| Commit message (Collapse) | Author | Age | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add NAND support for MX53 EVK and ARD.
Need to use kobs-ng to flash U-Boot on MX53 TO1. Because
MX51 TO1 ROM doesn't support bi swap solution and kernel
enable bi swap, Must enable "ignore bad block" option when
flashing U-Boot. The step is as following:
echo 1 > /sys/devices/platform/mxc_nandv2_flash.0/ignorebad
kobs-ng init --chip_0_device_path=/dev/mtd2 u-boot.bin
echo 0 > /sys/devices/platform/mxc_nandv2_flash.0/ignorebad
Since default configuration stores environment into SD
card and U-Boot uses get_mmc_env_devno (Read SBMR register)
to get MMC/SD slot information, you must insert SD card to
bottom SD slot to get/store environment if you are using NAND
boot on MX53 EVK.
You must config boot dip setting well when doing NAND boot.
For example, if you are using NAND 29F32G080AA NAND chip on
MX53 EVK, you can set boot dips as the following for NAND
boot: SW3: dip 7, 8 on; SW2: dip 3,5 on; SW1: dip 4,7,8 on.
Other dips are off.
Signed-off-by: Lily Zhang <r58066@freescale.com>
|
|
|
|
|
|
|
| |
Add default uboot defconfig for MX53 ARD MFG
tool
Signed-off-by: Lily Zhang <r58066@freescale.com>
|
|
|
|
|
|
|
| |
Use serial_mxc as uart driver for MX53 MFG.
This change is required by ENGR00131779.
Signed-off-by: Lily Zhang <r58066@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This change make a bootable default setting of MX53 EVK and MX51 BBG board,
the old default setting is too old to boot android system up.
Also add the recovery command in the env strings, if you want
to boot to recovery mode with mx53_evk, you can just :
> run bootcmd_android_recovery
This command will boot android into recovery mode.
Also fix MX51 can't see UI in recovery mode.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
|
|
|
|
|
|
| |
using ext4 as default recovery filesystem.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
| |
Use serial_mxc as uart driver for MX53 ARD.
This change is required by ENGR00131779.
Signed-off-by: Lily Zhang <r58066@freescale.com>
|
|
|
|
|
|
|
|
|
|
| |
Add support for building uboot for MX50 reference design platform:
1) LPDDR2 init script (v0.3 from Mike Kjar, dated 9/14)
2) iomux
3) new board file and machine id for RDP
4) Updates for iram boot on RDP
Signed-off-by: Anish Trivedi <anish@freescale.com>
|
|
|
|
|
|
| |
Use serial_mxc as uart driver for all platforms.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Fix mx50 lpddr2 build errors.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Add MX53 Automotive Reference Board (ARD) support
1. Add DDR2 initialization script
2. Add external ethernet support
3. Update PIN settings for UART, I2C, SDHC etc
Signed-off-by: Anish Trivedi <anish@freescale.com>
Signed-off-by: Terry Lv <r65388@freescale.com>
Signed-off-by: Lily Zhang <r58066@freescale.com>
|
|
|
|
|
|
|
|
| |
iram boot don't work.
The reason is that ivt plugins copy too much data
than that iram can hold.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Add android recovery mode support for mx53.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Add gpmi nfc and apbh dma support for mx50.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
add DDR2 support for U-BOOT.
The infomation about the init script:
Date : Aug-30,2010
Author : Tommy
Version: 0.1
please check :
http://compass.freescale.net/doc/219931536/Codex_DDR2_266MHz.inc.txt
Signed-off-by: Huang Shijie <b32955@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Move the android recovery codes into common/recovery.c.
Cut the keypad detecting time. Now we only need detect
there's POWER and HOME key pressing at the time scanning
keyboard matrix. So user must hold these two keys when bootup to
enter recovery mode. This can reduce the uboot boot time with
recovery mode configured.
Later /cache file checking for recovery command should be merged
into the common/recovery.c
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
|
|
|
|
|
|
| |
Set the memroy size to 512M on LPDDR2 board
Signed-off-by: Jason Liu <r64343@freescale.com>
|
|
|
|
|
|
| |
Add clk command support for mx51.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Add splash screen code and support for epdc.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
The boot mode offset has been changed in TO1.2.
