summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* ENGR00214947 MX6 UBOOT : default enable wait mode as default parametersEric Sun2012-06-26-8/+6
| | | | | | | | For historical reasons U-Boot set "enable_wait_mode=off" in default U-Boot parameter. Now wait mode is OK for these platforms so we remove these settings. Signed-off-by: Eric Sun <jian.sun@freescale.com>
* ENGR00213689 - U-Boot: EPDC Splash Screen failing for MX 6DL/SDanny Nold2012-06-14-4/+4
| | | | | | | | | | | Fix a hang and a garbage update to the E Ink panel with the following changes for both MX 6DL/S SabreSD and MX 6DL/S ARM2: - Update the address for the EPDC waveform file to 6MB offset in SD card. - Update the waveform file size to cover the default Pearl panel waveform file. Signed-off-by: Danny Nold <dannynold@freescale.com>
* ENGR00212229 [MX6SL_ARM2]uboot: 8bit MMC cards failed to boot on SD1.Ryan QIAN2012-06-08-4/+4
| | | | | | | | | | | | issue: SD1 connector on ARM2 is an MS-SD combo one which can not make good contact with DAT4~DAT7 of 8bit mmc cards. It is an hw limitation which will cause boot failure from 8bit mmc. solution: disable SD1 8bit mode on MX6SL arm2 board. Signed-off-by: Ryan QIAN <b32804@freescale.com>
* ENGR00212287 - U-Boot EPDC splash screen: Disable EPDC splash by defaultDanny Nold2012-06-04-4/+4
| | | | | | | | | | - EPDC splash screen changed to be disabled by default in the config file for MX6DL_SABRESD and MX6DL_ARM2. If left enabled, the U-Boot image will not boot correctly (hang), since some additional content on the boot device (waveform file) is required for EPDC splash to work correctly. - Fixes U-Boot break introduced with commit for ENGR00212287 Signed-off-by: Danny Nold <dannynold@freescale.com>
* ENGR00211117 - U-Boot: Add EPDC splash screen for MX 6DL/S platformsDanny Nold2012-05-30-4/+56
| | | | | | | | | - EPDC Splash support for MX6DL/S Sabre SD - EPDC Splash support for MX6DL/S ARM2 - Currently, splash screen consists of a simple black border around a white screen. Done this way to save in memory footprint. Signed-off-by: Danny Nold <dannynold@freescale.com>
* ENGR00210918-2 cleanup android support, build pass all boardsZhang Jiejing2012-05-29-2/+12
| | | | | | | | | | - move recovery.h to common inlcude place. - move supported_reco_envs to soc related, not board related, - user can change this via configure header, don't needs this in every board file. - pass build for all mx5/mx6 android configs. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00210918-1 android: add mx6sl android supportZhang Jiejing2012-05-29-0/+75
| | | | | | | | | | - add android build config for mx6sl_arm2 board. - add gpio support for mx6sl - add boot image support - add android recovery support - add fastboot support, but fastboot cannot transfer file. Signed-off-by Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00209910 Add support for MX6SL mfgtools firmware supportFrank Li2012-05-21-0/+287
| | | | | | Add support for MX6SL mfgtools firmware support Signed-off-by: Frank Li <Frank.Li@freescale.com>
* ENGR00209899-1 mx6x: add generic gpio interface.Zhang Jiejing2012-05-21-1/+7
| | | | | | | | | | | | | | | | | | | | | | Add generic gpio interface in uboot. Seems more and more gpio operation invoke in uboot, without RAW register operation, we should use generic gpio interface. you should define the CONFIG_MXC_GPIO use generic gpio interface: gpio_request, gpio_direction_output, gpio_direction_input, gpio_set_value, gpio_get_value, etc. Test on MX6Q, MX6DL. Other MX6X should also define this config. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00182459 fastboot: change vid pid to align with winXP fastboot driver.Zhang Jiejing2012-05-11-20/+20
| | | | | | align vid, pid to let windows fastboot driver can be install. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00182017 mx6dl sabresd I2C: fix build error and support mx6dl_sabresdRobin Gong2012-05-07-2/+3
| | | | | | | | | | | | | | 1.fix build error : mx6q_sabresd.c: In function 'setup_i2c': mx6q_sabresd.c:382: error: expected ')' before ';' token mx6q_sabresd.c:393: error: expected ';' before '}' token mx6q_sabresd.c: In function 'setup_pmic_voltages': mx6q_sabresd.c:399: warning: unused variable 'val' make[1]: *** [mx6q_sabresd.o] Error 1 2.modify mx6dl_sabresd_config to support pfuze on mx6dl sabresd board Signed-off-by: Robin Gong <B38343@freescale.com>
