summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* MLK-11767:imx: Modify the u-boot ENV offset for NAND storageYe.Li2015-10-27-7/+7
| | | | | | | | The current 36M offset will conflict with NAND FCB firmware2 when the nand chip block is 1MB size. This patch change it to 36M + 1M offset, so the redundant u-boot at firmware2 will not be broken. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11706: imx6sx: SabreSD: Expand malloc pool to 32MSandor Yu2015-10-16-1/+1
| | | | | | | | | | | Same issue as ENGR00321137, commit 3695635. GIS module need total 3M+3M+1.5M+1.5M=9M video memory. and sys reserved 16M memory for malloc. When gis module enabled, malloc may failed to allocate memory for other modules, that may cause system hang. Expand malloc pool to 32M. Signed-off-by: Sandor Yu <R01008@freescale.com>
* MLK-11718-3: imx: change the NAND env setting addressHan Xu2015-10-15-8/+8
| | | | | | | | The previous 8M address for NAND env might conflict with other boot parameters as the NAND block size increasing, change it to 36M to avoid it. Signed-off-by: Han Xu <b45815@freescale.com>
* MLK-11662-1 imx: mx6ul: Change 14x14 LPDDR2 ARM2 memory size to 256MBYe.Li2015-09-30-1/+9
| | | | | | | The actual memory size is 256MB not 512MB, otherwise it has a wrap problem in memory and will cause memtester failed. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11554 imx: mx6ulevk: Modify the mtest memory end to half of PHYS_SDRAM_SIZEYe.Li2015-09-16-1/+1
| | | | | | | Since the mx6ul 9x9 evk has different DDR size with 14x14 evk, change to use the half of PHYS_SDRAM_SIZE for mtest end. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11548 imx: imx6qp: add SabreSD board supportAnson Huang2015-09-15-1/+4
| | | | | | Add i.MX6QP SabreSD board support. Signed-off-by: Anson Huang <b20788@freescale.com>
* MLK-11528 imx: mx6ul check fuse before init beePeng Fan2015-09-10-0/+3
| | | | | | | | | | | Need to check fuse bit 25 of bank 0 word 4 before initialize bee. The bit: 0 means bee enabled, 1 means bee disabled. If disabled, continuing initialize bee will cause system hang, so need to check this bit before initialize bee. Add macro to enable BEE in header file, default disabled. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11461 imx: imx6ul: enable LDO bypass for 9x9 EVK boardAnson Huang2015-09-01-1/+3
| | | | | | | i.MX6UL-9x9-EVK board has PFUZE3000, so enable LDO bypass support for this board. Signed-off-by: Anson Huang <b20788@freescale.com>
* MLK-11408-2 imx: mx7d: Isolate 26 IP resources to domain 0 for A coreYe.Li2015-08-25-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | In current design, if any peripheral was assigned to both A7 and M4, it will receive ipg_stop or ipg_wait when any of the 2 platforms enter low power mode. We will have a risk that, if A7 enter wait, M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait asserted same time. There are 26 peripherals impacted by this IC issue: SIM2(sim2/emvsim2) SIM1(sim1/emvsim1) UART1/UART2/UART3/UART4/UART5/UART6/UART7 SAI1/SAI2/SAI3 WDOG1/WDOG2/WDOG3/WDOG4 GPT1/GPT2/GPT3/GPT4 PWM1/PWM2/PWM3/PWM4 ENET1/ENET2 Software Workaround: The solution is set M4 to a different domain with A core. So the peripherals are not shared by them. This way requires the uboot implemented the RDC driver and set the 26 IPs above to domain 0 only. CM4 image will set the M4 to domain 1 only. This patch enables the CONFIG_MXC_RDC for mx7d SABRESD board and ARM2 boards, and setup the 26 IP resources to domain 0. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11388 imx: mx7d: add support for mx7d 19x19 lpddr2 arm2 boardYe.Li2015-08-20-0/+4
| | | | | | | | | | This mx7d 19x19 lpddr2 arm2 board is based on 19x19 lpddr3 arm2 board with DDR changed to 512M LPDDR2. We added DDR script for LPDDR2 and a new u-boot build target: mx7d_19x19_lpddr2_arm2_config LPDDR2 script source: lpddr2_0_1.ds Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11367 imx: mx6ul: Add cma bootargs for 6ul 9x9 boardYe.Li2015-08-17-0/+6
| | | | | | | | | | | Since the i.MX6ul 9x9 evk board only has 256MB LPDDR2, while the CMA size used in kernel configuration is 320MB, so we have to set another value for the 9x9 evk board. This patch sets the cma=96M bootargs to in uboot. So the kernel will overwrite to use the new value. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11364 imx: mx6ul : Add support for i.MX6UL 9x9 EVK boardYe.Li2015-08-17-1/+14
