| Commit message (Collapse) | Author | Age | Lines |
... | |
|
|
|
|
|
|
| |
All the 85xx and 86xx UM describe the register as timing_cfg_3
not as ext_refrec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
|
|
|
|
|
|
| |
Without an actual supported video card hooked up, enabling
the CONFIG_VIDEO by default just makes it look broken by
routing all console output to the video card. Don't.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
| |
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
|
|
| |
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
|
|
|
|
| |
Enable command-line editing for all MPC86xx boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Convert the board/freescale/common/Makefile to use
CONFIG_* options to select which files to conditionally
compile into the board/freescale/common library rather
than conditionally compiling entire files.
Now handles::
CONFIG_FSL_PIXIS
CONFIG_FSL_DIU_FB
CONFIG_PQ_MDS_PIB
CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
|
|
|
| |
Use driver/net/uli526x.c as MPC8610HPCD default Ethernet driver.
Remove unused ethernet CONFIG_ options.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
|
| |
Just use the standard defines in asm/cache.h.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
|
|
|
|
| |
Assumes the presence of the aliases node in the DTS to
locate the pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
| |
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
| |
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add cfb console support to FSL 8610 DIU driver.
Inspect board version from PIXIS to obtain correct pixel format.
Use #define CONFIG_VIDEO in config file to enable fb console.
To switch monitor, set monitor variable to
0 - DVI, 1 - Single link LVDS, 2 - Double link LVDS
followed by "diufb init".
Preserve logo bitmap at the top of the fb console.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
1280x1024 and 1024x768 @ 32 bpp are supported now.
DVI, Single-link LVDS, Double-link LVDS are all supported.
Environmental variable "monitor" is used to specify monitor port.
A new command "diufb" is introduced to reinitialize monitor
and display a BMP file in the memory. So far, 1-bit, 4-bit,
8-bit and 24-bit BMP formats are supported.
diufb init
- initialize the diu driver
Enable the port specified in the environmental variable "monitor"
diufb addr
- display bmp file in memory.
The bmp image should be no bigger than the resolution, 1280x1024
for DVI and double-link LVDS, 1024x768 for single-link LVDS.
Note, this driver allocate memory but doesn't free it after use
It is written on purpose -- to avoid a failure of reallocation
due to memory fragement.
ECC of DDR is disabled for DIU performance. L2 data cache is also disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon loeliger <jdl@freescale.com>
|
|
|
|
|
|
| |
One may #define ENV_DEBUG to get them back again.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
|
|
| |
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
|
|
|
|
|
|
| |
The address in the BAT register is aligned with the BAT size.
The original definition actually did not define BAT for PCIE2 IO.
This patch fix this.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
|