| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
| |
SPI NOR flash(m25p32-vmw6tg) not probed and function as expected, this
due to the lack of iomux pad config and incorrect CS line.
This patch fix the above issue and also fix the mfg config file
(For the code readable, I intent to omit the following checkpatch warning:
in the iomux/mx6_pins.h WARNING: line over 80 characters)
Signed-off-by: Jason Liu <r64343@freescale.com>
|
| |
|
|
|
|
|
|
| |
- i.mx6q sabresd revA ethernet phy addr is 0 (PHYADDRESS1-PHYADDRESS0:00)
, but revB ethernet phy address is 0x1 (PHYADDRESS1-PHYADDRESS0:01).
To avoid to change hardware, add auto discover phy address configuration.
Signed-off-by: Fugang Duan <B38611@freescale.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
dd read and change voltage support for mx6.
For help, pls type "help regul"
Detail command info:
regul list - List all regulators' name
regul show all - Display all regulators' voltage
regul show core - Show core voltage in mV
regul show periph - Show peripheral voltage in mV
regul show <regulator name> - Show regulator's voltage in mV
regul set core <voltage value> - Set core voltage in mV
regul set periph <voltage value> - Set periph voltage in mV
regul set <regulator name> <voltage value> - Set regulator's voltage in
mV
Example:
MX6Q ARM2 U-Boot > regul list
Name Voltage
vddpu
vddcore
vddsoc
vdd2p5
vdd1p1
vdd3p0
MX6Q ARM2 U-Boot > regul show all
Name Voltage
vddpu 1100000
vddcore 1100000
vddsoc 1200000
vdd2p5 2400000
vdd1p1 1100000
vdd3p0 3000000
MX6Q ARM2 U-Boot > regul show periph
Name Voltage
periph: 1100000
MX6Q ARM2 U-Boot > regul show core
Name Voltage
core: 1100000
MX6Q ARM2 U-Boot > regul set core 1100000
Set voltage succeed!
Name Voltage
core: 1100000
Signed-off-by: Terry Lv <r65388@freescale.com>
|
| |
|
|
|
|
|
|
|
|
| |
enable mfg profile.
enable recovery mode.
mx6q_sabresd board's usb otg have HW issue, disable it in
android profile.
Signed-off-by: Zhang Jiejing <jiejing.zhang@freescale.com>
|
| |
|
|
|
|
|
| |
Move partition command from nand to sata in mx6 for nand don't need
these partition command.
Signed-off-by: Terry Lv <r65388@freescale.com>
|
| |
|
|
|
|
|
| |
For ARM2 and Sabreauto, change TTY0 to TTY3 (which is physical UART4)
For SabreSD, Change TTY3 to TTY0 (which is physical UART1)
Signed-off-by: Eric Sun <jian.sun@freescale.com>
|
|
|
Add suport for i.MX 6Quad SABRE Smart Device.
Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com>
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
|