| | | | | | | | | | | | | | The i.mx6ul 9x9 EVK shares the same base board with 6ul 14x14 EVK with two main changes on CPU board: 1. Change to use pfuze 3000. 2. Use 256MB LPDDR2 memory. This patch uses a macro CONFIG_6UL_9X9_LPDDR2 to distinguish the changes above, basing on 14x14 EVK board level codes. The new build target for the 9x9 EVK: mx6ul_9x9_evk_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11281-2 ARM: imx7d: enable plug in mode by default for lpsr modeAnson Huang2015-08-05-0/+1
| | | | | | | | | | As we need to support LPSR mode resume and due to hardware design requirement, DCD can NOT put DRAM exit from retention mode, so only plug in mode can do that to support LPSR mode, so enabled plug in mode by default for imx7d 12x12-lpddr3-arm2 board. Signed-off-by: Anson Huang <b20788@freescale.com>
* MLK-11228-3 android: Add "data" partition in fastbootYe.Li2015-07-13-0/+6
| | | | | | | | | Enable fastboot command "fastboot flash data" Custom may need to update data partition in fastboot mode. This patch enable flash data partition in emmc\sd. Signed-off-by: Zhang Sanshan <b51434@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11228-1 android: Integrate community fastboot with FSL i.MX fastbootYe.Li2015-07-13-175/+157
| | | | | | | | | | | | | | | | | | | | | 1. Replace the UDC driver with community's USB gadget d_dnl driver. 2. Integrate the FSL SD/SATA/NAND flash operations, since the GPT and EFI partitions are not support by i.MX. 3. Add FDT support to community's android image. 4. Change the booti command to boota, due to the booti has been used for ARM64 image boot. 5. Modify boota implementation to load ramdisk and fdt to their loading addresses specified in boot.img header, while bootm won't do it for android image. 6. Modify the android image HAB implementation. Authenticate the boot.img on the "load_addr" for both SD and NAND. 7. Enable new configuration CONFIG_FSL_FASTBOOT for Freescale's fastboot with relevant header file "fsl_fastboot.h". While disabling the configuration, the community fastboot is used. 8. Use community's way to combine cmdline in boot.img and u-boot environment, not overwrite the cmdline in boot.img Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11227 imx: mx6ul_14x14_lpddr2_arm2 add weimnor defconfigPeng Fan2015-07-09-5/+18
| | | | | | | | | | | | | 1. Add weimnor boot defconfig 2. move CONFIG_FSL_USDHC and CONFIG_VIDEO to board header 3. Add CONFIG_SYS_FLASH_PROTECTION for mx6ul 14x14 lpddr2 arm2 4. correct CONFIG_SYS_FLASH_SECT_SIZE and CONFIG_SYS_MAX_FLASH_SECT 5. Add comments for setup_eimnor, since ENET2_RXER pin conflicts with ENET2. Also eimnor support will disable SD1/SD2, need ENET to boot kernel and nfs using enet. So setup_eimnor should be invoked after setup_fec Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11135-2 imx: mx6ul: Add MX6UL LPDDR2 ARM2 board supportYe.Li2015-06-19-0/+69
| | | | | | | | | Add MX6UL LPDDR2 ARM2 board BSP codes, supported peripherals: SD1, eMMC(USDHC2), USB OTG1, I2C, ENET2, PMIC. Due to a board issue, the SD1 only supports 1 bit bus width. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11135-1 imx: mx6ul: Abstract the common settings of 6UL ARM2 boardYe.Li2015-06-19-392/+407
| | | | | | | Create a new head file mx6ul_arm2.h, and move the common settings of MX6UL ARM2 boards to this file. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11134-2 imx: mx7d_12x12_ddr3_arm2 update spi nor codePeng Fan2015-06-19-1/+1
| | | | | | | We should use board_spi_cs_gpio and remove the GPIO from CONFIG_SF_DEFAULT_CS. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11134-1 imx: mx6ul_14x14_ddr3_arm2 correct CONFIG_DEFAULT_SPI_CSPeng Fan2015-06-19-1/+1
| | | | | | We should not put the GPIO in CONFIG_SF_DEFAULT_CS Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11059 imx: HAB unable to support Encrypted boot for 4096-bit keysUlises Cardenas2015-06-16-0/+60
| | | | | | | | Abstracted the CSF size in imximage from a hardcoded value to a config setting CONFIG_CSF_SIZE. This configuration is only enabled for secure boot. Increased the size of the CSF default allocation to 0x4000. This size covers the event the worst case of 4906-bits keys.
