| Commit message (Collapse) | Author | Age | Lines |
|---|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| | |
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
| |/
|
|
|
|
|
|
|
|
|
| |
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| |
|
|
|
|
|
| |
Also fixes some commmand for 8641 HPCN ramboot case.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| |
|
|
|
|
|
|
| |
Introduced COFIG_FSL_I2C to select the common FSL I2C driver.
And removed hard i2c path from a few u-boot.lds scipts too.
Minor whitespace cleanups along the way.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| |
|
|
|
|
|
| |
in an effort to begin to unify the umpteen FSL I2C drivers that
are all otherwise very similar.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| | |
|
| |
|
|
|
|
|
| |
Remove PEX fluff commands.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| |
|
|
| |
Signed-off-by:Jason Jin<jason.jin@freescale.com>
|
| |
|
|
| |
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
|
| |
|
|
| |
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
| |
|
|
| |
Signed-off-by:Jason Jin <Jason.jin@freescale.com>
|
| |
|
|
|
| |
signed-off-by: Jason Jin <Jason.Jin@freescale.com>
signed-off-by: Wei Zhang <wei.zhang@freescale.com>
|
| |
|
|
| |
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
| | |
|
| | |
|
| |
|
|
|
|
|
|
| |
Enable the CFI driver.
Remove bogus LAWBAR7 cruft.
Use correct TEXT_BASE, Fixup load script.
Enable SPD EEPROM during DDR setup.
Use generic RFC 1918 IP addresses by default.
|
| |
|
|
|
|
|
| |
Removed //-style comments.
Use 80-column lines.
Remove trailing whitespace.
Remove dead code and debug cruft.
|
| |
|
