summaryrefslogtreecommitdiff
path: root/include/configs/P2041RDB.h
Commit message (Collapse)AuthorAgeLines
* mpc85xx: configs - Enable blob command in freescale platformsRuchika Gupta2014-10-16-0/+4
| | | | | | | | Enable blob commands for platforms having SEC 4.0 or greater for secure boot scenarios Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: configs - Add hash command in freescale platformsRuchika Gupta2014-10-16-0/+7
| | | | | | | | | Enable CAAM in platforms supporting the hardware block. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/srio-pcie-boot: Adjust addresses for SRIO/PCIE bootLiu Gang2014-05-16-5/+5
| | | | | | | | | | | | | | | | | The new 768KB u-boot image size requires changes for SRIO/PCIE boot. These addresses need to be updated to appropriate locations. The updated addresses are used to configure the SRIO/PCIE inbound windows for the boot, and they must be aligned with the window size based on the SRIO/PCIE modules requirement. So for the 768KB u-boot image, the inbound window cannot be set with 0xfff40000 base address and 0xc0000 size, it should be extended to 1MB size and the base address can be aligned with the size. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: configs: remove c=ffe from default environmentKim Phillips2014-05-16-2/+1
| | | | | | | | | | | AFAICT, c=ffe does nothing and was a typo from the original commit d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support for the P4080DS board" and just kept on getting duplicated in subsequently added board config files. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Edward Swarthout <ed.swarthout@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx:Update MONITOR_LEN for 768KB u-boot sizePrabhakar Kushwaha2014-04-22-1/+1
| | | | | | | | | U-boot binary size has been increased from 512KB to 768KB. So update CONFIG_SYS_MONITOR_LEN to reflect the same. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* QE/FMAN: modify CONFIG_SYS_QE_FMAN_FW_ADDR to CONFIG_SYS_FMAN_FW_ADDR and ↵Zhao Qiang2014-04-22-5/+5
| | | | | | | | | | | CONFIG_SYS_QE_FW_ADDR CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address. Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address, and CONFIG_SYS_QE_FW_ADDR for QE microcode address. Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* freescale: pblimage: refactor CONFIG_SYS_FSL_PBL_{PBI, RCW}Masahiro Yamada2014-03-12-3/+2
| | | | | | | | | | Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: York Sun <yorksun@freescale.com> Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* powerpc: mpc85xx: move CONFIG_MPC85xx definition to CPU config.mkMasahiro Yamada2014-01-24-1/+0
| | | | | | | Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk because all target boards with mpc85xx cpu define it. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* powerpc/mpc85xx:Increase binary size for P, B & T series boards.Prabhakar Kushwaha2014-01-21-8/+8
| | | | | | | | | | | u-boot binary size for Freescale mpc85xx platforms is 512KB. This has been reached to upper limit for some of the platforms causig linker error. So, Increase the u-boot binary size to 768KB. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
* powerpc:Rename CONFIG_PBLRCW_CONFIG & CONFIG_SYS_FSL_PBL_PBIPrabhakar Kushwaha2014-01-21-2/+3
| | | | | | | | | Rename CONFIG_PBLRCW_CONFIG and CONFIG_PBLRCW_CONFIG. Also add their details in README. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* kgdb: configs: remove obsolete CONFIG_KGDB_SER_INDEXVladimir Zapolskiy2013-12-13-1/+0
| | | | | | | | The last users of CONFIG_KGDB_SER_INDEX were removed more than 3 years ago in commits 550650ddd0 and bf16500f79, either kgdb subsystem should care about this parameter or it should be gone completely. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
* Driver/DDR: Moving Freescale DDR driver to a common driverYork Sun2013-11-25-1/+1
| | | | | | | Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
* config: remove platform CONFIG_SYS_HZ definition part 1/2Rob Herring2013-11-04-1/+0
| | | | | | Remove platform CONFIG_SYS_HZ definition for configs A-Z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* config: Add a default CONFIG_SYS_PROMPTRob Herring2013-11-04-1/+0
| | | | | | | | | | The definitions for CONFIG_SYS_PROMPT are varied with little reason other than to display the board name. Over half the definitions are "==> ", so make this the default. The rest of the boards remain unchanged to avoid breaking any external scripts expecting a certain prompt. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