* ENGR00181348 pfuze sabresd: pfuze support in u-bootRobin Gong2012-05-04-2/+3
| | | | | | add pfuze and I2C support, support cpu internal LDO bypass which can be enabled by CONFIG_MX6_INTER_LDO_BYPASS Signed-off-by: Robin Gong <B38343@freescale.com>
* ENGR00181621 : MX6Solo SABREAI - Set default boot up to SD CardPrabhu Sundararaj2012-05-03-1/+1
| | | | | | Set default boot to SD Card Signed-off-by: Prabhu Sundararaj <b36876@freescale.com>
* ENGR00181337-3 i.mx6: i.mx6sl: add initial support for i.mx6sl ARM2 boardEric Sun2012-05-03-0/+452
| | | | | | | | | | | | | | | | | This patch is to add the initial support for i.mx6sl ARM2 board, the patch does: - implemention of LPDDR2 init script - Plug-in/DCD mode support to do DDR initialization - Debug UART(UART1) support - SPI-NOR(M25P32, 4MB) flash support - FEC support, PHY(LAN8720A, RMII mode) - SD/MMC card support, SD1/SD2/SD3 Signed-off-by: Danny Nold <dannynold@freescale.com> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Terry Lv <r65388@freescale.com> Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com> Signed-off-by: Eric Sun <jian.sun@freescale.com>
* ENGR00180623 fastboot: add fastboot in MX6Q_SABERSD boardsZhang Jiejing2012-04-24-5/+20
| | | | | | | | add fastboot function back in MX6Q_SABERSD board. the MX6DL_SABERSD have usb init related issue which will keep RESET, but left as later developement. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00179013 : MX6Solo/Quad : SABREAUTO: Add Parallel NOR SupportPrabhu Sundararaj2012-04-13-7/+52
| | | | | | | | | | | | | -Added u-boot config CONFIG_CMD_WEIMNOR for MX6Solo/Quad SABREAUTO to support WEIM NOR. - CONFIG_FLASH_HEADER_OFFSET is 0x1000 for WEIM NOR. -SPI NOR and WEIM NOR has pin conflicts, either one can be enabled. - mx6q_sabreauto_config, mx6solo_sabreauto_config configured default for SPI NOR. -In order to enable the read/write commands and to boot from WEIM NOR, need to enable the CONFIG_CMD_WEIMNOR. This will disable SPI-NOR Signed-off-by: Prabhu Sundararaj <b36876@freescale.com>
* ENGR00179150 MX6Q_ARM2 HAB Boot : avoid uImage authentication on un-fused chipEric Sun2012-04-09-2/+0
| | | | | | | | | Before running authentication on uImage in DDR, u-boot first check if SEC_CONFIG[1] (OTP_CFG5[1]) is burned. If so, it means the chip is in secure configuration, the authentication continues; if not, the chip in not in secure configuration, just bypass the authentication Signed-off-by: Eric Sun <jian.sun@freescale.com>
* ENGR00178989: Disable secrity boot configs.Terry Lv2012-04-05-1/+3
| | | | | | | Security boot need to use fuse item. Thus it should not be enabled as default. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00139223-1 [MX6Q] Secure Boot, enable HAB on ARM2 platform (Stage 1)Eric Sun2012-04-01-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The first stage of High Assurance Boot (HAB) is the authentication of U-boot. A CST tool is used to generate the CSF data, which include public key, certificate and instruction of authentication process. Then it is attached to the original u-boot.bin The IVT should be modified to contain a pointer to the CSF data. The original u-boot.bin is with size between 0x27000 to 0x28000. For convinence, we first extend the u-boot.bin to 0x2F000 (with fill 0xFF). Then concatenate it with the CSF data. The combined image is again extend to a fixed length (0x31000), which is used as the IVT size parameter. The new memory layout is as the following. U-Boot Image +-------------+ | Blank | |-------------| 0x400 | IVT |-----------------------+ |-------------| | | | | | | | | | | |Remaining UB | | CSF pointer | | | | | | | | | |-------------| | | | | | Fill Data | | | | | |-------------| 0x2F000 <-------------+ | | | CSF Data | | | |-------------| | | | Fill Data | | | +-------------+ 0x31000 HAB APIs are ROM implemented, the entry table is located in a fixed location in the ROM. We export them so that during the HAB we can have some information about the secure boot process. For convinience some wrapper API is implemented based on the HAB APIs. - get_hab_status : used to dump information of authentication result - authenticate_image : used by u-boot to authenticate uImage For security hardware to function, CAAM related clock (CG0[4~6]) must be open. They are default closed in the original U-boot. "hab_caam_clock_enable" and "hab_caam_clock_disable" are created to open and close these clock gates. The generation of CSF data is not in the scope of this patch. CST tool will be used for this purpose. The procedure will be introduced in another document. Signed-off-by: Eric Sun <jian.sun@freescale.com>
