summaryrefslogtreecommitdiff
path: root/include/configs/T208xQDS.h
Commit message (Collapse)AuthorAgeLines
* mpc85xx: configs - Enable blob command in freescale platformsRuchika Gupta2014-10-16-0/+1
| | | | | | | | Enable blob commands for platforms having SEC 4.0 or greater for secure boot scenarios Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: configs - Add hash command in freescale platformsRuchika Gupta2014-10-16-0/+7
| | | | | | | | | Enable CAAM in platforms supporting the hardware block. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* include: remove CONFIG_SPL/CONFIG_TPL definition in config headersMasahiro Yamada2014-07-30-1/+0
| | | | | | | | | Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig. Remove the redundant definition in config headers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* include: define CONFIG_SPL and CONFIG_TPL as 1Masahiro Yamada2014-07-30-1/+1
| | | | | | | | | | | | | | | | We are about to switch to Kconfig in the next commit. But there are something to get done beforehand. In Kconfig, include/generated/autoconf.h defines boolean CONFIG macros as 1. CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1. Otherwise, when switching to Kconfig, the build log would be sprinkled with warning messages like this: warning: "CONFIG_SPL" redefined [enabled by default] Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* board/freescale: use generic board architecture for t2080qds and t2080rdbShengzhou Liu2014-07-23-0/+2
| | | | | | Tested with NOR boot and NAND boot on T2080QDS and T2080RDB. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
* board/t2080qds: enable sst and eon spi flash for nor bootShengzhou Liu2014-07-22-1/+1
| | | | | | | | Remove unnecessary condition CONFIG_RAMBOOT_PBL to have SST and EON SPI flash work in case of NOR boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t2080qds: some update for ddrShengzhou Liu2014-06-05-2/+3
| | | | | | | | | | - add support for 2nd DIMM slot. - make it work with DIMM which is less than 2GB. Verified with two 2GB UDIMM MT9JSF25672AZ-2G1K1 in two DIMM slots. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/srio-pcie-boot: Adjust addresses for SRIO/PCIE bootLiu Gang2014-05-16-5/+5
| | | | | | | | | | | | | | | | | The new 768KB u-boot image size requires changes for SRIO/PCIE boot. These addresses need to be updated to appropriate locations. The updated addresses are used to configure the SRIO/PCIE inbound windows for the boot, and they must be aligned with the window size based on the SRIO/PCIE modules requirement. So for the 768KB u-boot image, the inbound window cannot be set with 0xfff40000 base address and 0xc0000 size, it should be extended to 1MB size and the base address can be aligned with the size. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: configs: remove c=ffe from default environmentKim Phillips2014-05-16-2/+1
| | | | | | | | | | | AFAICT, c=ffe does nothing and was a typo from the original commit d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support for the P4080DS board" and just kept on getting duplicated in subsequently added board config files. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Edward Swarthout <ed.swarthout@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t208xqds: Add support of 2-stage NAND/SPI/SD bootShengzhou Liu2014-04-22-20/+93
| | | | | | | | | | | | Add support of 2-stage NAND/SPI/SD boot loader using SPL framework. PBL initializes the internal CPC-SRAM and copy SPL(160K) to it, SPL further initializes DDR using SPD and environment and copy u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers control to u-boot. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH] Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx:Update MONITOR_LEN for 768KB u-boot sizePrabhakar Kushwaha2014-04-22-1/+1
| | | | | | | | | U-boot binary size has been increased from 512KB to 768KB. So update CONFIG_SYS_MONITOR_LEN to reflect the same. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/T208xQDS: add mtdparts suppportShengzhou Liu2014-04-22-0/+17
| | | | | | | | We use dynamical mtdparts partition instead of directly puting mtd partitions nodes in device tree. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t208xqds: fix nor chip selection when nand bootShengzhou Liu2014-04-22-10/+18
| | | | | | | | NOR flash is on CS1 instead of CS2 when NAND boot. So correct NOR chip selection to CS1 from CS2. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and ↵Zhao Qiang2014-04-22-5/+5
| | | | | | | | | | | CONFIG_SYS_QE_FW_ADDR CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address. Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address, and CONFIG_SYS_QE_FW_ADDR for QE microcode address. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* freescale: pblimage: refactor CONFIG_SYS_FSL_PBL_{PBI, RCW}Masahiro Yamada2014-03-12-3/+3
| | | | | | | | | | Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: York Sun <yorksun@freescale.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* powerpc/t208xqds: fixup for t208xqdsShengzhou Liu2014-03-07-1/+1
| | | | | | | | Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0. Fix EMI2 for t2080qds, which was caused by adding t2081qds. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-02-25-1/+0
| | | | | | | With this, fixup a trivial build error of get_effective_memsize needing to be updated in the new board/freescale/p1010rdb/spl.c Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/t2081qds: Add T2081 QDS board supportShengzhou Liu2014-02-24-0/+817
T2081 QDS is a high-performance computing evaluation, development and test platform supporting the T2081 QorIQ Power Architecture processor. T2081QDS board Overview ----------------------- - T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz - 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC) - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving - Ethernet interfaces: - Two on-board 10M/100M/1G bps RGMII ports - Two 10Gbps XFI with on-board SFP+ cage - 1Gbps/2.5Gbps SGMII Riser card - 10Gbps XAUI Riser card - Accelerator: - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC - SerDes: - 8 lanes up to 10.3125GHz - Supports SGMII, HiGig, XFI, XAUI and Aurora debug, - IFC: - 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - eSPI: - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040) - USB: - Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - PCIe: - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV) - eSDHC: - Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and voltage translators - I2C: - Four I2C controllers. - UART: - Dual 4-pins UART serial ports Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
generated by cgit v1.1 at 2024-11-02 12:23:30 +0000