summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* Merge branch 'next' of ../nextWolfgang Denk2010-12-22-45/+695
|\
| * p1022ds: enable reginfo commandMatthew McClintock2010-12-18-0/+1
| | | | | | | | | | | | | | Add reginfo as a default command for p1022ds boards Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * mpc52xx, charon: change mtd default partitionsHeiko Schocher2010-12-17-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | New default partitions on nor flash: 640k (firmware) 1408k (kernel) 2m (initrd) 4m (small-fs) 24320k (big-fs) 256k (dts) Signed-off-by: Heiko Schocher <hs@denx.de>
| * mpc5200, tqm5200: correct MTDIDS_DEFAULT to fit with name linux assignsHeiko Schocher2010-12-17-6/+6
| | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
| * xilinx-ppc4xx-generic: Use common u-boot.ldsRicardo Ribalda Delgado2010-12-17-0/+1
| | | | | | | | | | | | | | Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Update lwmon5 board supportStefan Roese2010-12-17-8/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch includes the following changes for the lwmon5 board support: - Enable cache in SDRAM - Use common EHCI driver instead of the PPC4xx specific OHCI driver This can be done since only high-speed devices are connected. - Remove cached TLB entry again after ECC setup - Use correct define for cache enabling (CONFIG_4xx_DCACHE instead of CONFIG_SYS_ENABLE_SDRAM_CACHE) - Enable FIT image support Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: t3corp: Add support for the Xilinx DS617 flash chipStefan Roese2010-12-17-6/+12
| | | | | | | | | | | | | | | | | | | | | | | | The t3corp board has an Xilinx DS617 flash chip connected to the onboard FPGA. This patch adds support for these chips. Board specific flash accessor functions are needed, since the chips can only be read correctly in 16bit mode. Additionally the FPGA chip-selects are configured for device-paced transfers (ready is enabled). Signed-off-by: Stefan Roese <sr@denx.de>
| * Armada100: Add Board Support for Marvell Aspenite-DBPrafulla Wadaskar2010-12-16-0/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with * Processor upto 1.2GHz * Parallel 1Gb x8 DDR2-1066 MHz * 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR * Footprints for eMMC/eSD NAND & MMC x8 card * 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket * SEAF memory board, subset of PISMO2 With Peripherals: * 4.3” WVGA 24-bit LCD * Audio codecs (AC97 & I2S), TSI * VGA camera * Video in via 3 RCA jacks, and HDMI type C out * Marvell 88W8688 802.11bg/BT module * GPS RF IC * Dual analog mics & speakers, headset jack, LED, ambient light sensor * USB2.0 HS host (A), OTG (micro AB) * FE PHY, PCIE Mini Card slot * GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR This patch adds basic board support with DRAM and UART functionality The patch is tested for boot from DRAM using XDB Signed-off-by: Mahavir Jain <mjain@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * mv-common.h: Add support for ARMADA100 PlatformsPrafulla Wadaskar2010-12-16-16/+50
| | | | | | | | | | | | | | This patch adds commonly used macros for ARMADA100 based baords, Also some code reshuffled and updated for typos and comments Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
| * Merge branch 'master' of ../master into nextWolfgang Denk2010-12-16-34/+434
| |\
| * | mpc52xx: add support for tqm52xx based board charonHeiko Schocher2010-12-16-9/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - serial console in PSC1 - 128MiB DRAM - 32MiB Flash - FEC Ethernet - 2 I2C busses - FPGA on CS3 - IDE - VGA SMI501 Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de>
| * | OMAP3: SPI driverDirk Behme2010-12-11-0/+2
| | | | | | | | | | | | | | | | | | CC: Ruslan N. Araslanov <byaaka@yandex.ru> Signed-off-by: Ruslan Araslanov <ruslan.araslanov@vitecmm.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | ARMV7: OMAP4: twl6030 add battery charging supportBalaji T K2010-12-11-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add battery charging support twl6030 driver. Add support for battery voltage and current measurements. Add command to get battery status and start/stop battery charging from USB. Signed-off-by: Balaji T K <balajitk@ti.com> Tested-by: Steve Sakoman <steve.sakoman@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | Move LDSCRIPT definitions to board config files.Wolfgang Denk2010-12-09-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recent cleanup actions resulted in a number of config.mk files that contained only LDSCRIPT definitions. Move these into th respective board config files and remove the now empty config.mk files. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Detlev Zundel <dzu@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de> Cc: Peter De Schrijver <p2@mind.be> Acked-by: Detlev Zundel < dzu@denx.de> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Heiko Schocher<hs@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
