summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* powerpc/85xx: Enable eSDHC boot support on P2020 DSJerry Huang2011-04-04-0/+25
| | | | | | | | | | | We implement our own mmc_get_env_addr since the environment variables are written to just after the u-boot image on SDCard, so we must read the MBR to get the start address and code length of the u-boot image, then calculate the address of the env. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add 36-bit address map support to P1022DSJiang Yutang2011-04-04-1/+45
| | | | | Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add support for ULI1575 PCI EHCI module on MPC8572DSZhao Chenhui2011-04-04-0/+14
| | | | | | | | MPC8572DS provides 2 USB ports with ULI1575. We enable USB storage device support using PCI EHCI module. Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Disable ECC in considering performance on MPC8572DSZhao Chenhui2011-04-04-1/+1
| | | | | Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Replace memctl_intlv_ctl with hwconfig on MPC8572DSZhao Chenhui2011-04-04-1/+1
| | | | | Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add 36-bit physical addressing support for P1_P2_RDBPoonam Aggrwal2011-04-04-3/+64
| | | | | | | | Add support for 36-bit address map for NOR, SD, and SPI boot cfgs. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Read board switch settings on p1_p2_rdbPriyanka Jain2011-04-04-0/+2
| | | | | | | | | | | | | | | | | | | | | PCA9557 is parallel I/O expansion device on I2C bus which stores various board switch settings like NOR Flash-Bank selection, SD Data width. On board: switch SW5[6] is to select width for eSDHC ON - 4-bit [Enable eSPI] OFF - 8-bit [Disable eSPI] switch SW4[8] is to select NOR Flash Bank for Booting OFF - Primary Bank ON - Secondary Bank Read board switch settings on p1_p2_rdb and configure corresponding eSDHC width. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Use DDR for RAMBOOT instead of L2 SRAM on p1_p2_rdbPriyanka Jain2011-04-04-4/+4
| | | | | | | | | | | | | | | | | | Using DDR as RAMBOOT base instead of L2SRAM for SDCard and SPI Flash boot loaders because: - P1_P2_RDB boards have soldered DDR so no need for SPD - Also P102x has 256K L2 cache size so becomes a limiting factor for size of image that could be loaded in SRAM mode and would require three stage boot loader (TPL). Changes done: 1. CONFIG_SYS_TEXT_BASE to 0x11000000 2. CONFIG_RESET_VECTOR_ADDRESS to 0x1107fffc Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Use BR_PHYS_ADDR macro to setup BRs on P1_P2_RDBPoonam Aggrwal2011-04-04-2/+3
| | | | | Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Refactor Qman/Portal support to be shared between SoCsHaiying Wang2011-04-04-0/+1
| | | | | | | | | | | | | | There are some differences between CoreNet (P2040, P3041, P5020, P4080) and and non-CoreNet (P1017, P1023) based SoCs in what features exist and the memory maps. * Rename various immap defines to remove _CORENET_ if they are shared * Added P1023/P1017 specific memory offsets * Only setup LIODNs or LIODN related code on CORENET based SoCs (features doesn't exist on P1023/P1017) Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Refactor fsl_ddr_get_spd into common code from boardKumar Gala2011-04-04-6/+5
| | | | | | | | | | | | | | Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards pretty much do the same thing. The only variations are in how many controllers or DIMMs per controller exist. To make this work we standardize on the names of the SPD_EEPROM_ADDRESS defines based on the use case of the board. We allow boards to override get_spd to either do board specific fixups to the SPD data or deal with any unique behavior of how the SPD eeproms are wired up. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Remove config.mk for nand linker scriptKumar Gala2011-04-04-0/+4
| | | | | | | Move the include of mpc85xx/u-boot-nand.lds to utilize CONFIG_SYS_LDSCRIPT rather than having an explicit config.mk Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Update P2020DS default env settingsLi Yang2011-04-04-10/+12
