summaryrefslogtreecommitdiff
path: root/include/configs/mx53_ard.h
Commit message (Collapse)AuthorAgeLines
* ENGR00157468: Fix default environment's "mmc dev" type errorTerry Lv2011-09-23-1/+1
| | | | | | | Some semicolons are missed after "mmc dev 0". They need to be added to make default environment work. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154666-1: Align u-boot mmc command with communityTerry Lv2011-09-01-3/+2
| | | | | | | | Modifications on config files. 1. Remove CONFIG_BOOT_PARTITION_ACCESS. 2. Change all mmc read command in default env configs. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00154396: U_BOOT: Env config adjustment.Terry Lv2011-08-12-3/+3
| | | | | | | Change env size to 8K and change gpmi nand env offset to 2M. This will reduce boot time and fix gpmi nand env problem. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00143570 mx53: change the default environment settingLily Zhang2011-05-19-2/+3
| | | | | | | Change the default environment setting as sd boot for mx53 loco, mx53 smd and mx53 ard boards. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00139120: Correct CONFIG_CMD_MMC to CONFIG_CMD_IIM for iimTerry Lv2011-02-14-1/+1
| | | | | | Correct CONFIG_CMD_MMC to CONFIG_CMD_IIM for iim. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00138534 Disable splashimage support defaultly for PDKLiu Ying2011-01-26-1/+0
| | | | | | | Disable splashimage support defaultly for MX51 BBG/MX53 SMD/ MX53 ARD platforms. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138468-2 Enable splashimage support for several platformsLiu Ying2011-01-25-0/+1
| | | | | | | This patch enables splashimage support for MX53 SMD/ARD and MX51 BBG pdk platforms. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00138240 Disable splashimage support for PDKLiu Ying2011-01-20-1/+0
| | | | | | | Disable splashimage support for mx53 smd, mx53 ard and mx51 bbg. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137894-5 MX53 ARD:Support splashimageLiu Ying2011-01-14-0/+23
| | | | | | | | | | | This patch supports to use pwm wave to control backlight. The pwm rate is 200Hz and the pwm duty is 50%. Use 'lvds_num' env variable to choose to use lvds0 or lvds1. Note that you need to add 'splashimage' env variable to set the memory address of the bmp image. Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
* ENGR00137358: Add saving environment to sata device supportTerry Lv2011-01-11-1/+6
| | | | | | Add saving environment to sata device support. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00137372 MX53: Switch back to use DCD and update DDR scriptsLily Zhang2010-12-28-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. This patch is used to switch back to use DCD for flash header instead of plug-in. This change request is due to the following reasons: 1) U-boot community doesn't accept current plug-in solution when upstreaming. 2) Plug-in isn't supported by MX53 ROM serial download mode. No effective workaround is found now. To use the same code base to support normal U-Boot and MFG tool better, adopt DCD solution firstly. 3) Current MX53 DDR scripts don't exceed the length limitation of DCD. For MX53 TO2.0 EVK/ARM2 board, raise DDR frequency to 400MHZ after VCC and VDDA voltages are raised as 1.3V. Since ARM2 CPU2 board share the same script with EVK, delete ARM2 CPU2 config files. ARM2 CPU2 board can share the same bootloader with EVK. 2. Update MX53 DDR2 scripts for TO1.0/TO2.0 EVK/ARD/ARM2 boards The script "MX53_TO2_DDR2_EVK_ARD.inc" is located under http://compass.freescale.net/livelink/livelink? func=ll&objId=221058910&objAction=browse&viewType=1 This script is published by ATX and FIL team on Dec 16th, 2010 3. Update MX53 ARM2 CPU3 DDR3 script "MX53_TO2_DDR3_CPU3.inc" under the same compass folder Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00134220-2 Need use CONFIG_SYS_NAND_MAX_CHIPSJason Liu2010-12-07-1/+1
