summaryrefslogtreecommitdiff
path: root/include/configs/sunxi-common.h
Commit message (Collapse)AuthorAgeLines
* sunxi: Enable pre-console bufferSiarhei Siamashka2015-01-14-0/+6
| | | | | | | | This allows to always have a complete log on the VGA/HDMI/LCD console. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: sunxi-common.h: Reduce bootm_size to take the framebuffer into accountHans de Goede2015-01-14-3/+6
| | | | | | | | | | Before video output support can be enabled on the A13-OLinuXinoM, bootm_size must first be reduced to take into account that the framebuffer is shaved of the top of the DRAM. For other boards this is not an issue since bootm was set to 256M and all boards have at least 512M except for the A13-OLinuXinoM. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: video: Add DDC & EDID supportHans de Goede2015-01-14-0/+1
| | | | | | | | | | Add DDC & EDID support and use it to automatically select the native mode of the attached monitor. This can be disabled by adding edid=0 as option to the video-mode env. variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* sunxi: video: Add support for video-mode environment variableHans de Goede2015-01-14-1/+1
| | | | | | | | | | | | | | | | Add support for the standard video-mode environment variable using the videomodes.c video_get_ctfb_res_modes() helper function. This will allow users to specify the resolution e.g. : setenv video-mode sunxi:video-mode=1280x1024-24@60 saveenv Also make the reserved fb mem slightly larger to allow 1920x1200 to work. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* sunxi: video: Use video-mode/-timing from videomodesHans de Goede2015-01-14-0/+1
| | | | | | | | | Switch from fb_videomode to ctfb_res_modes and use the predefined videotimings from videomodes.c, rather then defining our own. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Anatolij Gustschin <agust@denx.de>
* sunxi: Fix CONFIG_UART0_PORT_F build and add it to menuconfigSiarhei Siamashka2015-01-14-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | The CONFIG_UART0_PORT_F option has been supported since http://git.denx.de/?p=u-boot.git;a=commit;h=ff2b47f6a9cc1025 This option is primarily useful only for low level u-boot debugging on tablets, where normal UART0 is difficult to access and requires device disassembly and/or soldering. This patch now allows it to be selected from menuconfig. A dependency on SPL_FEL is added because u-boot does not support booting from NAND yet and also booting from SD card is impossible when a MicroSD breakout board is plugged into the SD slot. Additionally a compilation problem is fixed: common/spl/built-in.o: In function `spl_mmc_load_image': /tmp/u-boot-sunxi/common/spl/spl_mmc.c:94: undefined reference to `mmc_initialize' /tmp/u-boot-sunxi/common/spl/spl_mmc.c:96: undefined reference to `find_mmc_device' /tmp/u-boot-sunxi/common/spl/spl_mmc.c:104: undefined reference to `mmc_init' scripts/Makefile.spl:206: recipe for target 'spl/u-boot-spl' failed Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add usb keyboard Kconfig optionHans de Goede2014-11-25-0/+13
| | | | | | | For use together with the hdmi console. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ian.campbell@citrix.com>
* sunxi: video: Add simplefb supportLuc Verhaegen2014-11-25-0/+8
| | | | | | | | | | | | Add simplefb support, note this depends on the kernel having support for the clocks property which has recently been added to the simplefb devicetree binding. Signed-off-by: Luc Verhaegen <libv@skynet.be> [hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as disussed on the devicetree list] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>.
