arm-boot/u-boot-imx.git - U-boot NXP imx6

	Commit message (Collapse)	Author	Age	Lines
*	8xxx: Removed CONFIG_NUM_CPUS from 85xx/86xx	Poonam Aggrwal	2009-08-28	-1/+0
\| \| \| \| \| \| \| \| \| \| \| \| \|	The number of CPUs are getting detected dynamically by checking the processor SVR value. Also removed CONFIG_NUM_CPUS references from all the platforms with 85xx/86xx processors. This can help to use the same u-boot image across the platforms. Also revamped and corrected few Freescale Copyright messages. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
*	xpedite5370: Enable NAND command support	Peter Tyser	2009-07-22	-1/+8
\| \| \| \| \| \| \| \| \| \| \|	Use the MPC8572's eLBC to access 1 GB (or greater) onboard NAND flash via the 'nand' command. Previously, the XPedite5370's NAND chip selects were properly configured, but NAND support was not enabled. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
*	xes: Increase CONFIG_SYS_BOOTM_LEN to 16MB	Peter Tyser	2009-07-22	-0/+1
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to support uncompressing images larger than 8 MB when using the bootm command. Note that recent Linux kernels for the 85xx and 86xx map greater than 16MB of memory on bootup, but we use 16MB to maintain compatibility with older Linux kernels for now. Signed-off-by: Nate Case <ncase@xes-inc.com> Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
*	xpedite5200,5370: Use buffered NOR flash writes	Peter Tyser	2009-07-22	-0/+1
\| \| \| \| \| \| \| \|	Buffered writes are possible on the XPedite5200 and XPedite5370 and greatly improve NOR flash write speeds Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
*	i2c: Remove deprecated individual i2c commands	Peter Tyser	2009-06-12	-1/+0
\| \| \| \| \| \| \| \| \| \| \| \| \|	The following individual I2C commands have been removed: imd, imm, inm, imw, icrc32, iprobe, iloop, isdram. The functionality of the individual commands is still available via the 'i2c' command. This change only has an impact on those boards which did not have CONFIG_I2C_CMD_TREE defined. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
*	rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV	Mike Frysinger	2009-02-18	-1/+1
\| \| \| \| \| \| \| \|	The CONFIG_CMD_ENV option controls enablement of the `saveenv` command rather than a generic "env" command, or anything else related to the environment. So, let's make sure the define is named accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
*	XPedite5370 board support	Peter Tyser	2008-12-19	-0/+589
	Initial support for Extreme Engineering Solutions XPedite5370 - a MPC8572-based 3U VPX single board computer with a PMC/XMC site. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>