* powerpc: add CONFIG_SECURE_BOOT condition into fsl_secure_boot.hPo Liu2013-10-16-2/+0
| | | | | | | This patch is for board config file not to add CONFIG_SECURE_BOOT condition for include the asm/fsl_secure_boot.h. Signed-off-by: Po Liu <Po.Liu@freescale.com>
* powerpc/p2041: fix I2C controller's offsetShaohui Xie2013-09-10-2/+2
| | | | | | | | Without this patch, SPD access will fail which leads to DDR init fail. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Tested-by: Chris Packham <judge.packham@gmail.com> Acked-by: York Sun <yorksun@freescale.com>
* powerpc/corenet: Move CONFIG_FSL_CORENET out of board header fileYork Sun2013-08-09-1/+0
| | | | | | | Move CONFIG_FSL_CORENET define to config_mpc85xx.h. It is not board specific feature and belongs to SoC header. Signed-off-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini2013-07-24-8/+8
|\ | | | | | | | | | | | | | | | | | | | | The sandburst-specific i2c drivers have been deleted, conflict was just over the SPDX conversion. Conflicts: board/sandburst/common/ppc440gx_i2c.c board/sandburst/common/ppc440gx_i2c.h Signed-off-by: Tom Rini <trini@ti.com>
| * i2c, fsl_i2c: switch to new multibus/multiadapter supportHeiko Schocher2013-07-23-8/+8
| | | | | | | | | | | | | | | | | | - added to fsl_i2c driver new multibus/multiadpater support - adapted all config files, which uses this driver Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@wwwdotorg.org>
* | Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
|/ | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/boot: Change the macro of Boot from SRIO and PCIE master moduleLiu Gang2013-06-20-0/+1
| | | | | | | | | | | | | | | | | Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable the master module of Boot from SRIO and PCIE on a platform. But this is not a silicon feature, it's just a specific booting mode based on the SRIO and PCIE interfaces. So it's inappropriate to put the macro into the file arch/powerpc/include/asm/config_mpc85xx.h. Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to "CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros in configuration header file of each board which can support the master module of Boot from SRIO and PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* pci: introduce CONFIG_PCI_INDIRECT_BRIDGE optionGabor Juhos2013-06-07-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The pci_indirect.c file is always compiled when CONFIG_PCI is defined although the indirect PCI bridge support is not needed by every board. Introduce a new CONFIG_PCI_INDIRECT_BRIDGE config option and only compile indirect PCI bridge support if this options is enabled. Also add the new option into the configuration files of the boards which needs that. Compile tested for powerpc, x86, arm and nds32. MAKEALL results: powerpc: --------------------- SUMMARY ---------------------------- Boards compiled: 641 Boards with warnings but no errors: 2 ( ELPPC MPC8323ERDB ) ---------------------------------------------------------- Note: the warnings for ELPPC and MPC8323ERDB are present even without the actual patch. x86: --------------------- SUMMARY ---------------------------- Boards compiled: 1 ---------------------------------------------------------- arm: --------------------- SUMMARY ---------------------------- Boards compiled: 311 ---------------------------------------------------------- nds32: --------------------- SUMMARY ---------------------------- Boards compiled: 3 ---------------------------------------------------------- Cc: Tom Rini <trini@ti.com> Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
* powerpc/p2041: set RCW and PBI files for .pbl build or P2041RDBValentin Longchamp2013-01-30-0/+2
| | | | | | | | | | | In order to be able to build a u-boot.pbl image, both the CONFIG_PBLPBI_CONFIG and CONFIG_PBLRCW_CONFIG variables have to be defined. This patch sets these two files for the P2041RDB board. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: move SATA config to board configurationZang Roy-R619112012-11-27-1/+3
| | | | | | | | | | | | | | | | | | | | board configuration file is included before asm/config_mpc85xx.h. however, CONFIG_FSL_SATA_V2 is defined in asm/config_mpc85xx.h. it will never take effective in the board configuration file for this kind of code : #ifdef CONFIG_FSL_SATA_V2 ... #endif To solve this problem, move CONFIG_FSL_SATA_V2 to board configuration header file. This patch reverts Timur's commit:3e0529f742e893653848494ffb9f7cd0d91304bf Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/P2041RDB: Fix Flash address LAW addressYork Sun2012-11-27-4/+10