* sunxi: video: Add cfb console driver for sunxiLuc Verhaegen2014-11-25-0/+41
| | | | | | | | | | | | | | | | | | | | | | | | This adds a fixed mode hdmi driver for the sunxi platform. The fixed mode is a relatively safe 1024x768, more complete EDID handling is currently not provided. Only HDMI is supported today. This code is enabled when HPD detects an attached monitor. Current config is such that 8MB is shaved off at the top of the RAM. This avoids several memory handling issues, most significant is the fact that on linux on ARM you are not allowed to remap known RAM as IO. A clued in display driver will be able to recycle this reserved RAM in future though. cfbconsole was chosen as it provides the most important functionality: a working u-boot console, allowing for the debugging of certain issues without the need for a UART. Signed-off-by: Luc Verhaegen <libv@skynet.be> [hdegoede@redhat.com: Major cleanups and some small bugfixes] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* dm: sunxi: Add support for serial using driver modelSimon Glass2014-11-05-6/+11
| | | | | | | | | | Add a driver for the designware serial UART used on sunxi. This just redirects to the normal ns16550 driver. Add a stdout-path to the device tree so that the correct UART is chosen. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* dm: sunxi: Modify the GPIO driver to support driver modelSimon Glass2014-11-05-0/+1
| | | | | | | | | This adds driver model support to the sunxi GPIO driver, using the device tree to trigger binding of the driver. The driver will still operate without driver model too. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* dm: sunxi: Add a new config for an FDT-based pcDuino3Simon Glass2014-11-05-0/+4
| | | | | | | | | For now we won't want to mess with the existing configurations. Create a new one which will enable device tree and driver model. Note that this brings the device tree binary into u-boot-sunxi-with-spl.bin. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Increase command line buffer size (CONFIG_SYS_CBSIZE)Ian Campbell2014-10-24-2/+2
| | | | | | | | | | I was running into this limit with a not overly long PXE append line. Since the PXE code wants to print the resulting command line increase CONFIG_SYS_PBSIZE too. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
* ARM: sunxi: Add support for using R_UART as consoleChen-Yu Tsai2014-10-24-0/+1
| | | | | | | | | | The A23 only has UART0 muxed with MMC0. Some of the boards we encountered expose R_UART as a set of pads. Add support for R_UART so we can have a console while using mmc. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: sunxi: Add support for uart0 on port F (mmc0)Chen-Yu Tsai2014-10-24-0/+2
| | | | | | | | | Allwinner SoCs provide uart0 muxed with mmc0, which can then be used with a micro SD breakout board. On the A23, this is the only way to use uart0. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: sunxi: Fix build break when CONFIG_MMC is not definedChen-Yu Tsai2014-10-24-1/+7
| | | | | | | | | | | | BOOT_TARGET_DEVICES includes MMC unconditionally. This breaks when CONFIG_CMD_MMC is not defined. Use a secondary macro to conditionally include it when CONFIG_MMC is enabled, as we do for CONFIG_AHCI. This is used when we want to use uart0 from port F, which conflicts with mmc0. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add mmc card-detect functionalityHans de Goede2014-10-24-0/+1
| | | | | Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: sunxi: Fix build break when CONFIG_USB_EHCI is not definedChen-Yu Tsai2014-10-24-1/+7
| | | | | | | | | BOOT_TARGET_DEVICES includes USB unconditionally. This breaks when CONFIG_CMD_USB is not defined. Use a secondary macro to conditionally include it when CONFIG_EHCI is enabled, as we do for CONFIG_AHCI. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* kconfig: move CONFIG_SYS_HZ to lib/KconfigMasahiro Yamada2014-10-23-2/+0
| | | | | | | | | | | | CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h (but some boards still have redundant definitions). This commit moves the definition and the document in README to Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000, the sanity check in lib/time.c should be removed. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Marek Vasut <marex@denx.de>
* sunxi: Correct typo CONFIG_FTDFILE => CONFIG_FDTFILEIan Campbell2014-09-05-1/+1
| | | | | | | | | | | | Patch is the result of: sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig Reported-by: Vagrant Cascadian <vagrant@debian.org> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> [ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
* sunxi: Add environment settings to make extlinux.conf booting workHans de Goede2014-08-12-3/+15