| | | | | | | | | | | | | | Read MAC address from EEPROM. Add hwconfig settings. Modified the default othbootargs to include the cache-sram-size parameter. This parameter is needed as the L2 as SRAM is ON by default in the P2020RDB kernel and used by the Gianfar driver. Also cleanup some of the boot commands. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add eSDHC support on P2020DSJerry Huang2011-04-04-1/+24
| | | | | | | | | | | We enable SDHC_CD and SDHC_WP signals (pin muxed with GPIO8 & GPIO9 respectively). We enable EXT2, FAT, and parition support for both MMC & USB configs. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Enable various errata on P1022/P1013 SoCsJiang Yutang2011-03-28-0/+1
| | | | | | | | | | Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on P1022/P1013 SoCs. Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2. Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-03-27-1/+15
|\
| * arm: Tegra2: Change mach-type to MACH_TYPE_SEABOARD due to mach-types.h updateTom Warren2011-03-27-1/+1
| | | | | | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
| * S5P: universal: Enable the pwm driverMinkyu Kang2011-03-27-0/+3
| | | | | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * S5P: goni: Enable the pwm driverMinkyu Kang2011-03-27-0/+3
| | | | | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * S5P: smdkc100: Enable the pwm driverMinkyu Kang2011-03-27-0/+3
| | | | | | | | Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * SMDK6400: Fix CONFIG_SYS_INIT_SP_ADDR undefinedseedshope2011-03-27-0/+5
| | | | | | | | | | | | | | Fix CONFIG_SYS_INIT_SP_ADDR undefined issue. Signed-off-by: Zhong Hongbo <bocui107@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | powerpc/85xx: Fix PCI memory map setup on P1_P2_RDBPrabhakar Kushwaha2011-03-24-12/+12
|/ | | | | | | | | Update the PCIe address map to match standard FSL memory map. Additionally, fix the TLBs so the cover the PCIe address space properly so cards plugged in like an e1000 work correctly. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc52xx, digsy_mtc_rev5: Fix Linux crash, if no Flash in bank 2Heiko Schocher2011-03-21-2/+2
| | | | | | | | | | | | | | | | If no Flash is connected to cs1, Linux crashes, because reg entries are not correct adapted. Following fix is needed: - swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as flash bank 1 is on chipselect 0 and flash bank 2 on chipselect 1 - call fdt_fixup_nor_flash_size() from ft_board_setup() Signed-off-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <hs@denx.de> cc: Werner Pfister <Pfister_Werner@intercontrol.de> cc: Detlev Zundel <dzu@denx.de>
* powerpc/85xx: Fix pixis_reset altbank mask on MPC8536DSMatthew McClintock2011-03-06-1/+1
| | | | | | | | Currently, pixis_reset altbank does not work properly. This patch uses the correct mask to boot into the alternate bank. Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Pantheon: Add Board Support for Marvell dkb boardLei Wen2011-02-21-0/+65
| | | | | | | | | | | | | | | | | | | | | | | | DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with * Processor upto 806Mhz * LPDDR1/2 * x8/x16 SLC/MLC NAND * Footprints for eMMC & MMC x8 card With Peripherals: * Parallel LCD I/F * Audio codecs (88PM8607) * MIPI CSI-2 camera * Marvell 88W8787 802.11n/BT module * Marvell 2G/3G RF * Dual analog mics & speakers, headset jack, LED, ambient * USB2.0 HS host, OTG (mini AB) * GPIO, GPIO expander with DIP switches for easier selection * UART serial over USB, CIR This patch adds basic board support with DRAM and UART functionality Signed-off-by: Lei Wen <leiwen@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* mv: seperate kirkwood and armada from common settingLei Wen2011-02-21-126/+29
| | | | | | | | | | | | | Since there are lots of difference between kirkwood and armada series, it is better to seperate them but still keep the most common file shared by all marvell platform in the mv-common configure file. This patch move the kirkwood only driver definitoin in mv-common to the <soc_name>/config.h. This patch is tested with compilation for armada100 and guruplug. Signed-off-by: Lei Wen <leiwen@marvell.com>