* ENGR00178024 mx6solo sabreauto: add nosmp arm_freq=800 by defaultLily Zhang2012-03-30-2/+3
| | | | | | | Add "nosmp arm_freq=800" options for mx6solo sabreauto board by default Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00178547 i.mx6dl sabresd: add android config fileLin Fuzhen2012-03-30-0/+57
| | | | | | | add android config file; support booti fastboot command and etc. Signed-off-by: Lin Fuzhen <fuzhen.lin@freescale.com>
* ENGR00177909: mx6q/mx6dl SabreSD: SPI-NOR flash not probed as expectedJason Liu2012-03-26-3/+3
| | | | | | | | | | | | SPI NOR flash(m25p32-vmw6tg) not probed and function as expected, this due to the lack of iomux pad config and incorrect CS line. This patch fix the above issue and also fix the mfg config file (For the code readable, I intent to omit the following checkpatch warning: in the iomux/mx6_pins.h WARNING: line over 80 characters) Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00177905 : i.mx6q sabresd: add fec auto discover phy configuration.Fugang Duan2012-03-26-1/+2
| | | | | | | | - i.mx6q sabresd revA ethernet phy addr is 0 (PHYADDRESS1-PHYADDRESS0:00) , but revB ethernet phy address is 0x1 (PHYADDRESS1-PHYADDRESS0:01). To avoid to change hardware, add auto discover phy address configuration. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00177657: Add mfg configs for mx6dl sabresd and mx6solo sabreautoTerry Lv2012-03-23-0/+587
| | | | | | Add mfg configs for mx6dl sabresd and mx6solo sabreauto. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00176837-4 - imx6solo sabreauto : remove Ethernet phy MICREL macro.Fugang Duan2012-03-22-1/+0
| | | | | | | - FEC detect phy OUID to check phy type, so remove MICREL macro in board config file. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00177587 MX6Q_ARM2: add android config for this board.Zhang Jiejing2012-03-22-0/+83
| | | | | | | add android config to this board. only basic boot support. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00176834-2 - i.MX6DL sabresd: board bringupFugang Duan2012-03-20-0/+323
| | | | | | | | | | | | | The serial of patches adds the initial support for mx6dl sabra sd board: - DDR3 400MHz@64bit, 1G, 256M*4 - SD/MMC basic operations - Add PIN/IOMUX support for mmx6dl sabresd. - Ethernet is ok for 100/1000Mbps. - OTP fuse Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00177070 android: isolate booti command to fix build.Zhang Jiejing2012-03-16-0/+3
| | | | | | | | | | fix build error invoke by this patch: commit e3303f5b59df570c1f76b043d85e42be3dc7a63f Author: Lily Zhang <r58066@freescale.com> Date: Fri Mar 9 21:16:51 2012 +0800 Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00176347-1 mx6solo sabreauto: add configuration supportLily Zhang2012-03-13-0/+328
| | | | | | | | | | | | | | | | | | | | The serial of patches adds the initial support for mx6solo sabra auto board: - DDR3 400MHz@32bit - SD/MMC basic operations - SPI-NOR basic operations - OTP fuse - clock command - Anatop regulator command - splash screen support by enabling "CONFIG_SPLASH_SCREEN" Because i.mx6solo share the same ARD board with i.mx6dq, the same board file is shared between i.mx6dq and i.mx6solo. CONFIG_MX6DL configuration is used to distinguish the difference. This patch is used to add mx6solo sabreauto configuration support. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00176328 change fastboot vid to google orignalZhang Jiejing2012-03-07-5/+5
| | | | | | | Change fastboot vender id to orignal ID to avoid install USB driver. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00176235 mx6 ARD: Add splash screen supportLily Zhang2012-03-06-1/+1
