summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* snowball: Adding architecture dependent initialisationMathieu J. Poirier2012-09-01-0/+1
| | | | | | | Enabling timers and clocks in PRCMU and cleaning up mailbox. Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: John Rigby <john.rigby@linaro.org>
* snowball: Add support for ux500 based snowball boardMathieu J. Poirier2012-09-01-0/+256
| | | | | | | | | | | Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: John Rigby <john.rigby@linaro.org> Acked-by: Tom Rini <trini@ti.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Conflicts: drivers/gpio/Makefile
* da8xx/hawkboard: Add support for ohci host controllerSughosh Ganu2012-09-01-1/+13
| | | | | | | | | | Also enable the ohci port on hawkboard. These additions result in an increased u-boot size -- adjust the same accordingly in the board's config. Move the usb header for da8xx platforms under arch-davinci. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
* omap4/5/am33xx: Make lowlevel_init available to all armv7 platformsTom Rini2012-09-01-12/+6
| | | | | | | | | | | | | | Make the lowlevel_init function that these platforms have which just sets up the stack and calls a C function available to all armv7 platforms. As part of this we change some of the macros that are used to be more clear. Previously (except for am335x evm) we had been setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we should have been doing this initially and do now. Cc: Sricharan R <r.sricharan@ti.com> Tested-by: Allen Martin <amartin@nvidia.com> Signed-off-by: Tom Rini <trini@ti.com>
* am335x evm: Enable support for spi0Tom Rini2012-09-01-0/+9
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* sc_sps_1: Adjust board config to use 'mxs' SoC codeOtavio Salvador2012-09-01-2/+2
| | | | | | | Fix build failure due the move of mx28 code to 'mxs' SoC. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
* MX28: Add SchulerControl SC_SPS_1 platformMarek Vasut2012-09-01-0/+208
| | | | | | | | | | | This i.MX28 platform supports the following: * 2x FEC ethernet * USB on USBH0 * I2C EEPROM * SPI NVRAM * LEDs Signed-off-by: Marek Vasut <marex@denx.de>
* vision2: do not overwrite the consoleFabio Estevam2012-09-01-0/+2
| | | | | | | On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx51evk: do not overwrite the consoleFabio Estevam2012-09-01-0/+2
| | | | | | | On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX5: mx53loco: do not overwrite the consoleStefano Babic2012-09-01-0/+2
| | | | | | | | | On this board, the console is always set to the serial line. Do not allow to overwrite it when video is enabled. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* mxs: reorganize source directory for easy sharing of code in i.MXS SoCsOtavio Salvador2012-09-01-6/+6
| | | | | | | | | Most code can be shared between i.MX23 and i.MX28 as both are from i.MXS family; this source directory structure makes easy to share code among them. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Stefano Babic <sbabic@denx.de>
* mx28evk: Turn on cachesFabio Estevam2012-09-01-2/+0
| | | | | | Turn on data and instruction caches. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* Add support for Bluegiga APX4 Development KitVeli-Pekka Peltola2012-09-01-0/+238
| | | | | | | | | | This adds support for Bluegiga APX4 Development Kit. It is built around Freescale i.MX28. Currently supported features are: ethernet, I2C, MMC, RTC and USB. APX4 has only one ethernet port. Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com> Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Cc: Stefano Babic <sbabic@denx.de>
* at91: Add support for taskit AT91SAM9G20 boards.Markus Hubig2012-09-01-0/+266
| | | | | | | | | | This adds support for the AT91SAM9G20 boards by taskit GmbH. Both boards, Stamp9G20 and PortuxG20, are integrated in one file. PortuxG20 is basically a SBC built around the Stamp9G20. Signed-off-by: Markus Hubig <mhubig@imko.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.deve@googlemail.com>
* arm : Atmel : add at91sam9x5ek board supportBo Shen2012-09-01-0/+183
| | | | | | | | | | | | Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: Bo Shen <voice.shen@atmel.com> [move MAINTAINERS entry to right place] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* am335x_evm: enable SMSC PHY driverIlya Yanok2012-09-01-0/+1
| | | | | | | | Beaglebone uses SMSC PHY which works incorrectly with generic PHY driver so enable SMSC PHY driver to fix networking problems on Beaglebone. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* dm: Move OMAP GPIO driver to drivers/gpio/Marek Vasut2012-09-01-0/+18
| | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* dm: Select CONFIG_SPL_GPIO_SUPPORT on OMAPMarek Vasut2012-09-01-0/+6
| | | | | | | | | | | | | This fixes the breakage with SPL on most OMAP boards after the GPIO driver was moved. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am33xx evm: Add CONFIG_CMD_EEPROM and relatedTom Rini2012-09-01-0/+4
