summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* serial_mx31: allow it to work with mx27 too and rename to serial_mxcIlya Yanok2009-06-21-4/+4
| | | | | | | UART hardware on i.MX27 is the same as on the i.MX31 so we just need to provide the driver with correct address of the registers. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* at91sam9263ek: add nor flash supportJean-Christophe PLAGNIOL-VILLARD2009-06-21-6/+136
| | | | | | this will allow you to store use it for the env and to boot directly U-Boot from Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: add support for the PM9261 board of Ronetix GmbHIlko Iliev2009-06-21-0/+382
| | | | | | | | | | The PM9261 board is based on the AT91SAM9261-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9261.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* pm9263: use macro instead of hardcode value for the lowlevel_initJean-Christophe PLAGNIOL-VILLARD2009-06-21-28/+81
| | | | | | | optimize a few the RAM init Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* pm9263: lowlevel init updateJean-Christophe PLAGNIOL-VILLARD2009-06-21-9/+1
| | | | | | | move PSRAM init to pm9263.c this will allow us after to make the nor lowlevel_init generic Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Blackfin: fix SPI flash speed define nameMike Frysinger2009-06-15-11/+11
| | | | | | | The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf548-ezkit: bump up monitor sizeMike Frysinger2009-06-15-1/+1
| | | | | | | The latest version of U-Boot got a bit fatter in the BSS section which caused overflows in the RAM region, so increase the monitor size. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf533-stamp/bf537-stamp: fix env settings for SPI flashVivi Li2009-06-15-4/+4
| | | | | | | | | The SPI flash layer is much stricter about sector usage than the eeprom layer we used to use, so update the env settings to better match the sector alignment of the flashes we use. Signed-off-by: Vivi Li <vivi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk2009-06-15-0/+8
|\
| * Convert DM9000 driver for CONFIG_NET_MULTIRemy Bohmer2009-06-15-0/+4
| | | | | | | | | | | | | | | | | | All drivers need to be converted to CONFIG_NET_MULTI. This patch converts the dm9000 driver. Signed-off-by: Thomas Smits <ts.smits@gmail.com> Signed-off-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * Switched davinci_emac Ethernet driver to use newer APIBen Warren2009-06-15-0/+4
| | | | | | | | | | | | | | | | Added CONFIG_NET_MULTI to all Davinci boards Removed all calls to Davinci network driver from board code Added cpu_eth_init() to cpu/arm926ejs/cpu.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* | Blackfin: unify u-boot linker scriptsMike Frysinger2009-06-14-0/+124
| | | | | | | | | | | | | | | | | | | | | | All the Blackfin linker scripts were duplicated across the board dirs with no difference save from the semi-often used ENV_IS_EMBEDDED option. So unify all of them in the lib_blackfin/ dir and for the few boards that need to embedded the environment directly, add a LDS_BOARD_TEXT define for them to customize via their board config file. This is much simpler than forcing them to duplicate the rest of the linker script. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf518f-ezbrd: enable SST SPI flash driverMike Frysinger2009-06-14-0/+1
| | | | | | | | | | | | | | The BF51xF parts have an internal SST SPI flash, so make sure the driver is enabled by default so we can access it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: convert specific pre/post config headers to common methodMike Frysinger2009-06-14-63/+22
| | | | | | | | | | | | | | | | | | | | The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup common Blackfin board defines. The common method now is to use config.h, so convert blackfin-config-post.h to that. Rename the still Blackfin specific blackfin-config-pre.h to config-pre.h so the naming conventions at least line up. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: enable LZMA for all ADI boardsMike Frysinger2009-06-14-0/+5
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: make default ADI env more flexibleMike Frysinger2009-06-14-5/+25
| | | | | | | | | | | | | | | | Allow boards to easily override the root= and default bootcmd, allow people to tweak the file used in default bootcmds at runtime via one env var, and add a stock nandboot command. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: ibf-dsp561: new board portHoan Hoang2009-06-14-0/+130
| | | | | | | | | | Signed-off-by: Hoan Hoang <hnhoan@i-syst.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: blackstamp: new board portMike Frysinger2009-06-14-0/+275
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-srv1: new board portMike Frysinger2009-06-14-0/+204
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-minotaur: new board portMike Frysinger2009-06-14-0/+204
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bf537-pnav: new board portMike Frysinger2009-06-14-0/+172
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf527: new board portMike Frysinger2009-06-14-0/+137
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf548: new board portMike Frysinger2009-06-14-0/+141
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: tcm-bf537: new board portMike Frysinger2009-06-14-0/+125
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf561: new board portMike Frysinger2009-06-14-0/+104
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf537e: new board portMike Frysinger2009-06-14-0/+124
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: cm-bf533: new board portMike Frysinger2009-06-14-0/+104
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: new spibootldr commandMike Frysinger2009-06-14-0/+1
|/ | | | | | | Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes, so add a new 'spibootldr' command to take advantage of it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 85xx: Add UEC6 and UEC8 at SGMII mode for MPC8569MDSHaiying Wang2009-06-12-0/+25
