| Commit message (Collapse) | Author | Age | Lines |
|---|
| |
|
|
|
|
|
|
|
|
| |
Writes in u-boot are so rare, and the logic to know when is
the last write and do a flush only there is sufficiently
difficult. Just do a flush after every write. This incurs,
usually, one extra flush when the rare writes do happen.
Signed-off-by: Marc Jones <marc.jones@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
|
|
| |
This patch adds support for the esd CPCI-HD/2 board to u-boot for CPCI-CPU/750.
As the primary devices on the CPCI-HD/2 board are connected to device 1 and 3,
the device must be swapped.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
|
| |
|
|
| |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds a hook whereby a board-specific routine can be called to
configure hardware for a PIO mode. The prototype for the board-specific
routine is:
int inline ide_set_piomode(int pio_mode)
ide_set_piomode should be prepared to configure hardware for a pio_mode
between 0 and 6, inclusive. It should return 0 on success or 1 on failure.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
|
| |
|
|
|
|
|
|
| |
This patch removes some enums from ata.h and replaces them with an
include of libata.h. This way, we eliminate duplicated code, and
prevent errors whereby the different versions could be out of sync.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Bridge, ICH-5, ICH-6 and ICH-7.
Implementation:
1. Code is divided in to two files. All functions, which are
controller specific are kept in "drivers/ata_piix.c" file and
functions, which are not controller specific, are kept in
"common/cmd_sata.c" file.
2. Reading and Writing from the S-ATA drive is done using PIO method.
3. Driver can be configured for 48-bit addressing by defining macro
CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
addressing.
4. S-ATA read function is hooked to the File system, commands like
ext2ls and ext2load file can be used. This has been tested.
5. U-Boot command "SATA_init" is added, which initializes the S-ATA
controller and identifies the S-ATA drives connected to it.
6. U-Boot command "sata" is added, which is used to read/write, print
partition table and get info about the drives present. This I have
implemented in same way as "ide" command is implemented in U-Boot.
7. This driver is for S-ATA in native mode.
8. This driver does not support the Native command queuing and
Hot-plugging.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
- Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
- Added support for 64bit strtoul (CFG_64BIT_STRTOUL)
* Patch by Masami Komiya, 27 Feb 2004:
Fix rarpboot: add autoload by NFS
* Patch by Dan Eisenhut, 26 Feb 2004:
fix flash_write return value in saveenv
* Patch by Stephan Linz, 11 Dec 2003
expand config.mk to avoid trigraph warnings on NIOS
* Rename "BMS2003" board into "HMI10"
|
| |
|
|
|
|
|
|
| |
add I2C support; add support for DS1337 RTC
* Add CompactFlash support for BMS2003 board
* Add support for status LED on BMS2003 board
|
| |
|
|
|
|
|
| |
- add a return value for the fpga command
- add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT
is defined. If ide_preinit fails, ide_init is aborted.
- fix an endianess problem in fat.h
|
| |
|