| | | | | | | | | P2041RDB uses common corenet TLB and LAW. However it doesn't have promjet connector. It is necessary to use the same base address for correct LAW address. An offset is added for NOR flash. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/qoriq: Move FMAN microcode locationYork Sun2012-11-27-1/+1
| | | | | | | | | Move FMAN microcude from 0xEF000000 to 0xEFF40000 to free up the beginning of this virtual bank so that this bank can store RCW or be used together with other banks to store large images. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* COMMON: Use __stringify() instead of MK_STR()Marek Vasut2012-10-15-3/+3
| | | | | | | | | Kill multiple occurances and redeclaration of MK_STR in favor of __stringify(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* powerpc/fsl-corenet: remove dead variant symbolsScott Wood2012-08-23-1/+1
| | | | | | | | | | | These are not supported as individual build targets, but instead are supported by another target. The dead p4040 defines in particular had bitrotted significantly. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Slave module for boot from PCIELiu Gang2012-08-23-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When boot from PCIE, slave's core should be in holdoff after powered on for some specific requirements. Master will release the slave's core at the right time by PCIE interface. Slave's ucode and ENV can be stored in master's memory space, then slave can fetch them through PCIE interface. For the corenet platform, ucode is for Fman. NOTE: Because the slave can not erase, write master's NOR flash by PCIE interface, so it can not modify the ENV parameters stored in master's NOR flash using "saveenv" or other commands. environment and requirement: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image is in master NOR flash. 3. Put the slave's ucode and ENV into it's own memory space. 4. Normally boot from local NOR flash. 5. Configure PCIE system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to one PCIE interface by RCW. 3. RCW should configure the SerDes, PCIE interfaces correctly. 4. Must set all the cores in holdoff by RCW. 5. Must be powered on before master's boot. For the slave module, need to finish these processes: 1. Set the boot location to one PCIE interface by RCW. 2. Set a specific TLB entry for the boot process. 3. Set a LAW entry with the TargetID of one PCIE for the boot. 4. Set a specific TLB entry in order to fetch ucode and ENV from master. 5. Set a LAW entry with the TargetID one of the PCIE ports for ucode and ENV. 6. Slave's u-boot image should be generated specifically by make xxxx_SRIO_PCIE_BOOT_config. This will set SYS_TEXT_BASE=0xFFF80000 and other configurations. In addition, the processes are very similar between boot from SRIO and boot from PCIE. Some configurations like the address spaces can be set to the same. So the module of boot from PCIE was added based on the existing module of boot from SRIO, and the following changes were needed: 1. Updated the README.srio-boot-corenet to add descriptions about boot from PCIE, and change the name to README.srio-pcie-boot-corenet. 2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to "xxxx_SRIO_PCIE_BOOT", and the image builded with "xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and from PCIE. 3. Updated other macros and documents if needed to add information about boot from PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Master module for boot from PCIELiu Gang2012-08-23-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For the powerpc processors with PCIE interface, boot location can be configured from one PCIE interface by RCW. The processor booting from PCIE can do without flash for u-boot image. The image can be fetched from another processor's memory space by PCIE link connected between them. The processor booting from PCIE is slave, the processor booting from normal flash memory space is master, and it can help slave to boot from master's memory space. When boot from PCIE, slave's core should be in holdoff after powered on for some specific requirements. Master will release the slave's core at the right time by PCIE interface. Environment and requirement: master: 1. NOR flash for its own u-boot image, ucode and ENV space. 2. Slave's u-boot image is in master NOR flash. 3. Normally boot from local NOR flash. 