summaryrefslogtreecommitdiff
path: root/include/configs/km
Commit message (Collapse)AuthorAgeLines
* arm/km: remove calls to kw_gpio_* in board_early_init_fHolger Brunck2012-07-07-0/+1
| | | | | | | | | | | | | | | | | | | | These functions tried to access two static tables before relocation (board_early_init_f is executed before relocation). But these static tables lie in the bss section which is not valid before relocation. These accesses then overwrote some parts of u-boot binary before it was relocated. For the kmnusa build, this results in a corrupted important env variable (bootcmd) but it may be that some other parts of the u-boot binary are corrupted. This patch solves this problem by moving all the kw_gpio_* calls to board_init, which should be early enough in the boot sequence. The only calls that could not be moved is the one for the SOFT (bitbang) I2C, and they have been replaced by a direct access to the GPIO dataout Control register to set the two GPIOs as output. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: enable BOCO2 FPGA download supportValentin Longchamp2012-07-07-0/+3
| | | | | | | | | | | | | | | | | | | | | | | This adds a first support of the FPGA download for a PCIe FPGA based on the BOCO2 CPLD. This takes place in 3 steps, all done accessing the SPICTRL reg of the BOCO2: 1) start the FPGA config with an access to the FPGA_PROG bit 2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1 for the end of the FPGA configuration (with a timeout) 3) reset the FPGA 4) finally remove the access to its config EEPROM from the FPGA so that the CPU can update the FPGA configuration when the kernel is running The boards with a PCIe FPGA but without BOCO2 still are supported. The config option name is CONFIG_KM_FPGA_CONFIG Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: add kmnusa board supportHolger Brunck2012-07-07-9/+35
| | | | | | | | | | | | | | | | This board is similar to portl2, but it has the u-boot environment in a SPI NOR flash and not in an i2c eeprom like portl2 have. Some other details: - IVM EEPROM is at adress: pca9547:70:9 - PCI is enabled - PIGGY4 is connected via MV88E6352 simple switch. There is no phy between the simple switch and the kirkwood. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: use spi claim bus to switch between SPI and NANDValentin Longchamp2012-07-07-3/+6
| | | | | | | | | | | | | | We overwrite these weak functions from the kirkwood spi code to use our own method to be able to switch between the SPI NOR and the NAND flash. This is needed e.g. to update the u-boot. The former command do_spi_toggle can therefore be removed. And the usage of this command is removed from the u-boot update command in the u-boot environment. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* km_arm: use filesize for erase in update commandValentin Longchamp2012-07-07-1/+1
| | | | | | | | | | | | | We used to have an arbitrary value, which can be a problem if we have a u-boot image that is bigger than this value. This patch is dependant on the whole km/arm series and will be included in the v3 of the series if there is one. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: enable mii cmdValentin Longchamp2012-07-07-0/+1
| | | | | | | | | This is useful to debug the switch initialization Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: remove CONFIG_RESET_PHY_RHolger Brunck2012-07-07-1/+0
| | | | | | | | | This is already defined in the generic kirkwood header. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATEHolger Brunck2012-07-07-2/+2
| | | | | | | | | | | | This config option sounds like the it is responsible for the update of the environment, but it is the u-boot update handling. Therefore we adapt it to a more apropriate naming. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-20-1/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* km/common: check test_bank and testpin for testbootThomas Herzmann2012-06-15-1/+3
| | | | | | | | | | If the testpin is asserted, first check if a test_bank variable is defined before trying to boot this test_bank. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: increase bootlimit to 3Holger Brunck2012-06-15-1/+1
| | | | | | | | Increase bootlimit to 3 to be more tolerant during the boot process before switching to the backup application. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx: add kmcoge5ne board supportHolger Brunck2012-06-15-0/+2
