summaryrefslogtreecommitdiff
path: root/include/configs/MVBLM7.h
Commit message (Collapse)AuthorAgeLines
* COMMON: Use __stringify() instead of MK_STR()Marek Vasut2012-10-15-13/+13
| | | | | | | | | Kill multiple occurances and redeclaration of MK_STR in favor of __stringify(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-20-1/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mpc83xx: Cleanup usage of LBC constantsJoe Hershberger2011-11-03-7/+8
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Cleanup usage of DDR constantsJoe Hershberger2011-11-03-1/+4
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Cleanup usage of BAT constantsJoe Hershberger2011-11-03-7/+6
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: cosmetic: MVBLM7.h checkpatch complianceJoe Hershberger2011-11-03-40/+76
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* board configs: drop NET_MULTI referencesMike Frysinger2011-10-05-1/+0
| | | | | | | Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated valueWolfgang Denk2010-10-26-2/+1
| | | | | | | | | | | | | | | | | | CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org>
* Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZEWolfgang Denk2010-10-26-2/+2
| | | | | | | | | | | | | | | | | | CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be some end address; to make the meaning more clear we rename it into CONFIG_SYS_INIT_RAM_SIZE No other code changes are performed in this patch, only minor editing of white space (due to the changed length) and the comments was done, where noticed. Note that the code for the PATI and cmi_mpc5xx board configurations looks seriously broken. Last known maintainers on Cc: Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Denis Peter <d.peter@mpl.ch> Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch> Acked-by: Kumar Gala <galak@kernel.crashing.org>
* MVBLM7: make TSEC2 work again.Andre Schwarz2010-10-23-1/+1
| | | | | | | SICRH has been misconfigured, i.e. TSEC2 clock + D[0:3] are GPIOs. Fix this to be RGMII signals again. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
* powerpc: Cleanup BOOTFLAG_* referencesPeter Tyser2010-10-18-9/+0
| | | | | | | | | | | | Now that warm booting is not supported, there isn't a need for the BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them. Note that this change makes the board info bd_bootflags field useless. It will always be set to 0, but we leave it around so that we don't break the board info structure that some OSes are expecting to be passed from U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Makefile: move all Power Architecture boards into boards.cfgWolfgang Denk2010-10-18-1/+3
| | | | | | | | | | Clean up Makefile, and drop a lot of the config.mk files on the way. We now also automatically pick all boards that are listed in boards.cfg (and with all configurations), so we can drop the redundant entries from MAKEALL to avoid building these twice. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-18-1/+1
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernelsIra W. Snyder2010-09-23-2/+2
| | | | | | | | | | | | | | Newer Linux kernels can overrun the initial memory window used for booting with their BSS area. When this happens, they overwrite the FDT and silently fail to boot. On e300 CPUs, the Linux kernel uses an initial BAT covering the first 256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value allowed by Linux. This will allow very large kernels to boot. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Remove unused CONFIG_SERIAL_SOFTWARE_FIFO featureStefan Roese2010-09-23-1/+0
| | | | | | | | | This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO feature from U-Boot. It has only been implemented for PPC4xx and was not used at all. So let's remove it and make the code smaller and cleaner. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* mpc83xx/mvBLM7: add usb commands and cleanup.Andre Schwarz2010-05-07-0/+6
| | | | | | | | | Add USB commands. Rename autoscript to bootscript. Add automatic bootscript image generation to makefile. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: turn on icache in core initialization to improve u-boot boot timeKim Phillips2010-04-22-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | before, MPC8349ITX boots u-boot in 4.3sec: column1 is elapsed time since first message column2 is elapsed time since previous message column3 is the message 0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX 0.000 0.000: 0.000 0.000: Reset Status: 0.000 0.000: 0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz 0.032 0.000: Board: Freescale MPC8349E-mITX 0.032 0.000: UPMA: Configured for compact flash 0.032 0.000: I2C: ready 0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz) 1.516 1.456: FLASH: 16 MB 2.641 1.125: PCI: Bus Dev VenId DevId Class Int 2.652 0.011: 00 10 1095 3114 0180 00 2.652 0.000: PCI: Bus Dev VenId DevId Class Int 2.652 0.000: In: serial 2.652 0.000: Out: serial 2.652 0.000: Err: serial 2.682 0.030: Board revision: 1.0 (PCF8475A) 3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic 3.080 0.000: TSEC0, TSEC1 4.300 1.219: IDE: Bus 0: .** Timeout ** after, MPC8349ITX boots u-boot in 3.0sec: 0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX 0.010 0.000: 0.010 0.000: Reset Status: 0.010 0.000: 0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz 0.017 0.000: Board: Freescale MPC8349E-mITX 0.038 0.020: UPMA: Configured for compact flash 0.038 0.000: I2C: ready 0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz) 0.260 0.222: FLASH: 16 MB 1.390 1.130: PCI: Bus Dev VenId DevId Class Int 1.390 0.000: 00 10 1095 3114 0180 00 1.390 0.000: PCI: Bus Dev VenId DevId Class Int 1.400 0.010: In: serial 1.400 0.000: Out: serial 1.400 0.000: Err: serial 1.400 0.000: Board revision: 1.0 (PCF8475A) 1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic 1.832 0.000: TSEC0, TSEC1 3.038 1.205: IDE: Bus 0: .** Timeout ** also tested on these boards (albeit with a less accurate boottime measurement method): seconds: before after 8349MDS ~2.6 ~2.2 8360MDS ~2.8 ~2.6 8313RDB ~2.5 ~2.3 #nand boot 837xRDB ~3.1 ~2.3 also tested on an 8323ERDB. v2: also remove the delayed icache enablement assumption in arch ppc's board.c, and add a CONFIG_MPC83xx define in the ITX config file for consistency (even though it was already being defined in 83xx' config.mk). Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: enable command line autocompletionKim Phillips2010-04-22-0/+1