* MLK-11062 imx: mx7d arm2: Add nand mtdpart info to u-boot environmentsYe.Li2015-06-08-0/+22
| | | | | | For nand boot, the mtdpart info are needs to load kernel and rootfs. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-11010 imx: mx7d: Fix EIMNOR lock issue on mx7d 19x19 lpddr3 boardYe.Li2015-06-01-0/+3
| | | | | | | | | | Since the flash blocks are locked at default , need to set "CONFIG_SYS_FLASH_PROTECTION" to unlock them before write/erase. The patch also add the pinmux for LBA (ADV) pin and set eimnor enabled at default. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10956 imx: mx6ul: Change BSP name and dtb name for 14x14 packageYe.Li2015-05-25-9/+9
| | | | | | | | | | | | | | Since there is another 9x9 package for mx6ul, modify the BSP names of ddr3 arm2 board and evk board to add 14x14 package info. Also modify the loaded dtb file to align with kernel. After the change, the build target for mx6ul ddr3 arm2 board is: mx6ul_14x14_ddr3_arm2_config and the build target for mx6ul evk board is: mx6ul_14x14_evk_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10955 imx: mx7d arm2: Add NAND support for mx7d 19x19 lpddr3 arm2 boardYe.Li2015-05-25-0/+21
| | | | | | | | Add the default TSOP NAND support and build target. New build target for nand boot: mx7d_19x19_lpddr3_arm2_nand_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10839: arm: imx: mx7d 19x19 lpddr3 arm2 board supportAdrian Alonso2015-05-13-2/+85
| | | | | | | | | | | | | * Add mx7d_19x19_lpddr3_arm2 target board supprt * Enable i2c, spinor, usb, usdhc, qspi, enet, uart * Build targets mx7d_19x19_lpddr3_arm2_defconfig mx7d_19x19_lpddr3_arm2_eimnor_defconfig - Set EIMNOR settings for Intel Sibley Asynchronous mode - Set flash sector size for 256kb (erase block size) Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10873-1 imx:mx7d use pmic frameworkPeng Fan2015-05-11-11/+8
| | | | | | Use pmic framework to simplify code and make code clean. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10865 imx: mx6ulevk: Add android supportYe.Li2015-05-08-0/+67
| | | | | | | | Add android features booti, fastboot and recovery to i.MX6UL EVK board. Since there is no user button on the board, we can't implement the recovery by using button. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10852 imx: mx6ul_ddr3_arm2: Add support for NAND bootYe.Li2015-05-07-20/+20
| | | | | | | | | | | Since the NAND has two pins conflict with SD2, when NAND is enabled, we must disable SD2. So the CONFIG_SYS_FSL_USDHC_NUM needs configure to 1 and should be moved to under defining CONFIG_SYS_USE_NAND. New build target for NAND boot: mx6ul_ddr3_arm2_nand_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10841 imx: mx6ul_ddr3_arm2: Add support for WEIMNOR bootYe.Li2015-05-07-1/+6
| | | | | | | | | | Correct the EIMNOR settings to non-mux mode and set the environment variables configuration to FLASH when using WEIMNOR boot. New target is added for build WEIMNOR boot u-boot: mx6ul_ddr3_arm2_eimnor_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10829-2 imx:mx6 support thermal for all mx6Peng Fan2015-05-06-14/+10
| | | | | | | | Move CONFIG_IMX_THERMAL to mx6_common.h Make CONFIG_MXC_OCOTP only depends on CONFIG_CMD_FUSE, since when THERMAL is not implemented, we may use fuse. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10817 imx:mx6ul_ddr3_arm2 add mx6ul ddr3 arm2 board supportPeng Fan2015-05-05-0/+428
