| Commit message (Collapse) | Author | Age | Lines |
|
|
|
| |
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
|
|
|
|
|
|
|
|
| |
bootdelay set to -1 'permanently' disables autobooting, even if
bootcmd is specified. Change to a positive value to allow
autobooting when a bootcmd is set.
Reported-by: Coray Tate <Coray.Tate@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
| |
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
| |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
| |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
| |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
| |
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now. Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
|
|
|
|
|
|
|
|
| |
this seems as a good compromise between human memory, typing,
and last but not least, to accommodate for current and future kernel bloat.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes eeprom page size so that you can now write more than
64 bytes at a time.
It also makes the board take MAC addresses, if found, from EEPROM.
User should place up to 4 addresses at offset 0x7f00, for
eth{,1,2,3}addr. Any unused addresses should be zero. This group of
four six-byte values should have it's CRC at the end. crc32 and
eeprom commands can be used to accomplish this.
If CRC fails, MAC addresses come from the environment. If CRC
succeeds, the environment is overwritten at startup.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 55774b512fdf63c0516d441cc5da7c54bbffb7f2 broke the onboard USB
controller on the PCI bus in Linux on the MPC8323ERDB.
This fixes it by defining CONFIG_PCI_SKIP_HOST_BRIDGE in the board's
config file.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
| |
There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
| |
Use available shift/mask macros to define DDR configuration.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
|
| |
Remove the "#undef DEBUG" line from all Freescale 83xx board header files.
The inclusion of this line makes it impossible to enable debug code in
other source files, because "#define DEBUG" typically needs to be defined
before any header files are included.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
|
|
|
|
| |
continuation of commit b96c83d4ae475a70ef2635cd0e748174c44c8601
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
| |
clean up the cache config from configs.h of board
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
|
| |
the new libfdt code only updates eth0 if CONFIG_HAS_ETH0
is defined; add the define to the missing board configs.
Thanks to Emilian Medve for finding this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
|
| |
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
|
|
|
|
|
| |
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
currently-defined 83xx boards. This change guarantees that the environment
will be located on the first flash sector after the U-Boot image.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|