| | | | | | | am33xx boards have at least one eeprom and in the case of beaglebones with capes, more. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Update config for common usageTom Rini2012-09-01-10/+60
| | | | | | | | | | - Add default commands - Add HUSH parser - Make environment, malloc areas larger - Add ATAGS and OF_LIBFDT - Add defaults to boot ramdisk and MMC, use uEnv.txt Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: igep00x0: add SPL support for IGEP-based boardsJavier Martinez Canillas2012-09-01-0/+65
| | | | | | | This patch adds SPL support for IGEP-based boards. Tested on an IGEPv2 Rev.C board with Micron NAND Flash memory. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
* OMAP3: igep00x0: Add config option to choose flash storage memoryJavier Martinez Canillas2012-09-01-0/+19
| | | | | | | | IGEP-based boards can have two different flash memories, a OneNAND or a NAND device. Add a configuration option for to choose which memory to use. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
* am335x_evm: CPSW supportChandan Nath2012-09-01-1/+19
| | | | | | | | | This patch adds board-specific initialization for CPSW on TI AM335X based boards. Tested on BeagleBone. Signed-off-by: Chandan Nath <chandan.nath@ti.com> [Ilya: split board-specific part into separate patch] Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* omap: am335x_evm: enable i2c1 channelSteve Sakoman2012-09-01-0/+1
| | | | | | | This patch sets up pinmux, enables fclk, and defines CONFIG_I2C_MULTI_BUS Signed-off-by: Steve Sakoman <steve@sakoman.com>
* beagle: fix termination of buddy env settingPeter Meerwald2012-09-01-1/+1
| | | | Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
* igep00x0: default mmcrootfstype to EXT4Javier Martinez Canillas2012-09-01-1/+1
| | | | | | | | | omap2plus_defconfig now has built-in compile support for EXT4 enabled by default now. So, we can use EXT4 as the default root file system type for MMC. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
* igep00x0: default to OMAP-specific serial driverJavier Martinez Canillas2012-09-01-1/+1
| | | | | | | | | An OMAP specific serial driver was merged on the Linux kenel a long time ago. So, it makes sense to default the console name to OMAP ttyO instead of the generic ttyS naming. Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org> Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
* da850/omap-l138: add support for direct NOR boot modeLad, Prabhakar2012-09-01-2/+20
| | | | | | | | | | | This patch adds support for direct NOR boot mode on da850/omap-l138. Added da850evm_direct_nor entry in boards.cfg to allow to build targets. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* da850/omap-l138: Add support for NAND SPLLad, Prabhakar2012-09-01-0/+26
| | | | | | | | | | This patch adds configuration required for NAND SP on DA850/OMAP-L138. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* da850/omap-l138: Add support to read u-boot image from MMC/SDLad, Prabhakar2012-09-01-0/+11
| | | | | | | | | | | | | | | DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will be in SPI flash and U-Boot image will be in MMC/SD card. SPL will do the low level initialization and then loads the u-boot image from MMC/SD card. Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138 configuration file to enable this feature. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* da850/omap-l138: Define SPI specific configs for SPL only when SPI is usedLad, Prabhakar2012-09-01-7/+10
| | | | | | | | | | define SPI specific configs for SPL only when CONFIG_USE_SPIFLASH config is defined Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* da850/omap-l138: Make MMC and NOR support mutually exclusiveRajashekhara, Sudhakar2012-09-01-0/+2
| | | | | | | | | | | | On Logic PD Rev.3 DA850/OMAP-L138 EVM, NOR and MMC/SD cannot work together. This patch enables the MMC/SD support only when NOR support is disabled. NOR Flash identification works even without this patch, but erase and write will have issues. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* da850/omap-l138: Add MMC support for DA850/OMAP-L138Lad, Prabhakar2012-09-01-0/+17
| | | | | | | | | This patch adds support for MMC/SD on DA850/OMAP-L138. Tested-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
* omap: am335x_evm: remove unused definitionsSteve Sakoman2012-09-01-1/+0
| | | | | | | | | | UART_RESET, UART_CLK_RUNNING_MASK, and UART_SMART_IDLE_EN are defined inn evm.c but not used. Also removes unnecessary include of serial.h PHYS_DRAM_1_SIZE is defined in am335x_evm.h but never used. Signed-off-by: Steve Sakoman <steve@sakoman.com>
* OMAP3: mcx: read hot-water-button after resetStefano Babic2012-09-01-0/+2
| | | | | | | Detect hot-water-button to start a differnt image. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
* OMAP3: mcx: updated default environmentStefano Babic2012-09-01-37/+91
| | | | | | | | Patch drops also not used CFI setup in the configuration file. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