| | | | | | | | | | | | | Add board code for mx6ul ddr3 arm2 board. QSPI, USDHC, ENET, USB, VIDEO, SPINOR, EIMNOR Add sd1, qspi and spinor boot support DDR script is 1.02 version. Signed-off-by: Fugang Duan <b38611@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10821 imx: mx6ulevk: Add board support for mx6ulevkYe.Li2015-05-05-0/+395
| | | | | | | | | | | Add BSP codes to support modules on the board: I2C, SD/eMMC, NAND, QSPI, FEC1/FEC2, USB, LCDIF, 74LV, Serial DDR version: 1.0 Build target: mx6ulevk_config mx6ulevk_qspi1_config Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10808-4 imx: Move system counter driver to imx-commonYe.Li2015-05-04-2/+10
| | | | | | | | | | | | | Since the system counter driver will also be used by mx6ul, move this timer driver to imx-common and rename it as syscounter.c For mx6ul and mx7, configurations are used for choose the GPT timer or system counter timer (default). GPT timer: CONFIG_GPT_TIMER System counter timer: CONFIG_SYSCOUNTER_TIMER Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10774-50 imx:mx7dsabresd move VIDEO config before EPDCPeng Fan2015-04-29-16/+16
| | | | | | Move VIDEO config to the front of EPDC Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-47 imx: mx7dsabresd enable thermalPeng Fan2015-04-29-0/+2
| | | | | | Enable thermal for mx7dsabresd board. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10522-3: imx: mx7d_12x12_ddr3_arm2: add target board supportAdrian Alonso2015-04-29-0/+56
| | | | | | | | | | | | | | * Add mx7d_12x12_ddr3_arm2 target board support * Initial support for mx7d_12x12_ddr3_arm2 target board add support for base hardware eMMC, SD and ECSPI boot. Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 51d69f7996cc6e6da8bb3f0af751549cb2435e44) Conflicts: boards.cfg
* MLK-10522-1: mx7d_arm: allow override mtest settingsAdrian Alonso2015-04-29-0/+2
| | | | | | | | | * Allow to override mtest settings for target board variants that differs on physical sdram memory size Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 6173a3954b83ce22e24c62bc8ee922007b0929a6)
* MLK-10576 ARM: i.MX6: exclude the ARM errata from i.MX6 UP systemNitin Garg2015-04-29-0/+3
| | | | | | | | | | | | | | | | The ARM errata 751472, 794072, 761320, 845369 only applied to the following configuration: This erratum affects configurations with either: - One processor if the ACP is present - Two or more processors i.MX6 family does not have the ACP and thus only the MPCore system will be impacted, which are the i.MX6DQ, i.MX6DL, and i.MX6QP. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> (cherry picked from commit 0db960784ba4f631ee5c0321b5d25f3b1ac55640)
* MLK-10524: iMX6x: Implement workaround for Cortex-A9 errata 845369Nitin Garg2015-04-29-0/+1
| | | | | | | | | | Under very rare timing circumstances, transitioning into streaming mode might create a data corruption. Present on Two or more processors or 1 core with ACP, all revisions. This erratum can be worked round by setting bit[22] of the undocumented Diagnostic Control Register to 1. Signed-off-by: Nitin Garg <nitin.garg@freescale.com> (cherry picked from commit 70ad44e523680de67dd8b7a7505d7f27799980ee)
* MLK-10520 add clk_ignore_unused in i.MX7d u-boot parameterHan Xu2015-04-29-0/+2
| | | | | | | add this parameter in u-boot as a temporary workaround. Signed-off-by: Han Xu <b45815@freescale.com> (cherry picked from commit f0beee980914360c8783406ef8694974467eb07b)
