summaryrefslogtreecommitdiff
path: root/include/configs/maxbcm.h
Commit message (Collapse)AuthorAgeLines
* arm: mvebu: Move SoC selection (A38X vs AXP) into KconfigStefan Roese2016-01-14-2/+0
| | | | | | | | | | | | | | | | | | Until now, the SoC selection for the ARCH_MVEBU platforms has been done in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As it needed to get selected for AXP and A38x based boards. This patch now changes this to move the SoC selection to Kconfig. And also uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x. This makes things a bit clearer - especially for new board additions. Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available CONFIG_ARMADA_38X and CONFIG_ARMADA_XP. And CONFIG_DDR3 is removed, as its not referenced anywhere. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: Make ECC support configurable on Armada XPStefan Roese2016-01-14-0/+1
| | | | | | | | | | | Currently, ECC support is enabled for all Armada XP boards. So the DDR3 driver tries to configure the controller with ECC support, even on boards without ECC. This patch makes this ECC optional which now can be configured on a board-per-board basis. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Phil Sutter <phil@nwl.cc>
* arm: mvebu: Move some defines to common include fileStefan Roese2016-01-14-3/+0
| | | | | | | | | This patch moves some config options to the mvebu common include file. Making it easier to not forget these defines for new boards. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
* net: mvneta: Convert to driver modelStefan Roese2016-01-14-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Update this driver to support driver model. As all MVEBU boards using this driver are converted with this patch, the non-driver-model code can be removed completely. This is also the reason why this patch is quite big and includes a) the driver change and b) the platform change. As its not git-bisect save otherwise. With this conversion, some parameters are now extracted from the DT instread of using the config header defines. The supported properties right now are: PHY-mode ("phy-mode") and PHY-address ("reg"). The base addresses for the ethernet controllers can be removed from the header files as well. Please note that this patch also removes the E1000 network driver from some MVEBU config headers. This is necessary, as with DM_ETH configured and the e1000 driver enabled, the PCI driver also needs to support DM. But the MVEBU PCI(e) driver still needs to get ported to DM. When this is done, the E1000 driver can be enabled again. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Simon Glass <sjg@chromium.org>
* arm: mvebu: Add DM and OF_CONTROL support to SPLStefan Roese2016-01-14-3/+3
| | | | | | | | | | | | | | | | | | | | | | This patch adds full DM support to the SPL on MVEBU. Currently only serial is supported. Other drivers will follow. This patch also adds the necessary config values for the DEBUG UART to the MVEBU defconfig files. This came in handy while implementing this DM support. Additionally, the mvebu specific SPL linker script is removed and this common one is used instead: arch/arm/cpu/u-boot-spl.lds This common linker script already handles all special cases. No need to reinvent the wheel for MVEBU here. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Simon Glass <sjg@chromium.org>
* sf: Move SPI flash drivers to defconfigBin Meng2015-11-25-2/+0
| | | | | | | | There are already Kconfig options for SPI flash drivers, but we have not moved them from config.h to defconfig files. This commit does this in a batch. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
* arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada2015-10-24-1/+0
| | | | | | | | | | | We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* arm: mvebu: Only set CONFIG_SKIP_LOWLEVEL_INIT for SPLStefan Roese2015-10-21-0/+2
| | | | | | | | | When running on the AXP I sometimes noticed a strange behavior. As some characters are not echoed on the U-Boot prompt. Not disabling the lowlevel_init code, especially calling cpu_init_cp15() in the main U-Boot seems to solve this issue. Signed-off-by: Stefan Roese <sr@denx.de>
* arm: mvebu: Move CONFIG_SYS_TEXT_BASE to an address < 16 MiBStefan Roese2015-08-17-1/+6
| | | | | | | | | | | | | | | This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada XP / 38x boards in mainline U-Boot. This is done in preparation for the ECC SDRAM scrubbing that needs to be done in the main U-Boot. The SPL (previously bin_hdr) has already scrubbed the area: 0x0000.0000 - 0x0100.0000 In this area this main U-Boot needs to get loaded. The main U-Boot then can scrub the remaining SDRAM area while running from this location. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: drivers/ddr: Move Armada XP DDR init code into new directoryStefan Roese2015-07-23-1/+1
| | | | | | | | | | | | | | | | With the upcoming addition of the Armada 38x DDR support, which is not compatible to the Armada XP DDR init code, we need to introduce a new directory infrastructure. To support multiple Marvell DDR controller. This will be the new structure: drivers/ddr/marvell/axp Supporting Armada XP (AXP) devices (and perhaps Armada 370) drivers/ddr/marvell/a38x Supporting Armada 38x devices (and perhaps Armada 39x) Signed-off-by: Stefan Roese <sr@denx.de>
* defconfig: Move CONFIG_SPI_FLASH_BAR from configsJagan Teki2015-07-01-1/+0
| | | | | | | | | This commit moves: - CONFIG_SPI_FLASH_BAR from include/configs/*.h into configs/*_defconfigs Signed-off-by: Jagan Teki <jteki@openedev.com>
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-25-1/+0
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* arm: mvebu: Change network init code to allow a more flexible setupStefan Roese2015-05-05-1/+1
| | | | | | | | | | | | | | | With the introduction of the Armada 38x support, its necessary to change the mvneta ethernet driver init call from always 4 times to a configurable value. Lets make this init call more flexible by moving the actually used devices to the config header. Additionally this patch takes care of the slightly different base addresses for the ethernet controllers on A38x. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* arm: mvebu: Move CONFIG_SPL_LDSCRIPT to common headerStefan Roese2015-05-05-1/+0
| | | | | | | | | This way, new MVEBU boards don't need to specifiy the common location for the SPL linker script. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* arm: mvebu: Move mvebu-common into mach-mvebuStefan Roese2015-05-05-1/+1
| | | | | | | | | | Now that the mach-mvebu directory exists and is used by Armada XP we can move the mvebu-common files into this directory as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
* i2c: mvtwsi: Support for up to 4 different controllersPaul Kocialkowski2015-04-15-1/+1
| | | | | | | | | | | | Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI controller. However, other platforms using MVTWSI may come with more: this is the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found on the same chip. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* arm: mvebu: maxbcm: Fix compilation warning and add Spansion SPI NOR supportStefan Roese2015-02-06-0/+2
| | | | | | | | | | | | | | | | | | | | | This patch fixes the following compilation warning for maxbcm: Building maxbcm board... text data bss dec hex filename 160075 6596 38240 204911 3206f ./u-boot board/maxbcm/maxbcm.c: In function 'reset_phy': board/maxbcm/maxbcm.c:68:6: warning: unused variable 'reg' [-Wunused-variable] u16 reg; ^ board/maxbcm/maxbcm.c:66:6: warning: unused variable 'devadr' [-Wunused-variable] u16 devadr = CONFIG_PHY_BASE_ADDR; ^ Additionally support Spansion SPI NOR flash is added. With larger SPI device support via the CONFIG_SPI_FLASH_BAR define. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
* arm: maxbcm: Enable SPL to include DDR training code into U-BootStefan Roese2015-02-06-0/+47
| | | | | | | | | This patch adds SPL support to the maxbcm MV78460 based board. Including the fixed DDR configuratrion needed for the DDR training code. And the the serdes PHY init code. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
* arm: armada-xp: Add basic support for the maxBCM boardStefan Roese2014-10-23-0/+68
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It integrates an SPI NOR flash and an Marvell 88E6185 switch. Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit v1.1 at 2024-11-09 07:14:19 +0000