| | | | | | because it's convenient. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfieldsKim Phillips2009-09-26-1/+2
| | | | | | | | | | | | | | | | | | | some LCRR bits are not documented throughout the 83xx family RMs. New board porters copying similar board configurations might omit setting e.g., DBYP since it was not documented in their SoC's RM. Prevent them bricking their board by retaining power on reset values in bit fields that the board porter doesn't explicitly configure via CONFIG_SYS_<registername>_<bitfield> assignments in the board config file. also move LCRR assignment to cpu_init_r[am] to help ensure no transactions are being executed via the local bus while CLKDIV is being modified. also start to use i/o accessors. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Remove deprecated 'autoscr' command/variablesPeter Tyser2009-09-22-7/+7
| | | | | | | | | | | | | | | The more standard 'source' command provides identical functionality to the autoscr command. Environment variable names/values on the MVBC_P, MVBML7, kmeter1, mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'. The 'autoscript' and 'autoscript_uname' environment variables are also removed. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Heiko Schocher <hs@denx.de>
* Use common code for Matrix Vision boardsAndré Schwarz2009-08-28-29/+20
| | | | | | | Clean up existing boards (mvBC-P/MPC5200 and mvBL-M7/MPC8343) by using common code. Signed-off-by: André Schwarz <andre.schwarz@matrix-vision.de>
* mpc83xx: CONFIG_83XX_GENERIC_PCI is now synonymous with CONFIG_PCI; remove ↵Kim Phillips2009-07-27-1/+0
| | | | | | the former Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* remove _IO_BASE and KSEG1ADDR from board configuration filesTimur Tabi2009-07-11-2/+0
| | | | | | | | | | | | | | | | The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet driver, but the code that used that macro was removed over a year ago, so board configuration files no longer need to define it. The _IO_BASE macro is also automatically defined to 0 if it isn't already set, so there's no need to define that macro either in the board configuration files. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]xPeter Tyser2009-06-12-1/+1
| | | | | | | | Use the standard lowercase "x" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xxPeter Tyser2009-06-12-1/+1
| | | | | | | | Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* i2c: Remove deprecated individual i2c commandsPeter Tyser2009-06-12-1/+0
| | | | | | | | | | | | | The following individual I2C commands have been removed: imd, imm, inm, imw, icrc32, iprobe, iloop, isdram. The functionality of the individual commands is still available via the 'i2c' command. This change only has an impact on those boards which did not have CONFIG_I2C_CMD_TREE defined. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Add "source" command; prepare removal of "autoscr" commandWolfgang Denk2009-04-03-6/+6
| | | | | | | | | | | | | | | | | | | | | According to the doc/feature-removal-schedule.txt, the "autoscr" command will be replaced by the "source" command in approximately 6 months from now. This patch prepares this change and starts a 6 month transition period as follows: - The new "source" command has been added, which implements exactly the same functionlaity as the old "autoscr" command before - The old "autoscr" command name is kept as an alias for compatibility - Command sequences, script files atc. have been adapted to use the new "source" command - Related environment variables ("autoscript", "autoscript_uname") have *not* been adapted yet; these will be renamed resp. removed in a separate patch when the support for the "autoscr" command get's finally dropped. Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc83xx: Set guarded bit on BAT that covers the end of the address spaceScott Wood2009-04-01-1/+2
| | | | | | | | | | | | | | | | | The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of address space; however, not all of this space is covered by a device. In particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped at the far end of the address space. In zlib, there is a loop that references p[-1] if p is non-NULL. Under some circumstances, this leads to the CPU speculatively loading from 0xfffffff8 if p is NULL. This leads to a machine check. Signed-off-by: Scott Wood <scottwood@freescale.com> continuation to the remaining mpc83xx boards that suffer from the same problem. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Removed unused CONFIG_L1_INIT_RAM symbol.Jon Loeliger2008-12-01-1/+0
| | | | | | | Prevent further viral propogation of the unused symbol CONFIG_L1_INIT_RAM by just removing it. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-149/+149
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD2008-09-10-6/+6
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-10-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* change mvBL-M7 default env and move to vendor subdirAndre Schwarz2008-08-25-27/+29
| | | | | | | fix mvBL-M7 config and move to matrix_vision subdir Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* drivers/mtd: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2008-08-13-1/+1
| | | | | | rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* update mvBL-M7 board configAndre Schwarz2008-07-07-2/+3
| | | | | | | update mvBL-M7 config file to use UBOOT_VERSION and define CONFIG_HIGH_BATS. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
* Coding Style CleanupWolfgang Denk2008-06-28-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc83xx: MVBLM7: minor build fixupsKim Phillips2008-06-10-1/+1
| | | | Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* add MPC8343 based board mvBlueLYNX-M7 (doc+config)Andre Schwarz2008-06-10-0/+479
Add MPC8343 based board mvBlueLYNX-M7. It's a single board stereo camera system. Please read doc/README.mvblm7 for details. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>