* MLK-10492-2 imx: mx7dsabresd: Add TFT43AB LCD supportYe.Li2015-04-29-1/+1
| | | | | | | | The mx7dsabresd uses new LCD TFT43AB which has 480 x 272 pixels. Update panel info for this LCD. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit e77d667b20956a37de9d367a8914ef2fe79258df)
* MLK-10477-5 imx: mx7dsabresd: Add EPDC supportYe.Li2015-04-29-28/+17
| | | | | | | | | | | | | | | | To enable the EPDC feature: 1. Uncomments CONFIG_SPLASH_SCREEN and CONFIG_MXC_EPDC settings in mx7dsabresd.h 2. cd <kernel_dir>/firmware/imx 3. python ihex2bin.py -i epdc_ED060XD4C1_TC.fw.ihex -o epdc_splash.bin 4. cp epdc_splash.bin to [FAT partition on SD card] Since the EPDC has pinmux conflicts with ENET and QSPI. These two modules can't work at same time. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 8ba7f88f9efac9f90319b71644d3d1191f535d03)
* MLK-10477-4 imx: mx7d 12x12 lpddr3 ARM2: Add EPDC supportYe.Li2015-04-29-2/+29
| | | | | | | | | | | | | To enable the EPDC feature: 1. Uncomments CONFIG_SPLASH_SCREEN and CONFIG_MXC_EPDC settings in mx7d_12x12_lpddr3_arm2.h 2. cd <kernel_dir>/firmware/imx 3. python ihex2bin.py -i epdc_ED060XD4C1_TC.fw.ihex -o epdc_splash.bin 4. cp epdc_splash.bin to [FAT partition on SD card] Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 414824dcb77a067213849d340cf92777e6546810)
* MLK-10478 mx6: EPDC: Improve EPDC usage and configurationYe.Li2015-04-29-27/+7
| | | | | | | | | | | | | | Change to load EPDC waveform from FAT partition and allocate waveform buffer, framebuffer and working buffer in dynamic manner not static. So many EPDC configurations are removed. To enable the EPDC feature, must define CONFIG_MXC_EPDC and CONFIG_SPLASH_SCREEN. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 4d55a4124be3a3a6288c3c845d17fd9d4f2b8b43) Conflicts: include/configs/mx6slevk.h
* MLK-10774-38 imx: fix ecspi codePeng Fan2015-04-29-5/+5
| | | | | | | | | | | This commit 155fa9af95ac5be857a7327e7a968a296e60d4c8 "spi: mxc: fix sf probe when using mxc_spi" introduces "board_spi_cs_gpio" function to discard gpio in CONFIG_SF_DEFAULT_CS for spi flash. Follow this rule to make imx boards work fine. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10448-7 imx:mx6qpsabreauto add missed macroPeng Fan2015-04-29-1/+4
| | | | | | Add CONFIG_DEFAULT_FDT_FILE macro and PHYS_SDRAM_SIZE. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10448-3 mx6: ccm: Change the clock settings for i.MX6QPYe.Li2015-04-29-0/+3
| | | | | | | | | | | | | | | | Since i.MX6QP changes some CCM registers, so modify the clocks settings to follow the hardware changes. A new CONFIG_MX6QP is introduced here and is used for the CCM difference. At default CONFIG_MX6Q is enabled along with the CONFIG_MX6QP. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 5e4d1537ce9a476c8404126350f05d8976c5aa35) Conflicts: arch/arm/cpu/armv7/mx6/clock.c arch/arm/include/asm/arch-mx6/crm_regs.h include/configs/mx6_common.h
* MLK-10774-35 imx:mx7 use power_init_boardPeng Fan2015-04-29-10/+9
| | | | | | | Upgrade to upstream way, using power_init_board. Add pfuze300 support. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10774-34 imx:mx7d android fix build errorPeng Fan2015-04-29-0/+2
| | | | | | Add CONFIG_CMD_FASTBOOT Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
generated by cgit v1.1 at 2024-06-28 15:11:42 +0000