summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* arm: ls1021a: Add CONFIG_DOS_PARTITION and CONFIG_CMD_FAT supportAlison Wang2014-12-11-0/+6
| | | | | | | | This patch will fix the bug that the partitions on the SD card could not be accessed and add the support for the FAT fs. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add SD boot support for LS1021ATWR boardAlison Wang2014-12-11-0/+44
| | | | | | | | | | | | This patch adds SD boot support for LS1021ATWR board. SPL framework is used. PBL initialize the internal RAM and copy SPL to it, then SPL initialize DDR using SPD and copy u-boot from SD card to DDR, finally SPL transfer control to u-boot. Signed-off-by: Chen Lu <chen.lu@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add SD boot support for LS1021AQDS boardAlison Wang2014-12-11-0/+45
| | | | | | | | | | | This patch adds SD boot support for LS1021AQDS board. SPL framework is used. PBL initialize the internal RAM and copy SPL to it, then SPL initialize DDR using SPD and copy u-boot from SD card to DDR, finally SPL transfer control to u-boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Update PCIe dts node statusMinghuan Lian2014-12-11-0/+15
| | | | | | | | The patch changes PCIe dts node status to 'disabled' if the corresponding controller is disabled according to serdes protocol. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge git://git.denx.de/u-boot-mpc85xxTom Rini2014-12-08-14/+1886
|\
| * powerpc/t4240rdb: enable eSDHC 3.3V supportXiaobo Xie2014-12-05-0/+1
| | | | | | | | | | | | | | | | The SD supply Voltage was 3.3V on T4240RDB, so enabled 3.3V support for eSDHC. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Wujie Qiu <B49553@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/t1024qds: add retimer support on t1024qdsShengzhou Liu2014-12-05-1/+4
| | | | | | | | | | | | | | Initialize retimer for XFI on t1024qds. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t1024rdb: Add T1024 RDB board supportShengzhou Liu2014-12-05-0/+896
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC. T1024RDB board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - one 10Gbps XFI interface - PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors. - SerDes: 4 lanes up to 10.3125GHz - IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD - eSPI: 64MB N25Q512 SPI flash. - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - USB: Two Type-A USB2.0 ports with internal PHY - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC - I2C: Four I2C controllers - UART: Two UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t1024qds: Add T1024 QDS board supportShengzhou Liu2014-12-05-0/+936
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1024QDS is a high-performance computing evaluation, development and test platform for T1024 QorIQ Power Architecture processor. T1024QDS board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Three 1G/2.5Gbps SGMII ports - Four 1Gbps QSGMII ports - one 10Gbps XFI or 10Base-KR interface - SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora - PCIe: Three PCI Express controllers with five PCIe slots. - IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - Video: DIU supports video up to 1280x1024x32 bpp. - Chrontel CH7201 for HDMI connection. - TI DS90C387R for direct LCD connection. - Raw (not encoded) video connector for testing or other encoders. - QUICC Engine block - 32-bit RISC controller for flexible support of the communications peripherals - Serial DMA channel for receive and transmit on all serial channels - Two universal communication controllers, supporting TDM, HDLC, and UART - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - eSPI: Three SPI flash devices. - SATA: one SATA 2.O. - USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC. - I2C: Four I2C controllers. - UART: Two UART on board. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/b4860qds: add workaround for XFIShaohui Xie2014-12-05-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | XFI does not work stable on current board, it's due to heat sink issue, to make it work stable the board needs additional heat sink, enable two XFI lanes only. Right now we do not have such an erratum for the issue, so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it. The workaround will only be used in XFI protocols and only if the hwconfig indicates that XFI is prefered. A new VSC3308 config function is used instead of re-use the original function, to avoid making the function complex and ugly. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * B4860QDS: SGMII related updatesShaveta Leekha2014-12-05-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | - Enable SGMII support for 0x8d Serdes 2 protocol. - Correct Phy address for DTSECx for 0x8d/0xb2 Serdes 2 protocol. - Updated debug statement - Add Alternate LC VCO protocols(0x8d-->0x8c, 0xb2-->0xb1) - Rename onboard PHY address defines for more readability - Add these new Defines in B4860QDS.h file Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t104x: Convert to use generic board codevijay rai2014-12-05-0/+4
| | | | | | | | | | | | | | Convert T1040QDS and T1040RDB to use generic board code. Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/c29xpcie: Enable configs to use generic board codeChunhe Lan2014-12-05-0/+2
| | | | | | | | | | | | | | | | | | | | | | Add configs: o CONFIG_SYS_GENERIC_BOARD o CONFIG_DISPLAY_BOARDINFO in C29XPCIE config header file to use U-boot generic board code. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/p1023rdb: Enable configs to use generic board codeChunhe Lan2014-12-05-0/+3
| | | | | | | | | | | | | | | | | | | | | | Add configs: o CONFIG_SYS_GENERIC_BOARD o CONFIG_DISPLAY_BOARDINFO in P1023RDB config header file to use U-boot generic board code. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * mpc85xx/p1022ds: convert to generic boardTang Yuantian2014-12-05-0/+3
| | | | | | | | | | Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc, muas3001: remove CONFIG_SYS_RAMBOOTHeiko Schocher2014-12-05-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | cppcheck reports: [board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize remove the CONFIG_SYS_RAMBOOT define to prevent this error report. Signed-off-by: Heiko Schocher <hs@denx.de> Reported-by: Wolfgang Denk <wd@denx.de> Reviewed-by: York Sun <yorksun@freescale.com>
| * km/km82xx: remove CONFIG_SYS_RAMBOOTHolger Brunck2014-12-05-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | This define is never set in our setup, so we can remove it safely. The former code causes cppcheck to complain about: [board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable: psize Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Wolfgang Denk <wd@denx.de> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/freescale: use generic board architecture for p1010rdbYing Zhang2014-12-05-0/+2
| | | | | | | | | | | | | | | | Use generic board architecture for p1010rdb, tested with NOR boot on p1010rdb-pb. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/P5040DS: enable SATA supportShaohui Xie2014-12-05-0/+1
| | | | | | | | | | | | | | | | The define CONFIG_FSL_SATA_V2 is missing, so SATA is not available in U-boot. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * board/freescale: use generic board architecture for p1025-twrYing Zhang2014-12-05-0/+2
| | | | | | | | | | | | | | | | Use generic board architecture for p1025-twr, tested with NOR boot and NAND boot on p1025-twr. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t208xqds: VID supportYing Zhang2014-12-05-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/mpc85xx:Put errata number for T104x NAND boot issuePrabhakar Kushwaha2014-12-05-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | When device is configured to load RCW from NAND flash IFC_A[16:31] are driven low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using IFC_A[16:31] lines are not accessible. Workaround is already in-place. Put the errata number to adhere errata handling framework. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t1040qds: Update DDR optionYork Sun2014-12-05-3/+2
| | | | | | | | | | | | | | | | | | Enable interactive debugging by default. Remove DDR controller interleaving because this SoC only has one controller. Use auto chip-select interleaving to detect number of ranks. Signed-off-by: York Sun <yorksun@freescale.com> CC: Poonam Aggrwal <poonam.aggrwal@freescale.com>
| * mpc85xx/t208xqds: Adjust DDR timing parametersYork Sun2014-12-05-1/+1
| | | | | | | | | | | | | | | | | | | | | | Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of 1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in case such DIMM comes available. Also update single-rank 1866 timing. Enable interactive debugging as well. Signed-off-by: York Sun <yorksun@freescale.com> CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini2014-12-08-3/+101
|\ \
| * | arm, am335x: siemens boards add FIT supportHeiko Schocher2014-12-04-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | add FIT support and set "boardid" from factoryset records "DEV/id" and "COMP/ver". "boardid" is used for selecting which fit configuration gets booted on the board. Signed-off-by: Heiko Schocher <hs@denx.de>
| * | ARM: OMAP5: DRA7xx: Enable 8-bit eMMC access on the dra7xx_evmLubomir Popov2014-12-04-0/+1
| | | | | | | | | | | | | | | | | | | | | Tested on a Vayu EVM Rev.E2 with DRA752 ES1.1 Signed-off-by: Lubomir Popov <l-popov@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | beagle_x15: add board support for Beagle x15Felipe Balbi2014-12-04-0/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BeagleBoard-X15 is the next generation Open Source Hardware BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHZ A15 processor. The platform features 2GB DDR3L (w/dual 32bit busses), eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60), separate LCD port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G Ethernet. For more information, refer to: http://www.elinux.org/Beagleboard:BeagleBoard-X15 Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | configs: omap5_common : Boot rootfs from sd card by defaultFranklin S Cooper Jr2014-12-04-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Since the emmc isn't always programed trying to load the fs from the emmc causes boot failures/kernel panic. * The current bootcmd is set to: bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \ setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot; My guess is the env variables should be set so that sd card boot (dt,kernel,fs) is the default and then fallback to emmc if it fails (no sd card detected) The current bootcmd attempts to set mmcroot to the sd card rootfs but that code doesn't run due to mmcboot being ran early on. Signed-off-by: Franklin Cooper Jr. <fcooper@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
| * | arm: omap5: don't enable misc_init_r by defaultFelipe Balbi2014-12-04-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Out of all OMAP5-like boards, only one of them needs CONFIG_MISC_INIT_R, so it's best to enable that for that particular board only, instead of enabling for all boards unconditionally. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini2014-12-08-179/+47
|\ \ \
| * | | ARM: UniPhier: detect the number of flash banks at run-timeMasahiro Yamada2014-12-09-11/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some UniPhier boards are equipped with an expansion slot that some optional SRAM/NOR-flash cards can be attached to. So, run-time detection of the number of flash banks would be more user-friendly. Until this commit, UniPhier boards have achieved this by (ab)using board_flash_wp_on() because the boot failed if flash_size got zero. Fortunately, this problem was solved by commit 70879a92561a (flash: do not fail even if flash_size is zero). Now it is possible to throw away such a tricky workaround. This commit also enables CONFIG_SYS_MAX_FLASH_BANKS_DETECT for further refactoring. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | | ARM: UniPhier: merge UniPhier config headers into a single fileMasahiro Yamada2014-12-08-116/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some configurations have been moved to Kconfig and the difference among the config headers of UniPhier SoC variants is getting smaller and smaller. Now is a good time to merge them into a single file. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | | ARM: UniPhier: move support card select to KconfigMasahiro Yamada2014-12-08-51/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two kinds of expansion boards which are often used for the UniPhier platform and they are only exclusively selectable. It can be better described by the "choice" menu of Kconfig. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | | ARM: UniPhier: move CONFIG_UNIPHIER_SMP to KconfigMasahiro Yamada2014-12-08-2/+0
| | | | | | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | | ARM: UniPhier: disable autostart by defaultMasahiro Yamada2014-12-08-1/+0
| |/ / | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | | imx6: remove redudant CONFIG_SPL_START_S_PATH defineMasahiro Yamada2014-12-08-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | The CPU directory of IMX6 is arch/arm/cpu/armv7, so setting CONFIG_SPL_START_S_PATH to arch/arm/cpu/armv7 is totally redundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefano Babic <sbabic@denx.de>
* | | powerpc: a3m071: remove redundant CONFIG_SPL_* definesMasahiro Yamada2014-12-08-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The CPU directory of this board is arch/powerpc/cpu/mpc5xxx. Without the CONFIG_SPL_START_S_PATH and CONFIG_SPL_LDSCRIPT defines, the same start.o and u-boot-spl.lds are selected by default. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
* | | powerpc: lwmon5: remove redundant CONFIG_SPL_* definesMasahiro Yamada2014-12-08-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The CPU directory of this board is arch/powerpc/cpu/ppc4xx. Without the CONFIG_SPL_START_S_PATH and CONFIG_SPL_LDSCRIPT defines, the same start.o and u-boot-spl.lds are selected by default. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Stefan Roese <sr@denx.de>
* | | powerpc: mpc8xx: remove hermes board supportMasahiro Yamada2014-12-08-315/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This board sprinkles #ifdef(CONFIG_HERMES) over various global files such as include/common.h, common/board_r.c, common/cmd_bdinfo.c. Let's zap such an ill-behaved board. It has not been converted to generic board yet and mpc8xx is old enough. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
* | | ARM: rpi: support an environmentStephen Warren2014-12-08-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable ENV_IS_IN_FAT so that the environment can be stored persistently. It's stored in the FAT partition that the RPi firmware requires. On most RPis, this is on the SD card (which must be present in order for the system to boot). On the CM this is on the built-in eMMC device. Since we now have a persistent environment, there's no need to load uEnv.txt at boot; we only did that to work around the lack of persistent environment. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* | | ARM: rpi: rename rpi_b to rpiStephen Warren2014-12-08-0/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | The U-Boot port runs on a variety of RPi models, not just the B. So, rename the port to something slightly more generic. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* | | ARM: rpi_b: detect board revisionStephen Warren2014-12-08-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Detect the board revision early during boot, and print the decoded model name. Eventually, this information can be used for tasks such as: - Allowing/preventing USB device mode; some models have a USB device on- board so only host mode makes sense. Others connect the SoC directly to the USB connector, so device-mode might make sense. - The on-board USB hub/Ethernet requires different GPIOs to enable it, although luckily the default appears to be fine so far. - The compute module contains an on-board eMMC device, so we could store the environment there. Other models use an SD card and so don't support saving the environment (unless we store it in a file on the FAT boot partition...) Set $fdtfile based on this information. At present, the mainline Linux kernel doesn't contain a separate DTB for most models, but I hope that will change soon. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* | | MMC SD fs boot partition config coding style and proper descriptionPaul Kocialkowski2014-12-04-17/+17
|/ / | | | | | | | | | | | | | | | | | | | | CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION ought to be called CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to keep it consistent with other config options such as: CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR. In addition, it is not related to raw mode booting but to fs mode instead. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@ti.com>
* | Merge git://git.denx.de/u-boot-x86Tom Rini2014-12-01-15/+15
|\ \
| * | x86: chromebook_link: Enable the Chrome OS ECSimon Glass2014-11-25-0/+5
| | | | | | | | | | | | | | | | | | Enable the Chrome OS EC so that it can be used from U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | x86: chromebook_link: Enable the x86 emulatorSimon Glass2014-11-25-0/+4
| | | | | | | | | | | | | | | | | | Enable this so that it can be used instead of native execution if desired. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | x86: config: Enable video support for chromebook_linkSimon Glass2014-11-25-7/+3
| | | | | | | | | | | | | | | | | | | | | Now that we have the required drivers, enable video support with a suitable option ROM. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | x86: config: Enable SPI for chromebook_linkSimon Glass2014-11-25-4/+0
| | | | | | | | | | | | | | | | | | Enable SPI so that the SPI flash can be used. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | x86: config: Enable USB on linkSimon Glass2014-11-25-2/+0
| | | | | | | | | | | | | | | | | | Enable USB support on link - there are two EHCI ports available. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-11-19 18:32:05 +0000