| | | | | | | | | | | | | | | | | | This board is a MPC8360 board. Two flashes are present a NOR flash were u-boot and the u-boot environment is stored and a NAND flash for the application code. This board has 512MB SDRAM. Additionaly we introduce a common km8360.h file and convert kmeter1 to use this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Christian Herzig <christian.herzig@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: add support for second flashAndreas Huber2012-06-15-19/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for a second flash. By default, a single flash chip is set up: - called 'boot' - mtd name for ubi 'ubi0' MTDIDS and MTDPARTS may be overwritten to add a second flash. The 'ubiattach' command is featured in two versions: - if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined: this is the version as up to now - if CONFIG_KM_UBI_PARTITION_NAME_APP is defined: a check on 'actual_bank' will be done to determine the flash to boot from. Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader and the applications. Example: In the board config do: ... snip ... "boot:" \ "768k(u-boot)," \ "128k(env)," \ "128k(envred)," \ "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" \ "app:" \ "-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");" ... snap ... You may also need to enable the second flash: ... snip ... /* additional featured for COGE5 */ ... snap ... Signed-off-by: Andreas Huber <andreas.huber@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* arm/km: speed up i2c access for keymile boardsHolger Brunck2012-02-12-1/+1
| | | | | | | | | | | | We don't need 3us delay for our i2c bus. Decrease it to 1us. It would also be possible to use 100ns in the future, but currently kirkwood has no ndelay implementation. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* NAND: remove NAND_MAX_CHIPS definitionsVladimir Zapolskiy2012-01-26-1/+0
| | | | | | | | | | | This change follows the change by Wolfgang Grandegger (commit 6c869637fef), which allows to remove useless NAND_MAX_CHIPS definitions in board config files. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* powerpc/83xx/km: update SDRAM parameters for km8321 boardsMarco Schmid2012-01-09-10/+14
| | | | | | | | | | | Measurements during HW basic test showed, that the SDRAM timing has to be optimized. This patch adapted these timings accordingly. Signed-off-by: Marco Schmid <marco.schmid@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2011-11-08-13/+15
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mpc83xx: powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code mpc83xx: Cleanup usage of LBC constants mpc83xx: Cleanup usage of DDR constants mpc83xx: Cleanup usage of BAT constants mpc83xx: cosmetic: vme8349.h checkpatch compliance mpc83xx: cosmetic: ve8313.h checkpatch compliance mpc83xx: cosmetic: sbc8349.h checkpatch compliance mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance mpc83xx: cosmetic: kmeter1.h checkpatch compliance mpc83xx: cosmetic: TQM834x.h checkpatch compliance mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance mpc83xx: cosmetic: MVBLM7.h checkpatch compliance mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance mpc83xx: Fix ipic structure definition powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions cosmetic, powerpc, mpc83xx: checkpatch cleanup powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c mpc83xx: fix global timer structure definition
| * mpc83xx: Cleanup usage of LBC constantsJoe Hershberger2011-11-03-6/+8
| | | | | | | | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * mpc83xx: Cleanup usage of BAT constantsJoe Hershberger2011-11-03-7/+7
| | | | | | | | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | arm/km: enable jffs2 cmdsHolger Brunck2011-11-03-1/+0
| | | | | | | | | | | | Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* | arm/km: add boardid and hwkey to kernel command lineHolger Brunck2011-11-03-1/+2
| | | | | | | | | | | | | | | | | | | | We need in some cases a possibility for the kernel to distinguish on which board he is running. On powerpc we did this with different dts files. On arm currently we can't do this, so add boardid and hwkey to the kernel command line and use it later on in the kernel code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* | ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boardsValentin Longchamp2011-11-03-0/+5
|/ | | | | | | | | | | | | | We got dropped from Linux mach-types.h because of a lack of mainline support and this is needed since the last Linux/u-boot mach-types synchro. This patch also defines CONFIG_MACH_TYPE for all keymile boards, as this is a mandatory CONFIG for ARM boards now. The initialization of gd->bd->bi_arch_number is removed form km_arm.c, our board file. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* Revert "km_arm: enable POST for these boards"Wolfgang Denk2011-10-24-6/+0
| | | | | | | | | This reverts commit a2da616311151ecfab8b8fcc510686fc3c0c9a21. THis was applied by accident - a more recent version of this change was already present, see commit 9400f8f 2011-10-05 22:03:11 +0200 km_arm: enable POST for these boards Signed-off-by: Wolfgang Denk <wd@denx.de>
* km/common: enable "env default" for all keymile boardsGerlando Falauto2011-10-22-0/+1
| | | | | Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common: fix ramfs development targetAndreas Huber2011-10-22-1/+1
| | | | | | | | | | Calucations of PRAM needs to take into account the 'rootfssize'. Memory available to the linux kernel 'mem=' is in all cases set to the total memory size minus the pram size. Signed-off-by: Andreas Huber <andreas.huber@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Wolfgang Denk <wd@denx.de>
* km_arm: enable POST for these boardsValentin Longchamp2011-10-22-0/+6
| | | | | | | | | | | | The current km_arm boards have a Power-On test jumper. When this jumper is set, this triggers some Power-On tests on the board. This patch enables the support of this jumper for starting the memory_regions test when the jumper is set. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com>
* board configs: drop NET_MULTI referencesMike Frysinger2011-10-05-5/+0
| | | | | | | Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* km_arm: enable POST for these boardsValentin Longchamp2011-10-05-0/+6
| | | | | | | | | | | | The current km_arm boards have a Power-On test jumper. When this jumper is set, this triggers some Power-On tests on the board. This patch enables the support of this jumper for starting the memory_regions test when the jumper is set. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com>
* km_arm: change CONFIG_SYS_TEXT_BASE to end of RAMValentin Longchamp2011-10-05-1/+1
| | | | | | | | | This allows to test a larger part of the RAM in the memory tests. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Cc: Heiko Schocher <hs@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com>
* Drop bogus BOOTFLAG_* definitionsWolfgang Denk2011-09-20-5/+0
| | | | | | | | | | There is no code anywhere that references BOOTFLAG_* so remove these defines. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Peter Tyser <ptyser@xes-inc.com>
* km/common: moved eeprom config to pbec specific partStefan Bigler2011-07-28-6/+12
| | | | | | | | | | | Moved eeprom config to specific part, to allow bigger eeprom write pages for km_kirkwood designs. Write page only used for env eeprom in std use cases. 24C128 has page size of 64bytes -> 8 time faster. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: use u-boot.kwb for u-boot update function on armHolger Brunck2011-07-28-1/+2
| | | | | | | | | | | | Now we use the standard u-boot make to build the Kirkwood binary. The output file is u-boot.kwb. So use this name for the tftp update function to avoid confusion, because this is the binary we need on Kirkwood. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: enable cramfs and cramfs cmdlineHolger Brunck2011-07-27-1/+3
| | | | | | | | | | | All the km boards uses CRAMFS images where the kernel is stored. This isn't architecture specific because we use it on ARM and POWERPC. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* powerpc/km82xx: remove 82xx specific functions from common.cHolger Brunck2011-07-27-0/+7
| | | | | | | | | | Common code should be valid for more than one architecture, therefore the km82xx specific code was removed from common.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: remove obsolete defines and headerHolger Brunck2011-07-27-10/+0
| | | | | | | | | | These defines and the header keymile_hdlc_enet.h are obsolete due to the removed hdlc code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: simplify debug environmentHolger Brunck2011-07-27-15/+13
| | | | | | | | | | | | | | | | | | | The debug environment which is stored in textfiles in the scripts directory was reworked. Two usecase are now present which can be executed simply from the default environment: run develop: this configures the environment to setup the rootfs via nfs run ramfs: this configures the environment to setup the rootfs in ram Each architecture now has a "arch" variable which is used to load the architecture specific debug scripts and to set the rootpath for NFS. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* km/common: add test sw starting variableThomas Herzmann2011-07-27-0/+2
| | | | | | | | | | The test SW is started when the test_bank variable is set. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* km/common: rework and simplify default environmentHolger Brunck2011-07-27-94/+35
| | | | | | | | | | | | | | | This is the second step to simplify and decrease the default environment for the keymile boards. The release usecase formaly used to set the production environment was removed and the default configuration is now the production environment. So the formar environment variable "release" which has done a lot of things in the past, simply erase the current environment and do a reset which forces u-boot to setup the default environment again. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de>
* arm/km: use board KM_ENV_BUS for CONFIG_I2C_ENV_EEPROM_BUSValentin Longchamp2011-07-04-1/+1