| | | | | | | | | | | | Automatic booting using an extlinux.conf file requires various environment variables to be set. Also modify CONFIG_SYS_LOAD_ADDR and CONFIG_STANDALONE_LOAD_ADDR to match the value chosen for kernel_addr_r, see the added comment for why the new value is chosen. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Stephen Warren <swarren@nvidia.com>
* sunxi-common.h: Use new generic $bootcmdHans de Goede2014-08-12-3/+22
| | | | | | | Use the new standard bootcmd from <config_distro_bootcmd.h>. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Stephen Warren <swarren@nvidia.com>
* sunxi-common.h: Don't undef CONFIG_CMD_NET only to redefine it again laterHans de Goede2014-08-12-3/+1
| | | | | | | | | | | | config_distro_defaults.h which is include later will redefine CONFIG_CMD_NET, drop the useless / meaningless undef of it. While at also move the undef of CONFIG_CMD_FPGA up to directly under the include of config_cmd_defaults.h, to make it clear that it overwrites the setting done from config_cmd_defaults.h . Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi-common.h: Don't undefine CONFIG_CMD_NFSHans de Goede2014-08-12-1/+0
| | | | | | | | I see no reason to override the choice to include this from config_cmd_defauls.h . Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi-common.h: Remove dead #ifdef CONFIG_CMD_NET code blockHans de Goede2014-08-12-8/+0
| | | | | | | | | We undef CONFIG_CMD_NET at line 167, and there is nothing re-defining it between line 167 and the #ifdef CONFIG_CMD_NET, so remove this effectively dead block. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi-common.h: Remove CONFIG_SYS_BOOT_GET_CMDLINEHans de Goede2014-08-12-2/+0
| | | | | | | | sunxi does not need this and it should never have been enabled for it in the first place. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: add general USB settingsRoman Byshko2014-07-31-0/+6
| | | | | | | | | | General configuration settings to be set if CONFIG_USB_EHCI is enabled for an Allwinner aka sunxi SoC. Signed-off-by: Roman Byshko <rbyshko@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* ahci: provide sunxi SATA driver using AHCI platform frameworkIan Campbell2014-07-31-0/+12
| | | | | | | | | | | | | | | | | | | | | This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done for sun7i only since I don't have access to any other sunxi platforms with sata included. The PHY setup is derived from the Alwinner releases and Linux, but is mostly undocumented. The Allwinner AHCI controller also requires some magic (and, again, undocumented) DMA initialisation when starting a port. This is added under a suitable ifdef. This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on contents of Linux DTS files, including SATA power pin config taken from the DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* include: remove CONFIG_SPL/CONFIG_TPL definition in config headersMasahiro Yamada2014-07-30-1/+0
| | | | | | | | | Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig. Remove the redundant definition in config headers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* include: define CONFIG_SPL and CONFIG_TPL as 1Masahiro Yamada2014-07-30-1/+1
| | | | | | | | | | | | | | | | We are about to switch to Kconfig in the next commit. But there are something to get done beforehand. In Kconfig, include/generated/autoconf.h defines boolean CONFIG macros as 1. CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1. Otherwise, when switching to Kconfig, the build log would be sprinkled with warning messages like this: warning: "CONFIG_SPL" redefined [enabled by default] Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* sunxi: add gpio driverIan Campbell2014-07-18-0/+4
| | | | | | | | | | | | | | | This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well as providing the common gpio API (gpio_request/free, direction in/out, get/set etc). Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ma Haijun <mahaijuns@gmail.com> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Henrik Nordström <henrik@henriknordstrom.net> Cc: Tom Cubie <Mr.hipboi@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: use random parts of SID to set ethaddrJonathan Liu2014-07-18-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Similar to the USB NIC found on OMAP5uEVM, PandaBoard and BeagleBoard-XM boards, the sunxi SoCs have a NIC onboard without an embedded MAC address. Just like the omap used on these boards, the sunxi SoCs do have a unique chip id, in the form of the 128 bit SID register: http://linux-sunxi.org/SID_Register_Guide So mimick the BeagleBoard-XM board code (commit 548a64d8) and use the chip id to generate a unique fixed MAC address. We check for the SID not being all 0, since some early A20 batches shipped without having there SID programmed. Note we use specific parts of the 128 bits, since some parts indicate the SoC family / revision, and thus are fixed. The algorithm for this was taken from the linux-sunxi.org kernels. Signed-off-by: Jonathan Liu <net147@gmail.com> [hdegoede@redhat.com: Expanded the commit message with some more info] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add axp209 pmic supportHenrik Nordstrom2014-07-18-0/+5
