summaryrefslogtreecommitdiff
path: root/include/configs/da850evm.h
Commit message (Collapse)AuthorAgeLines
...
* da850: add NOR boot mode supportNagabhushana Netagunte2011-09-04-0/+17
| | | | | | | | | Add pin-mux support for NOR in board file and correspanding macros to use NOR boot mode in configuration file. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da850: indicate cache usage disable in config fileNagabhushana Netagunte2011-09-04-0/+3
| | | | | | | | | | | | | | | there are cache coherency issues when using the DAVINCI Ethernet driver, hence caches cant be used for da850 u-boot. As per new cache management framework,if the caches are not used in u-boot, it needs to be explicitly indicated through macros in config file. CACHE disable is indicated by the following macro definitions in config file, 1. CONFIG_SYS_ICACHE_OFF 2. CONFIG_SYS_DCACHE_OFF 3. CONFIG_SYS_L2CACHE_OFF Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da850: Add RMII support for EMACSudhakar Rajashekhara2010-11-30-0/+1
| | | | | | | | | | | | | | | | | | | | | | | This patch is a port of the work by Sudhakar Rajeshekhara in commit ab3effbcad8851cc65dc5241a01c064d2030a3b2 of git://arago-project.org/git/people/sandeep/u-boot-davinci.git. The da850 UI board has on it an RMII PHY which can be used if the MDC line to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by configuring the values of some GPIO pins on the IO expander of the UI board. This patch implements disabling that line via GPIO2[6], configuring the UI board's IO expander and setting only the pinmux settings that are needed for RMII operation. Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Mike Frysinger <vapier@gentoo.org> CC: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da850: Enable SPI FlashStefano Babic2010-11-28-0/+28
| | | | | | | | | | | | The patch was already posted to the arago project, but not yet to mainline. It allows to save environment into the spi flash. Tested on LogiPD tmdxl138. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Detlev Zundev <dzu@denx.de> CC: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* DaVinci: remove bogus DEF_BOOTM definitionWolfgang Denk2010-11-19-1/+0
| | | | | | | | | Some boar config files defined DEF_BOOTM but this was not used anywhere in the code. Remove this bogus define. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* DA850 EVM: passing maximum clock rate information to kernelSekhar Nori2010-11-19-0/+1
| | | | | | | | | | | | | | | | | | | | The TI DA850/OMAP-L138/AM18x EVM can be populated with devices having different maximum allowed CPU clock rating. The maximum clock the chip can support can only be determined from the label on the package (not software readable). Introduce a method to pass the maximum allowed clock rate information to kernel using ATAG_REVISION. The kernel uses this information to determine the maximum cpu clock rate reachable using cpufreq. Note that U-Boot itself does not set the CPU clock rate. The CPU clock is setup by a primary bootloader ("UBL"). The rate setup by UBL could be different from the maximum clock rate supported by the device. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Remove config.mk for da8xxevm based boards.Sughosh Ganu2010-10-26-0/+1
| | | | | | | | Move CONFIG_SYS_TEXT_BASE to the board's config file, and remove the now unnecessary config.mk file. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
* Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated valueWolfgang Denk2010-10-26-2/+1
| | | | | | | | | | | | | | | | | | CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org>
* da850evm: fix linux bootparam addressBen Gardiner2010-10-17-1/+1
| | | | | | | | | | | | | This patch fixes the LINUX_BOOT_PARAM_ADDR define to be based off of PHYS_SDRAM_1 instead of CONFIG_SYS_MEMTEST_START. On da830 they are the same thing but on da850 the CONFIG_SYS_MEMSTART define is offset from the PHYS_SDRAM_1 start. Without this patch it is not possible to boot linux on da850 -- bootm hangs at "Uncompressing Linux... done, booting the kernel." Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da850evm: basic MII EMAC supportBen Gardiner2010-10-17-0/+15
| | | | | | | | | | | | | | | | The current da850evm support in u-boot/master omits any use of the davinci EMAC. This patch adds basic support for the EMAC using the MII PHY found on the baseboard of the EVM. The MAC address is read from the environment variable 'ethadd'. Note that this is different from the da850evm support in the u-boot omapl1 tree where the MAC address is read from SPI flash. Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Sandeep Paulraj <s-paulraj@ti.com> CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da850evm: add mtdpart and ubi commands with NAND supportBen Gardiner2010-10-17-0/+8
| | | | | | | | | This patch enables also the mtdpart, ubi and ubifs commands when NAND support is enabled. Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca> To: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* da850evm: setup NAND support under CONFIG_USE_NANDBen Gardiner2010-10-17-0/+29
| | | | | | | | | | | | | | The current da850evm config is missing the pieces for NAND support that can be found in Sandeep's u-boot-davinci tree [1]. This patch adds NAND support in the spirit of the support in the u-boot-davinci tree where NAND support for the da850evm can be enabled by putting a single '#define CONFIG_USE_NAND' at the top of the include/configs/da850evm.h file. [1] http://arago-project.org/git/people/?p=sandeep/u-boot-davinci.git;a=tree Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARM: relocation: don't undef CONFIG_SYS_ARM_WITHOUT_RELOCBen Gardiner2010-10-13-1/+0
| | | | | | | | | There were some #undef's of CONFIG_SYS_ARM_WITHOUT_RELOC added to a few board configs as part of the arm relocation series; but these are not needed now as we do not #undef what is not #defined in the first place. Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> CC: Heiko Schocher <hs@denx.de>
* da8xx: fixup ARM relocation supportBen Gardiner2010-09-19-0/+1
| | | | | | | | | | | | | | | | | | | | | Split the existing dram_init for da8xx when ARM reloc is enabled, like the changes to arch/arm/cpu/arm926ejs/orion5x/dram.c in 0f234d263b17ccf1b8fd776eb8c15b7cdb27a887 by Heiko Schocher <hs@denx.de>. Without these changes gd->ram_size is '0' which leads to incorrect relocation when CONFIG_SYS_ARM_WITHOUT_RELOC is defined and the board does not boot. We use get_ram_size to dynamically calculate the available RAM because it runs on different board version with different ram, as suggested by Heiko in private communication. Tested on a da850evm with 128M of DDR2 installed; with both CONFIG_SYS_ARM_WITHOUT_RELOC defined and undefined. Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> CC: Sudhakar Rajashekhara <sudhakar.raj@ti.com> CC: Heiko Schocher <hs@denx.de>
* ARM: implement relocation for ARM926Heiko Schocher2010-09-19-1/+5
| | | | | | | | | | | | | | | | | | | | | Change the implementation for arm926 to relocate the code to an arbitrary address in RAM. Adapt the TX25 (i.MX25), magnesium board to test the changes. On the tx25 board TEXT_BASE is set to the final relocation address to prevent one more copying of u-boot code when relocating. More info see: doc/README.arm-relocation da850 board: Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca>
* TI: DaVinci: Add board specific code for da850 EVMSudhakar Rajashekhara2010-06-10-0/+140
Provides initial support for TI OMAP-L138/DA850 SoC devices on a Logic PD EVM board. Provides: Initial boot and configuration. Support for i2c. UART support (console). Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Acked-by: Ben Gardiner <bengardiner@nanometrics.ca> Reviewed-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit v1.1 at 2024-11-05 07:57:02 +0000