Signed-off-by: Aisheng.Dong <b29396@freescale.com>
|
|
|
|
|
|
| |
Read mac address from fuse
Signed-off-by: Frank Li <frank.li@freescale.com>
|
|
|
|
|
|
| |
Add mx50 mfg firmware support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
|
|
|
|
|
| |
Enable DDR mode on ESDHC controller and mmc library
Enable 8-bit support in mmc library
Signed-off-by: Anish Trivedi <anish@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently we set mx508 memory as 128M which is not
enough for android running.
Based on hardware team's input, mDDR boards support
512MB totally, while we only mount half of them.
LPDDR2 boards support 512MB.
So we will modify mddr configuration as 256M and
LPDDR2 as 512M.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
|
|
| |
1. Reconstructure fuse. Move fuse files to common directory.
2. Read mac from fuse in fec.
3. Remove scc and srk command from fuse command.
4. Change fuse to iim.
5. Add fuse for mx53.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
| |
Fix error in a comment for header file
Fix ppp review about error board description
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
|
|
|
|
|
|
| |
MMC init failed when boot with upper SD slot
while succesful with lower slot.
This patch will fix it.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add initial support for MX50
-Support mddr200Mhz, lpddr2266Mhz ARM2 board,
-Support boot from SD/MMC,
-Support boot from SPI-NOR,
-Support FEC, UART,
-Support SD/MMC/SPI command within UBOOT
Signed-off-by: Anish Trivedi <anish@freescale.com>
Signed-off-by: Terry Lv <r65388@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
|
|
|
|
|
|
| |
Add MFG tool support for MX53 EVK
Signed-off-by: Lily Zhang <r58066@freescale.com>
|
|
|
|
|
|
| |
Added dynamic check for which sd slot used for boot
Signed-off-by: Anish Trivedi <anish@freescale.com>
|
|
|
|
|
|
| |
Enable boot partition in BOOT_CONFIG byte of EXT_CSD
Signed-off-by: Anish Trivedi <anish@freescale.com>
|
|
|
|
|
|
| |
Add dwc_ahsata support.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
| |
The old config has big env size, and the u-boot.bin will larger than 1MB,
the new one will less than 500KB
Signed-off-by: Peter Chen <b29397@freescale.com>
|
|
|
|
|
|
|
|
|
| |
Original uboot did not support sd1 and can only save environment
into sd0 even actually you're booting from sd1.
This patch adds the capability of saving environment into sd1
when you're booting from sd1.
Signed-off-by: Aisheng.Dong <b29396@freescale.com>
|
|
|
|
|
|
|
|
| |
Add mx25 splash screen support.
Signed-off-by: Terry Lv <r65388@freescale.com>
Signed-off-by: Renato Frias <renato.frias@freescale.com>
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
| |
Add DDR3 CPU board support, DDR3 clock 400Mhz
Create one config file for it since the DDR3 init
script is much different wtih DDR2.
Signed-off-by:Jason Liu <r64343@freescale.com>
|
|
|
|
|
|
| |
Support clock operation functions.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
| |
As customer usually mmc to save env data.
Change default env device to mmc for bbg.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Integrate linear PMIC.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Change stmp378x to mx23evk in u-boot.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Add mfg firmware support for imx25
Signed-off-by:Yan Wang<r65094@freescale.com>
|
|
|
|
|
|
|
| |
1. Add definition for iomem_valid_addr
2. Add definition for CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Wallace Wang <r59996@freescale.com>
|
|
|
|
|
|
|
|
| |
Both EVK and ARM2 board using the same machine id.
Currently, use system_rev to diff ARM2 board. DDR freq
for ARM2 has been set to 400M, but 300M on EVK.
Signed-off-by:Jason Liu <r64343@freescale.com>
|
|
|
|
|
|
| |
Build Mfg firmware for mx35 3stack
Signed-off-by: Wallace Wang <r59996@freescale.com>
|
|
|
|
|
|
|
| |
System can not find MMC/SD card in SD
slot 1 when booting from Uboot.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
| |
1. Remove board specific code in mxc_i2c.c.
2. Remove board specific code in mxc_fec.c.
3. Move imx_spi_nor.h to include/asm-arm.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Add mmu, l1cache, l2cache support for mx53.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
Add uboot support for MX53
Signed-off-by:Jason Liu <r64343@freescale.com>
|
|
|
|
|
|
| |
FEC not work in mx28 u-boot.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
| |
MX28 U-BOOT enhancements.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
|
|
|
|
|
|
|
| |
It was found that the failure is caused by
sending DCHP Discover request with empty
"Parameter Request List" option.
Signed-off-by: Terry Lv <r65388@freescale.com>
|