arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	compulab: eeprom: add support for defining eeprom i2c bus	Nikita Kiryanov	2014-09-09	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM module what I2C bus the EEPROM is located at. Make cl_eeprom_read() switch to that bus when reading EEPROM. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
*	ARM: omap: move board specific NAND configs out from ti_armv7_common.h	pekon gupta	2014-07-25	-0/+5
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	This patch moves some board specific NAND configs: - FROM: generic config file 'ti_armv7_common.h' - TO: individual board config files using these configs. So that each board can independently set the value as per its design. Following configs are affected in this patch: CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand> CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon> CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon> CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon> This patch also updates documentation for few of above NAND configs. Signed-off-by: Pekon Gupta <pekon@ti.com>
*	omap3: remove remnant macros GPMC_NAND_ECC_LP_x8_LAYOUT and ↵	pekon gupta	2014-06-06	-1/+0
\| \| \| \| \| \| \| \| \| \| \|	GPMC_NAND_ECC_LP_x16_LAYOUT OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros to configure GPMC controller for x7 or x8 bit device connected to its interface. Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above macros can be completely removed. Signed-off-by: Pekon Gupta <pekon@ti.com>
*	drivers: net: cpsw: add support to have phy address from cpsw platform data	Mugunthan V N	2014-03-04	-1/+0
\| \| \| \| \| \| \| \| \| \| \| \|	Some platforms like AM437x have different EVMs with different phy addresses, so this patch adds support for passing phy address via cpsw plaform data. Also renamed phy_id to phy_addr so better understanding of the code. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> [trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335 pengwyn boards] Signed-off-by: Tom Rini <trini@ti.com>
*	cm_t335: add support for pca9555 i2c gpio extender	Ilya Ledvich	2013-12-04	-0/+12
\| \| \| \| \| \| \| \|	Add support for the 16 bits pca9555 i2c to gpio extender featured by the SB-T335 baseboard. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
*	cm_t335: add support for status LED	Ilya Ledvich	2013-12-04	-0/+10
\| \| \| \| \| \| \| \|	Add support for status LED. Use the STATUS_LED APIs for indicating a boot progress. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
*	cm_t335: add cm_t335 board support	Ilya Ledvich	2013-12-04	-0/+160
	Add cm_t335 board directory, config file. Enable build. Signed-off-by: Ilya Ledvich <ilya@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> [trini: Adapt Makefile] Signed-off-by: Tom Rini <trini@ti.com>