4. Configure PCIE system if needed. slave: 1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV. 2. Boot location should be set to one PCIE interface by RCW. 3. RCW should configure the SerDes, PCIE interfaces correctly. 4. Must set all the cores in holdoff by RCW. 5. Must be powered on before master's boot. For the master module, need to finish these processes: 1. Initialize the PCIE port and address space. 2. Set inbound PCIE windows covered slave's u-boot image stored in master's NOR flash. 3. Set outbound windows in order to configure slave's registers for the core's releasing. 4. Should set the environment variable "bootmaster" to "PCIE1", "PCIE2" or "PCIE3" using the following command: setenv bootmaster PCIE1 saveenv Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Get rid of the CONFIG_SRIOBOOT_SLAVE_PORTx macroLiu Gang2012-08-23-3/+0
| | | | | | | | | | | | | | | | When compile the slave image for boot from SRIO, no longer need to specify which SRIO port it will boot from. The code will get this information from RCW and then finishes corresponding configurations. This has the following advantages: 1. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just rewrite the new RCW with selected port, then the code will get the port information by reading new RCW. 2. It will be easier to support other boot location options, for example, boot from PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build targetLiu Gang2012-08-23-2/+57
| | | | | | | | | | | | | | | | | | | | | | Get rid of the SRIOBOOT_MASTER build target, and to support for serving as a SRIO boot master via environment variable. Set the environment variable "bootmaster" to "SRIO1" or "SRIO2" using the following command: setenv bootmaster SRIO1 saveenv The "bootmaster" will enable the function of the SRIO boot master, and this has the following advantages compared with SRIOBOOT_MASTER build configuration: 1. Reduce a build configuration item in boards.cfg file. No longer need to build a special image for master, just use a normal target image and set the "bootmaster" variable. 2. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just set the corresponding value to "bootmaster" based on the using SRIO port. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet: fix compile error when CONFIG_SYS_NO_FLASH is definedShaohui Xie2012-08-08-0/+5
| | | | | | | | | | ENV location compile logic is wrong, and when CONFIG_SYS_NO_FLASH is defined and non-NOR u-boot is building, it will cause compile error. Also, add CONFIG_SYS_FLASH_USE_BUFFER_WRITE for p2041, which will improve NOR flash write performance. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: Add USB device-tree fixup for various platformsramneek mehresh2012-07-06-1/+7
| | | | | | | Add USB device-tree fixup for following platforms: MPC8536DS, P1022DS, P1023RDS, P2020COME, P2020DS, P2041RDB, P3060QDS Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-20-1/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* powerpc/p2041rdb: add env in NAND supportShaohui Xie2012-04-24-0/+5
| | | | | | | Add env in NAND support when boot from NAND. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/p2041rdb: add NAND and NAND boot supportShaohui Xie2012-04-24-3/+51
| | | | | | | | New P2041RDB board will add a NAND chip, so add support for NAND and NAND boot. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* sdhc_boot: Introduce CONFIG_FSL_FIXED_MMC_LOCATION optionFabio Estevam2012-02-12-0/+1
| | | | | | | | | | | | | | | | | | | Since commit 97039ab98 (env_mmc: Allow board code to override the environment address) mmc_get_env_addr is a weak-aliased function in common/env_mmc.c The mmc_get_env_addr implementation that exists at board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards, but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined. Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate this config option on their board file. This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Stefano Babic <sbabic@denx.de>
* powerpc/85xx: clean up and document the QE/FMAN microcode macrosTimur Tabi2011-11-29-6/+10
| | | | | | | | | | | | | | | | | | | | Several macros are used to identify and locate the microcode binary image that U-boot needs to upload to the QE or Fman. Both the QE and the Fman use the QE Firmware binary format to package their respective microcode data, which is why the same macros are used for both. A given SOC will only have a QE or an Fman, so this is safe. Unfortunately, the current macro definition and usage has inconsistencies. For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address of NAND. There's no way to know by looking at a variable how it's supposed to be used. In the future, the code which uploads QE firmware and Fman firmware will be merged. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.hTimur Tabi2011-11-29-3/+2
