take more space in flash than before the u-boot binary is shrinked a little bit. Some unused featues have been removed therefore. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
* i2c: Update references to individual i2c commandsPeter Tyser2009-06-12-5/+5
| | | | | | | | The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop, and isdram are no longer available so all references to them have been updated to the new form of "i2c <cmd>". Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* i2c: Remove deprecated individual i2c commandsPeter Tyser2009-06-12-23/+0
| | | | | | | | | | | | | The following individual I2C commands have been removed: imd, imm, inm, imw, icrc32, iprobe, iloop, isdram. The functionality of the individual commands is still available via the 'i2c' command. This change only has an impact on those boards which did not have CONFIG_I2C_CMD_TREE defined. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* mpc7448hpc2: Add CONFIG_SYS_I2C_SPEED definePeter Tyser2009-06-12-0/+1
| | | | | | | | | Add standard CONFIG_SYS_I2C_SPEED define for the mpc7448hpc2 so that it can use the common 'i2c speed' command. Note that the I2C controller utilized by the mpc7448hpc2 has a fixed speed and cannot be changed dynamically. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* 85xx: Add PIB support at CS4/CS5 for MPC8569MDSHaiying Wang2009-06-12-1/+9
| | | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Yu Liu <Yu.Liu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Fix some settings for MPC8569MDS boardHaiying Wang2009-06-12-3/+3
| | | | | | | | | | - Increase the size of malloc to 512KB because MPC8569MDS needs more memory for malloc to support up to eight Ethernet interfaces. - Move Environment address out of uboot thus the saved environment variables will not be erased after u-boot is re-programmed. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-08-27 09:39:41 +0000