* arm: Tegra2: Add support for NVIDIA Seaboard boardTom Warren2011-02-21-0/+43
| | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
* arm: Tegra2: Add support for NVIDIA Harmony boardTom Warren2011-02-21-0/+209
| | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
* mx31pdk: Make the full boot log visibleFabio Estevam2011-02-21-0/+1
| | | | | | Use board_early_init_f so that the full boot log output can be displayed. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx31pdk: Use the new relocation schemeFabio Estevam2011-02-21-0/+6
| | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mipsWolfgang Denk2011-02-12-5/+11
|\
| * MIPS: Move Inca-IP targets to boards.cfgShinya Kuribayashi2011-02-05-3/+6
| | | | | | | | | | | | At the same time, fix up CPU_CLOCK_RATE to have the CONFIG_ prefix to work with boards.cfg. Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
| * MIPS: VCT: Fix enabling of unwanted options if networking or USB support are ↵Daniel Schwierzeck2011-02-05-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | disabled Some VCT boards lacks the support of networking or USB. Additionally that support is disabled in small image configurations. If CONFIG_CMD_NET should not used the CONFIG_CMD_NFS option have to be disabled too. Otherwise the linker fails with unresolved symbols. If CONFIG_VCT_SMALL_IMAGE is set than CONFIG_CMD_NET and CONFIG_CMD_USB are disabled at the end of vct.h. This is not adequate because CONFIG_CMD_USB enables additional options and the linker fails again with unresolved symbols. This patch adds an early check against CONFIG_VCT_SMALL_IMAGE so the additional options are only enabled if they are really needed. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
* | eNET: Move initial Global Data into CARGraeme Russ2011-02-12-1/+1
| |
* | sc520: Move RAM sizing code from asm to CGraeme Russ2011-02-12-1/+1
| |
* | x86: Use Cache-As-RAM for initial stackGraeme Russ2011-02-12-0/+20
| |
* | x86: Move initial gd to fixed locationGraeme Russ2011-02-12-0/+3
| |
* | eNET: General code cleanupGraeme Russ2011-02-12-166/+125
| |
* | eNET: Rearrange PAR assignmentsGraeme Russ2011-02-12-15/+0
| |
* | eNET: Define MMCR values in config.hGraeme Russ2011-02-12-0/+382
| |
* | eNET: Add RTC support to eNETGraeme Russ2011-02-12-0/+2
| | | | | | | | The SC520 has an inbuilt MC146818 - Enable it for the eNET board
* | powerpc/85xx: corrected p1_p2_rdb EEPROM addressPriyanka Jain2011-02-09-2/+1
| | | | | | | | | | | | | | Board EEPROM is used to read/save Ethernet MAC addresses. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2011-02-09-8/+341
|\ \
| * | ppc4xx: Add DLVision-10G board supportDirk Eibach2011-02-07-8/+341
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Board support for the Guntermann & Drunck DLVision-10G. Adds support for multiple FPGAs per board for gdsys 405ep architecture. Adds support for dual link osd hardware for gdsys 405ep. Signed-off-by: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2011-02-06-1/+2
|\ \ \ | |_|/ |/| |
| * | powerpc/85xx: Enable ECC on MPC8572DSYork Sun2011-02-03-0/+1
| | | | | | | | | | | | | | | | | | | | | Using hwconfig to turn on/off ECC, without re-compiling. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * | powerpc/85xx: Enable Errata command on MPC8572DSYork Sun2011-02-03-1/+1
| |/ | | | | | | | | | | | | Also removed duplicate CONFIG_CMD_IRQ define. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk2011-02-04-0/+162
|\ \ | |/ |/|
| * sh: add support for sh7757lcr boardYoshihiro Shimoda2011-02-02-0/+146
| | | | | | | | | | | | | | | | | | | | | | | | | | The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM, Ethernet, and more. This patch supports the following functions: - 256MB DDR3-SDRAM - SPI ROM - Ethernet Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * sh: Remove config.mk for shmin boardNobuhiro Iwamatsu2011-02-02-0/+1
| | | | | | | | | | | | | | Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the unnecessary config.mk file. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
generated by cgit v1.1 at 2024-11-18 08:39:03 +0000