summaryrefslogtreecommitdiff
path: root/include/asm-arm
Commit message (Collapse)AuthorAgeLines
* at91: Introduction of at91sam9g45 SOC.Sedji Gaouaou2009-07-12-0/+307
| | | | | | | | | | | | AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz. It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of peripherals. The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. On the board you can find 2 USART, USB high speed, a 480*272 LG lcd, ethernet, gpio/joystick/buttons. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
* pxa: fix CKEN_B register bitsDaniel Mack2009-07-12-6/+6
| | | | | | | | The current defition for CKEN_B register bits is nonsense. Adding 32 to the shifted value is equal to '| (1 << 5)', and this bit is marked 'reserved' in the PXA docs. Signed-off-by: Daniel Mack <daniel@caiaq.de>
* pxa: add clock for system bus 2 arbiterDaniel Mack2009-07-12-0/+1
| | | | | | | This clock is needed for systems using the USB2 device unit or the 2d graphics accelerator. Signed-off-by: Daniel Mack <daniel@caiaq.de>
* arm: Kirkwood: bugfix: UART1 bar correctionPrafulla Wadaskar2009-07-12-1/+1
| | | | Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* Coding style cleanup; update CHANGELOGWolfgang Denk2009-07-07-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* MX31: Add NAND SPL boot support to i.MX31 PDK board.Magnus Lilja2009-07-06-0/+54
| | | | Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
* arm: Kirkwood: arch specific updated for ehci-Kirkwood driver supportPrafulla Wadaskar2009-07-06-0/+9
| | | | | | This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* arm nomadik: use 1000 as HZ value and rewrite timer codeAlessandro Rubini2009-07-06-0/+66
| | | | | | | | | | | | This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites timer code, which is now both correct and much smaller. Unused functions like udelay_masked() have been removed as no driver uses them, even the ones that are not currently active for this board. mtu.h is copied literally from the kernel sources. Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stericsson.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: Update mach-typesJean-Christophe PLAGNIOL-VILLARD2009-07-06-39/+1612
| | | | | | update against linux v2.6.30 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: Add CAN init functionDaniel Gorsulowski2009-07-06-0/+1
| | | | | | | | | To enable CAN init, CONFIG_CAN has to be defined in the board config file and at91_can_hw_init() has to be called in the board specific code. CAN is available on AT91SAM9263 and AT91CAP9 SoC. Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
* arm: Kirkwood: Correct header defineSimon Kagstrom2009-07-06-1/+1
| | | | | | Correct define typo (. -> ,) Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
* MX31: Add basic support for Freescale i.MX31 PDK board.Magnus Lilja2009-07-06-0/+2
| | | | | | | | | | | Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board). This patch assumes that some other program performs the actual NAND boot. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com> Acked-by: Fabio Estevam <fabioestevam@yahoo.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* move L2 cache enable/disable function to cache.c in the omap3 SoC directoryKim, Heung Jun2009-07-06-0/+4
| | | | | | Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> CC: Dirk Behme <dirk.behme@googlemail.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: Kirkwood: Basic SOCs supportPrafulla Wadaskar2009-07-06-0/+605
| | | | | | | | | | | | | | | | | | | | | | Kirkwood family controllers are highly integrated SOCs based on Feroceon-88FR131/Sheeva-88SV131/arm926ejs cpu core. SOC versions supported:- 1) 88F6281-A0 define CONFIG_KW88F6281_A0 2) 88F6192-A0 define CONFIG_KW88F6192_A0 Other supported features:- 1) get_random_hex() fucntion 2) PCI Express port initialization 3) NS16550 driver support Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed-by: Ronen Shitrit <rshitrit@marvell.com> Acked-by: Stefan Rose <sr@denx.de> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* arm: generic cache.h for ARM architecturesPrafulla Wadaskar2009-07-06-0/+41
| | | | | | | This patch is required for Kirkwood SoC support may be used by other ARM architectures Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* OMAP3EVM: fix typo. replace CS6 by CS5, no functionality changeMatthias Ludwig2009-07-06-2/+3
| | | | Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
* spi: Add Marvell Kirkwood SPI driverPrafulla Wadaskar2009-06-26-0/+56
| | | | | | This patch adds a SPI driver for the Marvell Kirkwood SoC's. Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* mx27: basic cpu supportIlya Yanok2009-06-21-0/+564
| | | | | | This patch adds generic code to support Freescale's i.MX27 SoCs. Signed-off-by: Ilya Yanok <yanok@emcraft.com>
* i.MX31: Create a common device file.Magnus Lilja2009-06-21-0/+3
| | | | Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
* ARM: Add macros.h to be used in assembler file.Jean-Christophe PLAGNIOL-VILLARD2009-06-21-0/+74
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* MX31: Add NAND SPL for i.MX31.Magnus Lilja2009-06-21-0/+5
| | | | | | | | | | | | | | | | | | This patch adds the NAND SPL framework needed to boot i.MX31 boards from NAND. It has been tested on a i.MX31 PDK board with large page NAND. Small page NANDs should work as well, but this has not been tested. Note: The i.MX31 NFC uses a non-standard layout for large page NANDs, whether this is compatible with a particular setup depends on how the NAND device is programmed by the flash programmer (e.g. JTAG debugger). The patch is based on the work by Maxim Artamonov. Signed-off-by: Maxim Artamonov <scn1874@yandex.ru> Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
* at91: unify nor boot supportJean-Christophe PLAGNIOL-VILLARD2009-06-21-0/+28
| | | | | | the lowlevel init sequence is the same so unify it Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* pm9263: use macro instead of hardcode value for the lowlevel_initJean-Christophe PLAGNIOL-VILLARD2009-06-21-0/+1
| | | | | | | optimize a few the RAM init Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* DaVinci Network Driver Updatess-paulraj@ti.com2009-06-15-1/+31
| | | | | | | | | | | | | | Different flavours of DaVinci SOC's have differences in their EMAC IP This patch does the following 1) Updates base addresses for DM365 2) Updates MDIO frequencies for DM365 and DM646x 3) Update EMAC wrapper registers for DM365 and DM646x Patch applies to u-boot-net git. the EMAC driver itself will be updated shortly to add support for DM365 and DM646x Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arch_misc_init support for ARM architecturesPrafulla Wadaskar2009-06-12-0/+1
| | | | | | | This patch is required for Kirkwood support may be used by other ARM architectures Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* at91: move cpu name define to arm/arch/ cpu headerJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+27
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* arm: unify interrupt initJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+1
| | | | | | | all arm init the IRQ stack the same way so unify it in lib_arm/interrupts.c and then call arch specific interrupt init Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM DaVinci: Minor Updates to base addressess-paulraj@ti.com2009-06-12-0/+6
| | | | | | | Patch adds base addresses for DaVinci DM365. Updated patches for DM365 will be posted soon. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3 Port kernel omap gpio interface.Tom Rix2009-06-12-0/+86
| | | | | | | | | Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot. The orignal source is in linux/arch/arm/plat-omap/gpio.c See doc/README.omap3 for instructions on use. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* ARM: Update mach-typesJean-Christophe PLAGNIOL-VILLARD2009-06-12-7/+1697
| | | | | | update against linux v2.6.29 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: display correct clock infoDavid Brownell2009-06-12-5/+0
| | | | | | | | | | | | Move the clock-rate dumping code into the cpu/.../davinci area where it should have been, enabled by CONFIG_DISPLAY_CPUINFO, updating the format and showing the DSP clock (where relevant). Switch boards to use the cpuinfo() hook for this stuff. Remove a few now-obsolete PLL #defines. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* arm: timer and interrupt init reworkJean-Christophe PLAGNIOL-VILLARD2009-06-12-0/+3