| | | | | | | | | | | | | | | | | | | This patch adds splash screen support for MX6 ARD. Changes: - Configure GPIO_3 as I2C3_SCL - Change MAX7310 I2C address as 0x30 - Enable LVDS power Usage: 1. To enable splash screen by default, define CONFIG_SPLASH_SCREEN in mx6q_sabreauto.h 2. Config U-boot with followed command:() setenv splashimage '0x30000000' #Set splash position as Center setenv splashpos 'm,m' #Set LVDS via LVDS bridge 0 setenv lvds_num 0 Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00176186 mx6dq ARD: add MFG tool supportLily Zhang2012-03-06-0/+299
| | | | | | Add MFG tool support for i.MX6DQ ARD board Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00175981-2 mx53 smd android: fix build errorLily Zhang2012-03-02-1/+1
| | | | | | | | | Fix the following build error when building mx53_smd_android config: mx53_smd_android.h:175: error: expected identifier or xx before string constant Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00175981-1 mx53 smd: add CPU 1.2GHz configurationLily Zhang2012-03-02-2/+8
| | | | | | | | | CONFIG_CPU_1_2G is used to enable 1.2GHz@1.3V. To enable 1.2GHz by default, enable CONFIG_CPU_1_2G into config file. For example, uncomment CONFIG_CPU_1_2G in mx53_smd.h or mx53_smd_android.h. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00175117 [MX6DL LPDDR2 Board] Apply Initializtion script and enable U-BootEric Sun2012-02-29-0/+320
| | | | | | | | | | | | | | | | | Apply script "Mx6DL_init_LPDDR2_400MHz_Micron_1.1.inc" in IVT, make U-boot work for the LPDDR2 Board. The Make target name for the new board is "MX6DL_ARM2_LPDDR2_CONFIG" The script is provided by Chen Wei - B26879 for a quick bring up, which don't have a corresponding compass link. It is uploaded to CR ticket page for reference. Originally for MX6DL DDR3 board, "CONFIG_MX6DL" is defined. It is used by "board/freescale/mx6q_arm2/flash_header.S" to select the correct IVT. Since MX6DL LPDDR2 board also define this macro, for distiguish purpose, another 2 macros "CONFIG_MX6DL_DDR3", "CONFIG_MX6DL_LDPPR2" are defined Signed-off-by: Eric Sun <jian.sun@freescale.com>
* ENGR00175091 MX6Q_SABRESD: android: add recovery checkZhang Jiejing2012-02-27-0/+4
| | | | | | | | define a new macro to show which mmc bus was main storage in recovery check, only check the main storage /cache partition. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00174868 mx6dl arm2: change the default console as ttymxc3Lily Zhang2012-02-27-1/+1
| | | | | | | The default console on i.MX6DL ARM2 CPU board is ttymxc3 Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00174841 [U-Boot]Add a command to erase any pre-saved environmentEric Sun2012-02-27-28/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A "destroyenv" command is provided to erase any pre-save environment in the boot storage. The command simply add 1 to the CRC section and write it back to the storage. Per the logic of U-Boot, this means after a reset, the software will recognize the stored environment settings as "damaged" and turn to use the default one, which is defined in "default_environment" With this command, platform bring up owner can maintain a "ready-to-use" environment settings in software which others can use very conviniently. U-boot users can also use it to do a environment restore if they want. ----------------------------------- Usage Example: > destroyenv invalidate the CRC write invalidate enviroment data to storage Erasing SPI flash...Erasing SPI NOR flash 0xc0000 [0x2000 bytes] ..SUCCESS Writing to SPI flash...Writing SPI NOR flash 0xc0000 [0x2000 bytes] <- ram 0x276009b8 SUCCESS done > ----------------------------------- Signed-off-by: Eric Sun <jian.sun@freescale.com>
* ENGR00174536-2 MX6Q_SABRE[SD/Lite]: change bootcmd to bootiZhang Jiejing2012-02-27-32/+13
