arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	davinci: add support for printing clock frequency	Hadli, Manjunath	2012-02-12	-0/+4
\| \| \| \| \| \| \| \| \|	add support for printing various clock frequency info found in SOC such as ARM core frequency, DSP core frequency and DDR frequency as part of bdinfo command. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: Tom Rini <trini@ti.com>
*	NAND: remove NAND_MAX_CHIPS definitions	Vladimir Zapolskiy	2012-01-26	-1/+0
\| \| \| \| \| \| \| \| \| \| \|	This change follows the change by Wolfgang Grandegger (commit 6c869637fef), which allows to remove useless NAND_MAX_CHIPS definitions in board config files. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
*	Davinci: ea20: added PREBOOT to configuration	Stefano Babic	2011-11-03	-0/+1
\| \| \| \| \| \| \| \| \|	PREBOOT is used on the ea20 to load a splash image at the start up. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Davinci: ea20: added I2C support	Stefano Babic	2011-11-03	-0/+8
\| \| \| \| \| \|	Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Davinci: ea20: added video support	Stefano Babic	2011-11-03	-1/+13
\| \| \| \| \| \| \| \|	Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Anatolij Gustschin <agust@denx.de> CC: Sandeep Paulraj <s-paulraj@ti.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Davinci: ea20: add gpio for keeping power on in board_late_init	Bastian Ruppert	2011-11-03	-0/+1
\| \| \| \| \| \| \| \| \| \| \|	The pin called HALTEN drives a transistor to operate the supply voltage. After HALTEN is high, the user can release the power switch button and the device will stay powered on. Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de> CC: sbabic@denx.de CC: dzu@denx.de Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Davinci: ea20: Add default U-Boot environment	Stefano Babic	2011-11-03	-0/+80
\| \| \| \| \| \| \|	Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de> CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Davinci: ea20: Add NAND support	Stefano Babic	2011-11-03	-3/+17
\| \| \| \| \| \| \|	Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	Davinci: ea20: set console on UART0	Bastian Ruppert	2011-11-03	-1/+1
\| \| \| \| \| \| \|	Signed-off-by: Bastian Ruppert <Bastian.Ruppert@Sewerin.de> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM	Manjunath Hadli	2011-10-27	-1/+0
\| \| \| \| \| \| \| \| \|	remove macro CONFIG_EMAC_MDIO_PHY_NUM and depending macro EMAC_MDIO_PHY_NUM as they are no longer needed with the support for more than 1 PHYs in davinci emac driver. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
*	board configs: drop NET_MULTI references	Mike Frysinger	2011-10-05	-1/+0
\| \| \| \| \| \| \|	Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
*	Davinci: add support for the ea20 board	Stefano Babic	2010-11-30	-0/+192
	This board uses the OMAP-L138 SOM stacked on a custom baseboard. It supports SPI Flash, Ethernet with RMII. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>