| | | | | | | | | On MPC8569MDS board, UCC6 and UCC8 can be configured to work at SGMII mode via UEM on PB board. Since MPC8569 supports up to 4 Gigabit Ethernet ports, we disable UEC6 and UEC8 by default. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add RMII support for MPC8569MDSHaiying Wang2009-06-12-4/+34
| | | | | | | | | This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to enalbe_mpc8569mds_qe_uec which is more accurate. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add UEC3 and UEC4 support for MPC8569MDSHaiying Wang2009-06-12-0/+23
| | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx: Add P2020DS supportSrikanth Srinivasan2009-06-12-0/+741
| | | | | | | | | | | | | The patch adds support for P2020DS reference platform. DDR3 interface uses hard-coded initialization rather than SPD for now and was tested at 667Mhz. Some PIXIS register definitions and associated code sections need to be fixed. TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all tested under u-boot. Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc512x: MPC5121ADS: Add NAND supportStefan Roese2009-06-12-1/+21
| | | | | | | | | | This patch adds NAND support to the MPC5121ADS board. Please note that the image size increased since NAND support didn't fit in the current image size (256k). Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Denk <wd@denx.de>
* mpc512x: Add esd gmbh mecp5123 board supportStefan Roese2009-06-12-0/+458
| | | | | | | MECP5123 is a MPC5121E based module by esd gmbh. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* 74xx_7xx: CPCI750: Add CPCI adapter/target supportStefan Roese2009-06-12-0/+2
| | | | | | | | The CPCI750 can be built as CPCI host or adapter/target board. This patch adds support for runtime detection of those variants. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* 74xx_7xx: CPCI750: Add commandline editing/historyStefan Roese2009-06-12-1/+2
| | | | | Signed-off-by: Stefan Roese <sr@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
* mpc85xx: 8536ds: Add USB related CONFIGsVivek Mahajan2009-06-12-2/+12
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8536ds and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc83xx: 8315erdb: Add USB related CONFIGsVivek Mahajan2009-06-12-1/+10
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8315erdb and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]xPeter Tyser2009-06-12-13/+13
| | | | | | | | Use the standard lowercase "x" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xxPeter Tyser2009-06-12-14/+14
| | | | | | | | Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MPC512x: add support for ARIA boardWolfgang Denk2009-06-12-0/+554
| | | | | | | ARIA is a MPC5121E based COM Express module by Dave/DENX. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* MPC512x: remove include/mpc512x.hWolfgang Denk2009-06-12-3/+3
| | | | | | | | | | | | | | | | | | | | Move needed definitions (register descriptions etc.) from include/mpc512x.h into include/asm-ppc/immap_512x.h. Instead of using a #define'd register offset, use a function that provides the PATA controller's base address. All the rest of include/mpc512x.h are register offset definitions which can be eliminated by proper use of C structures. There are only a few register offsets remaining that are needed in cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h which is intended as a temporary workaround only. In a later patch this file will be removed, too, and then auto-generated from the respective C structs. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* Rename ads5121 board into mpc5121adsWolfgang Denk2009-06-12-12/+12
| | | | | | | | | We rename the board so we use a consistent name in U-Boot and in Linux. Also, we use this opportunity to move the board into the Freecale vendor directory. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
* Add support for Linux-like kallsysmsMike Frysinger2009-06-12-1/+1
| | | | | | | The kernel stores address<->symbol names in it so things can be decoded at runtime. Do it in U-Boot, and we get nice symbol decoding when crashing. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* mtd: MTD related config header changes (mtdparts command)Stefan Roese2009-06-12-0/+66
| | | | | | | | | | | | | | | | | | | | | | | | | | By changing the cmd_mtdparts to only use the MTD infrastructure and not the direct interface to the CFI NOR FLASH driver we now need to add the MTD infrastructure to all boards using those mtdparts commands. This patch adds those components: CONFIG_MTD_DEVICE (for all FLASH types) plus CONFIG_FLASH_CFI_MTD (for NOR FLASH) To all board maintainers: Please test this on your platforms and report any problems/issues found. Thanks. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Ron Madrid <info@sheldoninst.com> Cc: Georg Schardt <schardt@team-ctech.de> Cc: Michal Simek <monstr@monstr.eu> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Martin Krause <martin.krause@tqs.de> Cc: Gary Jennejohn <garyj@denx.de> Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
* ZOOM2 Define GPIO banks used.Tom Rix2009-06-12-0/+8
| | | | | | | Enable the function and interface clocks for banks 2,3,5 and 6. Signed-off-by: Tom Rix <Tom.Rix@windriver.com> Acked-by: Dirk Behme <dirk.behme@googlemail.com>
* at91: move cpu info print to cpuJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: move cpu name define to arm/arch/ cpu headerJean-Christophe PLAGNIOL-VILLARD2009-06-12-8/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* OMAP3: Zoom2: Enable Board and CPU infoDirk Behme2009-06-12-0/+6
| | | | | | | | | With other OMAP3 boards we recently switched to CPU and Board info API. From parallel merge, this is missing for Zoom2. Enable it for Zoom2, too. Signed-off-by: Dirk Behme <dirk.behme@googlemail.com> Acked-by: Tom Rix <Tom.Rix@windriver.com>
* ZOOM2 Add led support.Tom Rix2009-06-12-0/+16
| | | | | | This patch controls the large LED on the top left of the zoom2. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
generated by cgit v1.1 at 2024-11-17 08:41:42 +0000