| * | Davinci: add support for the ea20 boardStefano Babic2010-12-09-0/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board uses the OMAP-L138 SOM stacked on a custom baseboard. It supports SPI Flash, Ethernet with RMII. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | da850: Add RMII support for EMACSudhakar Rajashekhara2010-12-09-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is a port of the work by Sudhakar Rajeshekhara in commit ab3effbcad8851cc65dc5241a01c064d2030a3b2 of git://arago-project.org/git/people/sandeep/u-boot-davinci.git. The da850 UI board has on it an RMII PHY which can be used if the MDC line to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by configuring the values of some GPIO pins on the IO expander of the UI board. This patch implements disabling that line via GPIO2[6], configuring the UI board's IO expander and setting only the pinmux settings that are needed for RMII operation. Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | Add board support for hawkboardSughosh Ganu2010-12-09-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds basic board support for TI's OMAP-L138 based Hawkboard. This board is pretty similar to the da850 EVM. Support for nand and network access is added in this version. The following bootup procedure is used. At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand controllers and copies the second stage bootloader(nand_spl) to RAM. The secondary bootloader then copies u-boot from a predefined location in the nand flash to the RAM, and passes control to the u-boot image. Three config options are supported * hawkboard_config - Used to create the u-boot.bin. Tftp the u-boot.bin image to the RAM from u-boot, and flash to the nand flash at address 0xe0000. * hawkboard_nand_config - Used to generate the secondary bootloader(nand_spl) image. This creates an elf file u-boot-spl under nand_spl/. Create an AIS signed image using this file, and flash it to the nand flash at address 0x20000. The ais file should fit in one block. * hawkboard_uart_config - This is same as the first image, but with the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | da850: Enable SPI FlashStefano Babic2010-12-09-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch was already posted to the arago project, but not yet to mainline. It allows to save environment into the spi flash. Tested on LogiPD tmdxl138. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Detlev Zundev <dzu@denx.de> CC: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-12-17-2/+2
|\ \ \
| * \ \ Merge branch 'for-upstream' of git://git.denx.de/u-boot-atmelWolfgang Denk2010-12-17-2/+2
| |\ \ \
| | * | | AT91: fix TOP9000 build problem and change CONFIG_SYS_TEXT_BASEReinhard Meyer2010-12-17-2/+2
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* | | | | Coding style (white space) cleanup.Wolfgang Denk2010-12-17-1/+0
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* | | | | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-12-17-19/+35
|\ \ \ \ \ | |/ / / / | | | | / | |_|_|/ |/| | |
| * | | DaVinci DM6467: Add ARM Relocation SupportSandeep Paulraj2010-12-17-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | Add ARM Relocation Support Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | DaVinci Schmoogie: Add ARM Relocation SupportSandeep Paulraj2010-12-17-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | Add ARM Relocation Support Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | DaVinci sffsdr: Add ARM Relocation SupportSandeep Paulraj2010-12-17-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | Add ARM Relocation Support Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | DaVinci Sonata: Add ARM Relocation SupportSandeep Paulraj2010-12-17-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | Add ARM Relocation Support Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
| * | | DaVinci: Config cleanupSandeep Paulraj2010-12-17-19/+0
| |/ / | | | | | | | | | | | | | | | | | | Some DaVinci boards are using flags that are no longer valid So remove them. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-12-16-0/+21
|\ \ \ | |/ /
| * | pm9261: enable cache commandAsen Dimov2010-12-16-0/+1
| | | | | | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * | pm9261: ARM relocation supportAsen Dimov2010-12-16-0/+6
| | | | | | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * | pm9263: enable cache commandAsen Dimov2010-12-16-0/+1
| | | | | | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * | pm9263: ARM relocation supportAsen Dimov2010-12-16-0/+6
| | | | | | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * | pm9g45: enable cache commandAsen Dimov2010-12-16-0/+1
| | | | | | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
| * | pm9g45: ARM relocation supportAsen Dimov2010-12-16-0/+6
| | | | | | | | | | | | Signed-off-by: Asen Dimov <dimov@ronetix.at>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-12-14-8/+11
|\ \ \ | |/ /
| * | DaVinci DM6446: Config UpdateSandeep Paulraj2010-12-11-8/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DM6446 does not build due to the ARM relocation patch. Also the board does not build in the NOR mode. Changed default to NAND to ensure no build failure. While at it removed CONFIG_CMD_KGDB Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* | | tsec: Revert to setting TBICR_ANEG_ENABLE by default for SGMIIKumar Gala2010-12-13-8/+20
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following commit: commit 46e91674fb4b6d06c6a4984c0b5ac7d9a16923f4 Author: Peter Tyser <ptyser@xes-inc.com> Date: Tue Nov 3 17:52:07 2009 -0600 tsec: Force TBI PHY to 1000Mbps full duplex in SGMII mode Removed setting Auto-Neg by default, however this is believed to be proper default configuration for initialization of the TBI interface. Instead we explicitly set CONFIG_TSEC_TBICR_SETTINGS for the XPedite5370 & XPedite5500 boards that use a Broadcomm PHY which require Auto-Neg to be disabled to function properly. This addresses a breakage on the P2020 DS & MPC8572 DS boards when used with an SGMII riser card. We also remove setting CONFIG_TSEC_TBICR_SETTINGS on the P1_P2_RDB family of boards as now the default setting is sufficient for them. Additionally, we clean up the code a bit to remove an unnecessary second define. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Peter Tyser <ptyser@xes-inc.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-imxWolfgang Denk2010-12-09-3/+4
|\ \
| * | mx51evk: savenv or env save command does not workJason Liu2010-11-21-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | fix saveenv or env save command not work on mx51evk board. with this patch, we can use savenv or env save to store enviroments to mmc card slot 0 Signed-off-by: Jason Liu <r64343@freescale.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-12-08-1/+331
|\ \ \
| * | | arm920t/at91/timer: replace bss variables by gdAndreas Bießmann2010-12-07-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc bss values in arm920t/at91/timer driver. The usage of bss values in driver before initialisation of bss is forbidden. In that special case some data in .rel.dyn gets corrupted by the arm920t/at91/timer driver. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | | at91rm9200ek: add configure target for RAM bootAndreas Bießmann2010-12-07-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch also removes now unnecessary config.mk in board directory and make usage of new features in boards.cfg. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | | at91rm9200ek: fix SDRAM initialistation valuesAndreas Bießmann2010-12-07-1/+1
| | | | | | | | | | | | | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | | AT91: add TOP9000 supportReinhard Meyer2010-12-07-0/+314
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the EMK TOP9000 CPU Module which is based on ATMELs ARM926EJS AT91SAM9XE SoC. Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* | | | Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk2010-12-06-1/+0
|\ \ \ \
| * | | | mpc512x: aria: cleanup board config fileAnatolij Gustschin2010-12-01-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_FSL_DIU_LOGO_BMP has been removed while refactoring MPC8610 and MPC5121 DIU code, so remove it. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | | | | powerpc/85xx: Enable HWCONFIG on MPC8572DSKumar Gala2010-12-01-0/+1
|/ / / / | | | | | | | | | | | | | | | | | | | | We need HWCONFIG to allow configuration of DDR params Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | | Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2010-11-30-1/+36
|\ \ \ \
| * \ \ \ Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-11-30-1/+36
| |\ \ \ \ | | |/ / /
generated by cgit v1.1 at 2024-11-09 06:29:52 +0000