| | | | | | | | | | | This is defined for all km_kirkwood boards and was not used up to now. This value was the same for all boards but it could be changed for some boards (and thus needs to be defined for every board). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Heiko Schocher <hs@denx.de>
* arm/km: remove unneeded defineHolger Brunck2011-07-04-2/+0
| | | | | | | | | | | CONFIG_ENV_SIZE for NAND was later in this file overwritten because we have the environment in i2c eeprom, so remove this define. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Heiko Schocher <hs@denx.de>
* arm/km: fix u-boot.kwb build breakageHolger Brunck2011-07-04-22/+6
| | | | | | | | | | | | | | | | | | | commit 010a958b (arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h) breaks building keymile arm targets, when u-boot.kwb tries to generate the binary with mkimage. A simple make <board> or MAKEALL succeeded because it don't try to build the kirwood binary at the end. Due this commit we use the CONFIG_SYS_KWD_CONFIG from the arch-kirkwood/config.h and it was removed from the board config. But it was forgotten to include the header. Now the header is included in km_arm.h. Some other defines were obsolete due to this include, these are also removed in this commit. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Heiko Schocher <hs@denx.de>
* arm/km: add second serial interface for kirkwoodHolger Brunck2011-05-31-0/+6
| | | | | | | | | Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: disable ls (through jffs2 support)Valentin Longchamp2011-05-31-0/+1
| | | | | | | | | | | | | | | This is not supported on our km-arm boards since we have defined CONFIG_SYS_NO_FLASH for our NAND Flash chip. With CONFIG_CMD_JFFS2, the ls command is present and works very badly on our km-arm boards. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* arm/km: introduce bootcount env variable and clean km_armValentin Longchamp2011-05-31-0/+3
| | | | | | | | | | | | | | | | | | This environment variable is used to set the bootcount address for the kernel. last_stage_init is not available for arm platforms. So the calls to set_km_var and set_bootcount_addr are done in misc_init_r. Additionally some unneeded printouts were removed. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: move CONFIG_EXTRA_ENV_SETTINGS from board to km_arm fileValentin Longchamp2011-05-31-0/+15
| | | | | | | | | | | | Since all the boards define the same env settings, this simplifies the board files. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.hValentin Longchamp2011-05-31-9/+0
| | | | | | | | | | | | | This define is marvell specific, so it should be present in km_arm. It is however not needed there either, since we set it to the default value that is already set in include/asm/arch-kirkwood/config.h Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: add pnvramsize to default environmentHolger Brunck2011-05-18-0/+1
| | | | | | | | | | | The pnvram size was used later from start scripts in linux. Therefore it was added to the default environment. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: simplify default environmentHolger Brunck2011-05-18-126/+19
| | | | | | | | | | | | | | This is a first step to simplify the default environment. Move all the environment variables which are only needed for debugging purpose to textfiles in the scripts directory. In case of debugging these files can be loaded via tftp into RAM and set via the env import command. Other variables are identified as obsolete and were removed. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* km/common: implement boardId HWkey checks as u-boot cmdThomas Herzmann2011-05-18-29/+1
| | | | | | | | | | | | | | | | | | | | | | | | BoardId and HWKey are used to identify the HW class of a given board. The correct values are stored in the inventory eeprom. During creation time of a boot package the boardId and HWkey for the SW is stored in the default environment and burned into the flash. During boottime the values in the inventory and in the environment are compared to avoid starting of a SW which is not authorized for this board. Some bootpackages are allowed to run on a set of different boardId hwKey. In this case the environment variable boardIdListHex was added to the default environment. In this case the command iterates over the pair values and compares them with the values read from the inventory eeprom. The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2 Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Heiko Schocher <hs@denx.de> cc: Wolfgang Denk <wd@denx.de> cc: Detlev Zundel <dzu@denx.de>
* Remove remnants of obsolete CONFIG_SYS_GBL_DATA_SIZE commentsMichael Jones2011-05-12-2/+0
| | | | | | | commit 25ddd1fb0a2281b182529afbc8fda5de2dc16d96 left remnants of many comments about CONFIG_SYS_GBL_DATA_SIZE. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
generated by cgit v1.1 at 2024-11-05 23:57:21 +0000