| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Walk the BIT and BCT to find the ODMDATA word in the
CustomerData field and put it into Scratch20 reg for
use by kernel, etc.
Built all Tegra builds OK; Booted on Seaboard and saw
ODMDATA in PMC scratch20 was the same as the value in my
burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities
will have to specify the odmdata (nvflash --odmdata n) on
the command line or via a cfg file, or built in to their
BCT.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
| |
|
|
|
|
|
|
| |
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Store the environment in eMMC, at the end of the second boot sector.
This should not conflict with any other eMMC usage: U-Boot is stored
well below this location, and the kernel only uses the general area
of the eMMC once booted, not the boot sectors.
Note: This assumes the user plugged the standard 8MB MoviNAND card into
J29/HSMMC/POP. If they didn't, the boot sector layout may be different.
However, use of that particular card is standard practice as far as I
know.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The SMSC95xx series may exist either directly on a main board, or as a USB
to Ethernet dongle. However, dongles containing these chips are very rare.
Hence, remove this config option, except on Harmony where such a chip is
actually present on the board.
The asix option remains, since it's a popular chip, and I actively use a
dongle containing this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
| |
|
|
|
|
|
|
|
| |
CONFIG_CMD_PING/NFS aren't required for Whistler to boot.
Add some comments.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This implements a useful bootcmd for Tegra. The boot order is:
* If USB enabled, USB storage
* Internal MMC (SD card or eMMC)
* If networking is enabled, BOOTP/TFTP
When booting from USB or MMC, the boot script is assumed to be in
partition 1 (although this may be overridden via the rootpart variable),
both ext2 and FAT filesystems are supported, the boot script may exist
in either / or /boot, and the boot script may be named boot.scr.uimg or
boot.scr.
When booting over the network, it is assumed that boot.scr.uimg exists
on the TFTP server. There is less flexibility here since those setting
up network booting are expected to need less hand-holding.
In all cases, it is expected that the initial file loaded is a U-Boot
image containing a script that will load the kernel, load any required
initrd, load any required DTB, and finally bootm the kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
console isn't used by anything, and the kernel should be set appropriately
by whatever script is booting the kernel, not imposed by the bootloader.
mem might be useful, but the current value is pretty bogus, since it
includes nvmem options that make no sense for an upstream kernel, and
equally should not be required for any downstream kernel. Either way, this
is also best left to the kernel boot script.
smpflag isn't used by anything, and again was probably intended to be a
kernel command-line option better set by the kernel boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
|
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