| | | | | | | Need use CONFIG_SYS_NAND_MAX_CHIPS instead of NAND_MAX_CHIPS Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00132909 MX53 Uboot: Support for TO2Anish Trivedi2010-11-15-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support new DDR script entitled "Rita_TO2_init_DDR2_CPU2_CMOS_TEST_CAL_v1.inc" for DDR2 boards including MX53 EVK, ARD, and ARM2 CPU2. These new settings did not apply to TO1. Therefore, changed the DCD for these boards to a plugin so that TO1 and TO2 can both be supported using conditional execution of new DDR settings. During bootup on TO2, DDR frequency is required to be below 400 MHz. Therefore, BOOT_CFG2[4] must be set to enable DDR at 333 MHz in ROM on all boards. Uboot determines silicon version and for TO2 boosts the VCC and VDDA voltages to 1.3V, after which the DDR frequency is also increased to 400 MHz. This requirement meant that uboot does not calibrate PLL2 anymore until the voltage is increased. Removed the calibration from lowlevel_init.S and from all mx53 include/configs files. Also required that during config_periph_clk(), only CBCMR register is touched to set source PLL. Other changes to CBCDR were removed. Switching to PLL2 bypass clk during reprogram was also removed. All these changes are required to increase DDR frequency to 400 MHz. DDR2 CPU2 board with TO1 requires the following hw cfgs: JP3 populated, and J8 set to 2-3. For DDR2 CPU2 board with TO2, both these jumpers should be depopulated. ARM2 CPU3 (with DDR3) DDR configurations were not changed. TO1 and TO2 can run well using existing DDR3 script. However, DCD was converted to plugin to align with other boards. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00132759 MX53: use 32K CLK as GPT sourceLily Zhang2010-10-19-0/+1
| | | | | | | | | | | | | MT29F16G08MAA NAND flash was failed on MX53 ARD/RevB board, but it's fine in RevA board. After check, it's found that udelay is not accurate on MX53 ARD/RevB board because GPT uses IPG peripheral clock and assume it is 50MHZ. However IPG peripheral clock is not 50MHZ in MX53 ARD/RevB board. So it causes udelay is not accurate. This patch changes GPT clk source as 32K to make udelay accurate. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00132617 MX53: add NAND supportLily Zhang2010-10-17-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | Add NAND support for MX53 EVK and ARD. Need to use kobs-ng to flash U-Boot on MX53 TO1. Because MX51 TO1 ROM doesn't support bi swap solution and kernel enable bi swap, Must enable "ignore bad block" option when flashing U-Boot. The step is as following: echo 1 > /sys/devices/platform/mxc_nandv2_flash.0/ignorebad kobs-ng init --chip_0_device_path=/dev/mtd2 u-boot.bin echo 0 > /sys/devices/platform/mxc_nandv2_flash.0/ignorebad Since default configuration stores environment into SD card and U-Boot uses get_mmc_env_devno (Read SBMR register) to get MMC/SD slot information, you must insert SD card to bottom SD slot to get/store environment if you are using NAND boot on MX53 EVK. You must config boot dip setting well when doing NAND boot. For example, if you are using NAND 29F32G080AA NAND chip on MX53 EVK, you can set boot dips as the following for NAND boot: SW3: dip 7, 8 on; SW2: dip 3,5 on; SW1: dip 4,7,8 on. Other dips are off. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00131840 MX53 ARD:use serial_mxc as uart driverLily Zhang2010-09-22-2/+2
| | | | | | | Use serial_mxc as uart driver for MX53 ARD. This change is required by ENGR00131779. Signed-off-by: Lily Zhang <r58066@freescale.com>
* ENGR00131705-2 Add MX53 ARD supportLily Zhang2010-09-20-0/+269
Add MX53 Automotive Reference Board (ARD) support 1. Add DDR2 initialization script 2. Add external ethernet support 3. Update PIN settings for UART, I2C, SDHC etc Signed-off-by: Anish Trivedi <anish@freescale.com> Signed-off-by: Terry Lv <r65388@freescale.com> Signed-off-by: Lily Zhang <r58066@freescale.com>
generated by cgit v1.1 at 2024-11-22 14:54:01 +0000