| | | | | | | | | | | | | | actually the timer init use the interrupt_init as init callback which make the interrupt and timer implementation difficult to follow so now rename it as int timer_init(void) and use interrupt_init for interrupt btw also remane the corresponding file to the functionnality implemented as ixp arch implement two timer - one based on interrupt - so all the timer related code is moved to timer.c Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* davinci: add basic dm355/dm350/dm335 supportDavid Brownell2009-06-12-17/+38
| | | | | | | | | | | | | Add some basic declarations for DaVinci DM355/DM350/DM335 support, keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the DM357 is very different; while the DM355 is like a DM355 without the MPEG/JPEG coprocessor). These have different peripherals than the DM6446, and some of the peripherals are at different addresses. Notably for U-Boot, there's no EMAC, and the NAND controller address is different Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* davinci: move psc support board-->cpuDavid Brownell2009-06-12-0/+8
| | | | | | | | Move DaVinci PSC support from board/* to cpu/* where it belongs. The PSC module manages clocks and resets for all DaVinci-family SoCs, and isn't at all board-specific. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
* ARM: fix PXA build by defining UP2OCRDaniel Mack2009-05-15-0/+4
| | | | | | | | | | | | | U-Boot does not currently build for PXA platforms with USB support enabled: usb.c:46: error: 'UP2OCR' undeclared (first use in this function) Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Markus Klotzbuecher <mk@denx.de> Edited commit message. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Fix e-mail address of Gary Jennejohn.Detlev Zundel2009-05-15-1/+1
| | | | Signed-off-by: Detlev Zundel <dzu@denx.de>
* OMAP3: Print correct silicon revisionSanjeev Premi2009-04-29-5/+9
| | | | | | | | | | The function display_board_info() displays incorrect silicon revision - based on the return value from function get_cpu_rev(). This patch fixes the problem. Signed-off-by: Sanjeev Premi <premi@ti.com>
* OMAP3: Remove unused board-typesSanjeev Premi2009-04-29-11/+0
| | | | | | | | | | | The board-types defined in struct omap3_sysinfo seem to be unused. The function display_board_info() is passed board type as an argument; which is ignored. This patch removes all uses of board-type, related definitions and functions. Signed-off-by: Sanjeev Premi <premi@ti.com>
* OMAP3: Use functions print_cpuinfo() and checkboard()Sanjeev Premi2009-04-29-1/+0
| | | | | | | | | | | | | | | Use the functions print_cpuinfo() and checkboard() to display the cpu and board specific information. These functions reuse content from the existing function display_board_info() - which has been removed. Also, updated the existig OMAP3 configurations to define: - CONFIG_DISPLAY_CPUINFO - CONFIG_DISPLAY_BOARDINFO Signed-off-by: Sanjeev Premi <premi@ti.com>
* at91: add support for the PM9263 board of Ronetix GmbHIlko Iliev2009-04-16-0/+105
| | | | | | | | | | The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD2009-04-16-11/+44
| | | | | | calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Support for PXA27X UDC.Remy Bohmer2009-04-06-53/+243
| | | | | | | | This Patch adds Support for PXA27X UDC. (Rebased to drivers/usb reorganisation) Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* arm: update co-processor 15 accessJean-Christophe PLAGNIOL-VILLARD2009-04-05-0/+84
| | | | | | import system.h from linux Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9: add watchdog supportJean-Christophe PLAGNIOL-VILLARD2009-04-04-0/+38
| | | | | Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* s3c4510b: move specific code to soc directoryJean-Christophe PLAGNIOL-VILLARD2009-03-29-3/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.Nicolas Ferre2009-03-22-1/+1
| | | | | | | | | | | | | | AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common macb initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-22-0/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common usb host initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-22-0/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common spi initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-22-0/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common serial initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-22-0/+34
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
generated by cgit v1.1 at 2024-12-05 02:16:55 +0000