| | | | | | | | | | | Add support for the x-powers axp209 pmic which is found on most A10, A13 and A20 boards. And enable AXP209 support for the Cubietruck and Cubieboard boards. Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add i2c supportHans de Goede2014-07-18-0/+8
| | | | | | | | | | | | | Add support for the i2c controller found on all Allwinner sunxi SoCs, this is the same controller as found on the Marvell orion5x and kirkwood SoC families, with a slightly different register layout, so this patch uses the existing mvtwsi code. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-By: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Heiko Schocher <hs@denx.de> [ ijc -- updated u-boot-spl-fel.lds ]
* sunxi: Add emac glue, enable emac on the cubieboardHans de Goede2014-07-06-0/+5
| | | | | Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add sun5i supportHans de Goede2014-07-06-0/+2
| | | | | | | | | | | | | | | | | | | Add support for the Allwinner A13 and A10s SoCs also know as the Allwinner sun5i family, and the A13-OLinuXinoM A13 based and r7-tv-dongle A10s based boards. The only differences compared to the already supported sun4i and sun7i families are all in the DRAM controller initialization: -Different hcpr values -Different MBUS settings -Some other small initialization changes Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Remove mmc DMA supportHans de Goede2014-07-06-1/+0
| | | | | | | | | | | | | | | | The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the dma descriptors on the stack, and then exits while the dma transfer is in progress, so the dma engine is reading stack memory which at that point may be re-used. So far we've gotten away with this by luck, but recent u-boot changes have shifted the stack start address by 16 bytes, which combined with dma alignment now exposes this problem. Since we end up just busy waiting for the dma engine anyway, this commit fixes things by simply removing the dma code, resulting in smaller bug-free code. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: non-FEL SPL boot support for sun7iIan Campbell2014-05-25-0/+26
| | | | | | | | | | | Add support for booting from an MMC card. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
* sunxi: mmc supportIan Campbell2014-05-25-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote: > > + case 1: > > +#if CONFIG_MMC1_PG > Are you sure that this is correct and shouldn't be: > > +#ifdef CONFIG_MMC1_PG > > ? It's "correct" in so far as it works (the boards.cfg config stuff #defines things to 1), but I think you are right that it isn't the preferred style. But... > A quick scan through this patch series shows that this define > is not set at all. Perhaps its outdated? Or is it used to support > some other sunxi SoC? Not sure, perhaps it should be removed for > now. ...I had thought that it was to support some other board which wasn't being upstreamed right now, so eventually useful and harmless for now, but I've just checked and it isn't actually used by any of the boards in u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it. Rather than resend the entire series, here is v5.1 of this patch. > Other than this please add my: > > Reviewed-by: Stefan Roese <sr@denx.de> Thanks! 8<--------------------------------- >From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001 From: Ian Campbell <ijc@hellion.org.uk> Date: Fri, 7 Mar 2014 04:29:39 +0000 Subject: [PATCH v5.1 7/8] sunxi: mmc support This adds support for the MMC controller on the Allwinner A20 (sun7i) processor. Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Cc: Aaron Maoye <leafy.myeh@allwinnertech.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: Tom Rini <trini@ti.com>
* sunxi: add gmac Ethernet supportIan Campbell2014-05-25-0/+17
| | | | | | | | | | | Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i) processors. Enable for the Cubietruck. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@ti.com>
* sunxi: add sun7i cpu, board and start of day supportIan Campbell2014-05-25-0/+141
This patch adds generic board, start of day and basic build system support for the Allwinner A20 (sun7i) processor. This code will not been compiled until the build is hooked up in a later patch. It has been split out to keep the patches manageable. Signed-off-by: Adam Sampson <ats@offog.org> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luc Verhaegen <libv@skynet.be> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Patrick Wood <patrickhwood@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>