| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
This option specifies the default Device Tree used for the run-time
configuration of U-Boot.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <michal.simek@xilinx.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit moves:
CONFIG_OF_CONTROL
CONFIG_OF_SEPARATE
CONFIG_OF_EMBED
CONFIG_OF_HOSTFILE
Because these options are currently not supported for SPL,
the "Device Tree Control" menu does not appear in the SPL
configuration.
Note:
zynq-common.h should be adjusted so as not to change the
default value of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enable DFU protocol support (via the "dfu" command) on Tegra boards where
USB device/gadget mode is enabled.
Note that for DFU to operate correctly on Tegra, we still need some DFU
fixes/enhancements that are going through the DFU -> USB trees. However,
the code builds just fine without those changes, and applying this patch
now will allow both sets of patches to meet in the main U-Boot tree much
more quickly.
In order to run test/dfu/dfu_gadget_test.sh, you would need to add the
following to the board configuration:
CONFIG_EXT4_WRITE
CONFIG_CMD_EXT4_WRITE
However, I haven't enabled those here, since I believe the main use-case
for DFU on Tegra is raw flash writing, rather than filesystem access, so
we don't need the additional code-size hit. However, I could be persuaded
otherwise! We should probably add a separate test script for raw flash
access.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For each of Jetson TK1, Venice2, and Beaver:
- Enable the first USB controller in DT, and describe its configuration.
- Enable USB device/gadget support. This allows the user to type e.g.
"ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
implementing the USB Mass Storage protocol, and expose MMC device 0
that way.
This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
U-Boot on Tegra30 currently selects a main CPU frequency that cannot be
supported at all on some SKUs, and needs higher VDD_CPU/VDD_CORE values
on some others. This can result in unreliable operation of the main CPUs.
Resolve this by switching to a CPU frequency that can be supported by any
SKU. According to the following link, the maximum supported CPU frequency
of the slowest Tegra30 SKU is 600MHz:
repo http://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=summary
branch l4t/l4t-r16-r2
path arch/arm/mach-tegra/tegra3_dvfs.c
table cpu_dvfs_table[]
According to that same table, the minimum VDD_CPU required to operate at
that frequency across all SKUs is 1.007V. Given the adjustment resolution
of the TPS65911 PMIC that's used on all Tegra30-based boards we support,
we'll end up using 1.0125V instead.
At that VDD_CPU, tegra3_get_core_floor_mv() in that same file dictates
that VDD_CORE must be at least 1.2V on all SKUs. According to
tegra_core_speedo_mv() (in tegra3_speedo.c in the same source tree),
that voltage is safe for all SKUs.
An alternative would be to port much of the code from tegra3_dvfs.c and
tegra3_speedo.c in the kernel tree mentioned above. That's more work
than I want to take on right now.
While all the currently supported boards use the same regulator chip for
VDD_CPU, different types of regulators are used for VDD_CORE. Hence, we
add some small conditional code to select how VDD_CORE is programmed. If
this becomes more complex in the future as new boards are added, or we
end up adding code to detect the SoC SKU and dynamically determine the
allowed frequency and required voltages, we should probably make this a
runtime call into a function provided by the board file and/or relevant
PMIC driver.
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Bard Liao <bardliao@realtek.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
|
| |
|
|
|
|
|
|
| |
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add USB EHCI, storage and network support.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
| |/
|
|
|
|
|
|
|
|
|
| |
Use a negative value of CONFIG_ENV_OFFSET for all NVIDIA reference boards
that store the U-Boot environment in the 2nd eMMC boot partition. This
makes U-Boot agnostic to the size of the eMMC boot partition, which can
vary depending on which eMMC device was actually stuffed into the board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
|
Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu.
Add a Beaver build so it can begin to be differentiated, if need be.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
