arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	Add GPL-2.0+ SPDX-License-Identifier to source files	Wolfgang Denk	2013-07-24	-17/+1
\| \| \| \| \| \|	Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
*	fpga: zynq: Add support for loading bitstream	Michal Simek	2013-05-06	-0/+6
\| \| \| \| \| \| \| \| \| \| \| \| \|	Devcfg device requires to load bitstream in binary format. But u-boot also has an option for loading bitstream in bit format. Let's handle both cases by zynqpl driver. Also add suport for loading partial bitstreams. The first driver version was done by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
*	i2c: zynq: Add support for Xilinx Zynq	Michal Simek	2013-04-30	-0/+11
\| \| \| \| \| \| \| \| \|	Support Xilinx Zynq i2c controller. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
*	mmc: Add support for Xilinx Zynq sdhci controller	Michal Simek	2013-04-30	-0/+16
\| \| \| \| \| \| \|	Add support for SD, MMC and eMMC card on Xilinx Zynq. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
*	net: gem: Pass phy address to init	David Andrey	2013-04-30	-0/+1
\| \| \| \| \| \| \| \| \|	Pass the PHY address to the driver init to allow parallel use of both interfaces Signed-off-by: David Andrey <david.andrey@netmodule.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
*	zynq: Move macros to hardware.h	Michal Simek	2013-04-30	-1/+1
\| \| \| \| \| \| \| \|	Add all fixed addresses to hardware.h and change petalinux configuration to support this. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
*	zynq: Move scutimer baseaddr to hardware.h	Michal Simek	2013-04-30	-3/+0
\| \| \| \| \| \| \| \|	Move baseaddr to hardware.h to be shared between configurations. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
*	xilinx: zynq: Enable DCC and create new zynq_dcc board	Michal Simek	2013-02-07	-0/+5
\| \| \| \| \| \|	Enable DCC driver for arm zynq platform to be compiled. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
*	serial: Remove CONFIG_SERIAL_MULTI from config files	Marek Vasut	2012-10-15	-1/+0
\| \| \| \| \| \| \| \| \| \| \| \| \|	Remove any notion of CONFIG_SERIAL_MULTI from board config files. Since CONFIG_SERIAL_MULTI is now enabled by default, it is useless to specify this config option in the board config files. Therefore remove it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
*	xilinx: Add new Zynq board	Michal Simek	2012-10-04	-0/+112
	Add support for Xilinx Zynq board. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Marek Vasut <marex@denx.de> CC: Joe Hershberger <joe.hershberger@gmail.com>