* mcx: increased buffer for command lineStefano Babic2012-09-01-1/+1
| | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <trini@ti.com>
* hawkboard/omapl-138: Add support for generating ais image for hawkboardSughosh Ganu2012-09-01-0/+1
| | | | | | | | | Parameters used for configuring certain SoC peripherals are parsed from the cfg file and appended as part of the ais image's header. The u-boot-spl.ais generated is flashed separately to the nand, so do not delete the file after generation of u-boot.ais. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
* Consolidate bootcount code into drivers/bootcountStefan Roese2012-09-01-0/+6
| | | | | | | | | | | | | | | | | | | This patch moves all bootcount implementations into a common directory: drivers/bootcount. The generic bootcount driver is now usable not only by powerpc platforms, but others as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Manfred Rudigier <manfred.rudigier@omicron.at> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de> Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com> Tested-by: Christian Riesch <christian.riesch@omicron.at> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
* mpc52xx: remove o2dnt boardAnatolij Gustschin2012-09-01-297/+0
| | | | | | | Remove old o2dnt board without OF support. New support for this board is added by the previous patch, O2I configuration. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* mpc52xx: add common o2dnt and o2dnt2 support and configurationsAnatolij Gustschin2012-09-01-0/+834
| | | | | | | | Add common code for o2dnt and o2dnt2 based boards and add different board configuration files for O2D, O2I, O2DNT2, O2D300, O2MNT and O3DNT boards. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* rename EB+MCF-EV123 to its current marketing name EB+CPU5282Jens Scharsig2012-08-09-5/+5
| | | | | | | | | * rename board directory to eb_cpu5282 * rename EB+MCF-EV123_.*config to eb_cpu5282_.*config * add Maintainer for EB+CPU5282 board * rename prompt Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
* configs: Remove unused symbol CONFIG_DISCOVER_PHYFabio Estevam2012-08-09-10/+0
| | | | | | CONFIG_DISCOVER_PHY is not used anywhere, so remove it from config files. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* powerpc/85xx: improve definition of BR_PHYS_ADDR macroTimur Tabi2012-08-08-20/+18
| | | | | | | | The BR_PHYS_ADDR(x) macro was missing parentheses around "x" in the macro definition, so callers had to supply their own parenthesis. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is definedShaohui Xie2012-08-08-1/+6
| | | | | | | | | | ENV location compile logic is wrong, and when CONFIG_SYS_NO_FLASH is defined and non-NOR u-boot is building, it will cause compile error. Also, add CONFIG_SYS_FLASH_USE_BUFFER_WRITE for p2041, which will improve NOR flash write performance. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p1022ds: add support for SPI and SD bootMatthew McClintock2012-08-08-3/+48
| | | | | | | | | | | | | | | | | | Add TLB mappings, board target options, and configuration items need for SPI/SD boot. Since P1022DS RevB board, the NOR flash have been changed to 16 bit/28bit address flash, therefore, when SDHC/ESPI booting and access to eLBC, the PMUXCR[0~1] must be set to 10b, and PMUXCR[9~10] must be set to 00b for them. Configure the PX_BRDCFG0[0~1] to 10b which is connected to SPI devices as SPI_CS(0:3)_B. Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/82xx: adapt SDRAM settings for mgcoge3neGerlando Falauto2012-07-31-2/+4
| | | | | | | | | | The HW guys suggested to change these two values. And these values are now identical to the values we use on mgcoge. PSDMR_WRC was set to 1C as it should lead to better performance. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* powerpc/82xx: use SDRAM detection for mgcoge2neGerlando Falauto2012-07-31-4/+13
| | | | | | | | | | | | | | mgcoge2ne was an intermediate step towards mgcoge3ne. One difference is the smaller SDRAM on mgcoge2ne (128MB). To support both boards with the same u-boot we use here the SDRAM detection. This patch enables SDRAM detection between 256MB and 128MB. So in addition to the existing 256MB geometry: 4 chips x 8M (13 rows, 10 cols) x 16 bit x 4 banks we can now also have 128MB geometry: 4 chips x 4M (13 rows, 9 cols) x 16 bit x 4 banks Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
* powerpc/82xx: move km/km82xx-common.h within km82xx.hGerlando Falauto2012-07-31-318/+289
| | | | | | | The only file including km82xx-common.h is km82xx.h. So there is no need to have it as a separate file. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
* powerpc/82xx: merge mgcoge.h and mgcoge3ne.h into km82xx.hGerlando Falauto2012-07-31-94/+57
| | | | | | | | | Since mgcoge and mgcoge3ne are the only km82xx boards, there is no need to keep them as separate .h config files. Therefore, make mgcoge3ne.h and mgcoge.h converge into a single km82xx.h file. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
generated by cgit v1.1 at 2024-08-19 12:58:23 +0000