| | | | | | | | | | | Macro CONFIG_FSL_SATA_V2 is defined if the SOC has a V2 Freescale SATA controller, so it should be defined in config_mpc85xx.h instead of the various board header files. So now CONFIG_FSL_SATA_V2 is always defined on the P1013, P1022, P2041, P3041, P5010, and P5020. It was already defined for the P1010 and P1014. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* common: cosmetic: CONFIG_BOOTFILE checkpatch complianceJoe Hershberger2011-10-22-1/+1
| | | | | | | | | Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
* common: cosmetic: CONFIG_ROOTPATH checkpatch complianceJoe Hershberger2011-10-22-1/+1
| | | | | | | | | Remove MK_STR from places that consume CONFIG_ROOTPATH to force all definitions to be string literals. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
* powerpc/85xx: Add support for RMan LIODN initializationKumar Gala2011-10-18-0/+1
| | | | | | | | | This patch is intended to initialize RMan LIODN related registers on P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* board configs: drop NET_MULTI referencesMike Frysinger2011-10-05-1/+0
| | | | | | | Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* powerpc/p2041rdb: set sysclk according to status of physical switch SW1Shaohui Xie2011-10-03-1/+4
| | | | | | | | | | | | | P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8], software need to read the SW1 status to decide what the sysclk needs. SW1[8~6] : frequency 0 0 1 : 83.3MHz 0 1 0 : 100MHz others: 66.667MHz Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/p2041rdb: Add ethernet support on P2041RDB boardMingkai Hu2011-09-29-1/+5
| | | | | | | | | | | | | | Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board. The five dTSEC can be routed to two on-board RGMII phy, three on-board SGMII phy or four SGMII phy on SGMII riser card according to different serdes protocol configuration and board lane configuration. Also updated the device tree to direct the Fmac MAC to the correct PHY. Removed CONFIG_SYS_FMAN_FW as its not used anywhere. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macrosTimur Tabi2011-09-29-14/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS. This is necessary for the assembly-language code that relocates CCSR, since the assembler does not understand 64-bit constants. CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it should not be defined in a board header file. Similarly, CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so it should also not be defined in the board header file. CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT, and so CCSR will not be relocated. Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot builds (e.g. NAND) are required to relocate CCSR only during the last stage (i.e. the "real" U-Boot). All other stages should define CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated. README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/p2041rdb: Enable SATA supportMingkai Hu2011-07-29-0/+20
| | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/p2041rdb: Enable backside L2 cache supportMingkai Hu2011-07-29-0/+2
| | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/p2041rdb: Add p2041rdb board supportMingkai Hu2011-07-17-0/+624
P2041RDB Specification: ----------------------- Memory subsystem: * 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus) * 128 Mbyte NOR flash single-chip memory * 256 Kbit M24256 I2C EEPROM * 16 Mbyte SPI memory * SD connector to interface with the SD memory card Ethernet: * dTSEC1: connected to the Vitesse SGMII PHY (VSC8221) * dTSEC2: connected to the Vitesse SGMII PHY (VSC8221) * dTSEC3: connected to the Vitesse SGMII PHY (VSC8221) * dTSEC4: connected to the Vitesse RGMII PHY (VSC8641) * dTSEC5: connected to the Vitesse RGMII PHY (VSC8641) PCIe: * Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1 * Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2 SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces I2C: * I2C1: Real time clock, Temperature sensor, Memory module * I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2 UART: supports two UARTs up to 115200 bps for console Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-06 21:24:01 +0000