| | | | | | change boot command and recovery command to booti. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00174536-1 booti: add booti command support.Zhang Jiejing2012-02-27-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support booti command which can boot from a boot.img boot.img is a zImage + ramdisk.img + bootargs + boot addr which include these info can be used to avoid mis match between kernel and ramdisk, also can avoid commit to chagne default bootargs. For example: > booti mmc1 command will read the boot.img from 1M offset, and then parser the bootargs and ramdisk then do the boot from that zImage. > booti mmc1 recovery will going to read the recovery's partition no and offset and boot from recovery image. this recovery image also a zImage + ramdisk bootargs: if uboot have define a env var 'bootargs', booti command will use this bootargs as kernel cmdline if you want use boot.img 's bootargs, just type: > setenv bootargs in uboot to clear the bootargs in uboot env. our default uboot env will be NULL in config file. also, android use boot.img to support OTA. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00139213: Add read and change voltage support for mx6Terry Lv2012-02-16-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | dd read and change voltage support for mx6. For help, pls type "help regul" Detail command info: regul list - List all regulators' name regul show all - Display all regulators' voltage regul show core - Show core voltage in mV regul show periph - Show peripheral voltage in mV regul show <regulator name> - Show regulator's voltage in mV regul set core <voltage value> - Set core voltage in mV regul set periph <voltage value> - Set periph voltage in mV regul set <regulator name> <voltage value> - Set regulator's voltage in mV Example: MX6Q ARM2 U-Boot > regul list Name Voltage vddpu vddcore vddsoc vdd2p5 vdd1p1 vdd3p0 MX6Q ARM2 U-Boot > regul show all Name Voltage vddpu 1100000 vddcore 1100000 vddsoc 1200000 vdd2p5 2400000 vdd1p1 1100000 vdd3p0 3000000 MX6Q ARM2 U-Boot > regul show periph Name Voltage periph: 1100000 MX6Q ARM2 U-Boot > regul show core Name Voltage core: 1100000 MX6Q ARM2 U-Boot > regul set core 1100000 Set voltage succeed! Name Voltage core: 1100000 Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00174326 MX6Q_SABRESD: add android related function and config.Zhang Jiejing2012-02-15-1/+387
| | | | | | | | | | enable mfg profile. enable recovery mode. mx6q_sabresd board's usb otg have HW issue, disable it in android profile. Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
* ENGR00174407 imx6dl: add MFG tool supportLily Zhang2012-02-14-0/+305
| | | | | | Add MFG tool support in imx6dl U-boot Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00174230: Move partition command from nand to sata in mx6Terry Lv2012-02-13-16/+24
| | | | | | | Move partition command from nand to sata in mx6 for nand don't need these partition command. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00174104-3: Fix mx6 iram boot configs' issueTerry Lv2012-02-13-28/+2
| | | | | | | | Two issues are fixed: 1. Enlarge malloc size to 10K. 2. Too many configs in sabresd's iram config, remove redundent configs. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00174104-2: Add mx6dl iram boot configTerry Lv2012-02-13-0/+168
| | | | | | Add mx6dl iram boot config. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00174221 imx6dl remove unnecessary configs for NANDAllen Xu2012-02-10-4/+0
| | | | | | | CONFIG_DOS_PARTITION, CONFIG_CMD_FAT, CONFIG_CMD_EXT2 are only for MMC and SATA, remove from NAND config segment Signed-off-by: Allen Xu <allen.xu@freescale.com>
* ENGR00174155-3 i.mx6sdl: enable i.mx6solo config by defaultJason Liu2012-02-10-1/+1
| | | | | | remove arm_freq=800 from default env thus keep 1GHz for kernel Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00174155-2 i.mx6sdl: enable i.mx6solo config by defaultrel_imx_3.0.15_12.02.01imx_v2009.08_12.02.01Jason Liu2012-02-09-1/+2
| | | | | | enable i.mx6solo config by default Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00174155: i.mx6sdl: add 32bit DDR support on ARM2 boardJason Liu2012-02-09-0/+5
| | | | | | | | | | | The 32bit DDR script got from the following link: http://compass.freescale.net/livelink/livelink/225194568/ MX6DL_init_DDR3_400MHZ_32bit_1.0.inc.txt?func=doc.Fetch&nodeid=225194568 The DDR hw connection on the ARM2 board is 64bit wire, but we can make it use as 32bit, the side effect is that DDR access size will reduce to the half Signed-off-by: Jason Liu <r64343@freescale.com>
generated by cgit v1.1 at 2024-11-29 05:39:01 +0000