summaryrefslogtreecommitdiff
path: root/include/configs/MPC8315ERDB.h
Commit message (Collapse)AuthorAgeLines
* mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfieldsKim Phillips2009-09-26-1/+2
| | | | | | | | | | | | | | | | | | | some LCRR bits are not documented throughout the 83xx family RMs. New board porters copying similar board configurations might omit setting e.g., DBYP since it was not documented in their SoC's RM. Prevent them bricking their board by retaining power on reset values in bit fields that the board porter doesn't explicitly configure via CONFIG_SYS_<registername>_<bitfield> assignments in the board config file. also move LCRR assignment to cpu_init_r[am] to help ensure no transactions are being executed via the local bus while CLKDIV is being modified. also start to use i/o accessors. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: accommodate larger kernel sizes by defaultKim Phillips2009-08-21-2/+2
| | | | | | | linux mpc83xx_defconfig kernels are getting bigger, accommodate for their growth by adjusting default load and fdt addresses. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: CONFIG_83XX_GENERIC_PCI is now synonymous with CONFIG_PCI; remove ↵Kim Phillips2009-07-27-2/+1
| | | | | | the former Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: MPC8315ERDB: Use hwconfig for board type selectionAnton Vorontsov2009-07-16-0/+1
| | | | | | | This patch simply converts the board to the hwconfig infrastructure. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: set 64BIT_VSPRINTF for boards using nand_utilKim Phillips2009-07-14-0/+1
| | | | | | | | | | | When enabling NAND support for a board, one must also define CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c for correct output. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Cc: Dave Liu <daveliu@freescale.com> Cc: Ron Madrid <ron_madrid@sbcglobal.net> Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: 8315erdb: Add USB related CONFIGsVivek Mahajan2009-06-12-1/+10
| | | | | | | | | This patch adds CONFIGs for enabling USB in mpc8315erdb and also adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its Copyright. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* 83xx: Replace CONFIG_MPC83[0-9]X with MPC83[0-9]xPeter Tyser2009-06-12-1/+1
| | | | | | | | Use the standard lowercase "x" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xxPeter Tyser2009-06-12-1/+1
| | | | | | | | Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENVMike Frysinger2009-02-18-1/+1
| | | | | | | | The CONFIG_CMD_ENV option controls enablement of the `saveenv` command rather than a generic "env" command, or anything else related to the environment. So, let's make sure the define is named accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'next'Kim Phillips2009-01-23-0/+21
|\
| * mpc83xx: Add PCI-E support for MPC8315ERDB boardsAnton Vorontsov2009-01-21-0/+21
| | | | | | | | | | | | | | | | MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's support them. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPSWolfgang Grandegger2009-01-23-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and changes the default from 8 to 1 for the legacy and the new MTD NAND layer. This allows to remove all NAND_MAX_CHIPS definitions in the board config files because none of the boards use multi chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440 define #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE but that's bogus and did not work anyhow. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | mpc83xx: enable eLBC NAND support for MPC8315ERDB boardDave Liu2009-01-23-5/+7
|/ | | | Signed-off-by: Dave Liu <daveliu@freescale.com>
* mpc83xx: Improve the performance of DDR memoryHoward Gregory2008-11-19-6/+6
| | | | | | | | | | | | | modify the CAS timings. my understanding is that these settings decrease various wait times in the DDR interface. Because these wait times are in clock cycles, and the DDR clock on the 8315 RDB runs slower than on some other 83xx platforms, we can dial down these values without a problem, thereby decreasing the latency of memory a little. Signed-off-by: Howard Gregory <Greg.Howard@freescale.com> Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-18-156/+156
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* mpc83xx: add h/w flash protection to board configsKim Phillips2008-09-24-0/+1
| | | | | | | | the operating system may leave flash in a h/w locked state after writing. This allows u-boot to continue to write flash by enabling h/w unlocking by default. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD2008-09-10-5/+5
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-10-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHEREJean-Christophe PLAGNIOL-VILLARD2008-09-10-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Merge branch 'next'Kim Phillips2008-08-25-0/+2
|\
| * 83xx: mpc8315erdb: add support for switching between ULPI/UTMI USB PHYsAnton Vorontsov2008-07-16-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Freescale ships MPC8315E-RDB boards either with TSEC1 and USB UTMI support, or without TSEC1 but with USB ULPI PHY support in addition. With this patch user can specify desired USB PHY. Also, it seems that we can't distinguish the two boards in software, so user have to set `mpc8315erdb' environment variable to either 'tsec1' (TSEC1 enabled) or `ulpi' (board with ULPI PHY, TSEC1 disabled), so that Linux will not probe for TSEC1. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | drivers/mtd: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2008-08-13-1/+1
|/ | | | | | rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 83xx/85xx: further localbus cleanupsAnton Vorontsov2008-06-10-1/+1
| | | | | | | | | | | | | move the BRx_* and ORx_* left behind in mpc85xx.h The same is needed for mpc8xx.h and mpc8260.h (defines are almost the same, just few differences which needs some attention though). But the bad news for mpc8xx and mpc8260 is that there are a lot of users of these defines. So this cleanup I'll leave for the "better times". Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* PPC: Create and use CONFIG_HIGH_BATSBecky Bruce2008-06-03-0/+1
| | | | | | | | | | | Change all code that conditionally operates on high bat registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS instead of the myriad ways this is done now. Define the option for every config for which high bats are supported (and enabled by early boot, on parts where they're not always enabled) Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc83xx: bump loadaddr over fdtaddr to 0x500000Kim Phillips2008-04-25-1/+1
| | | | | | | | this seems as a good compromise between human memory, typing, and last but not least, to accommodate for current and future kernel bloat. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Dave Liu <daveliu@freescale.com>
* mpc83xx: enable the SATA interface on mpc8315 rdb and mpc837x rdb boardsKim Phillips2008-03-28-0/+23
| | | | Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Set PCI I/O bus-address base to zero.Scott Wood2008-03-25-1/+1
| | | | | | | | | | The device trees for these boards describe PCI I/O as starting from address zero from the device's perspective. Placing I/O elsewhere may cause problems with certain PCI boards, and may cause problems with Linux. Signed-off-by: Scott Wood <scottwood@freescale.com>
* Get rid of "#undef DEBUG" from board config files.Wolfgang Denk2008-02-12-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc83xx: Add the support for MPC8315ERDB boardDave Liu2008-01-16-0/+547
The features list: - Boot from NOR Flash - DDR2 266MHz hardcoded configuration - Local bus NOR Flash R/W operation - I2C, UART, MII and RTC - eTSEC0/1 support - PCI host Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
generated by cgit v1.1 at 2024-07-15 15:23:18 +0000