summaryrefslogtreecommitdiff
path: root/drivers
Commit message (Collapse)AuthorAgeLines
* Merge branch 'next'Wolfgang Denk2010-04-01-112/+489
|\
| * Merge remote branch 'origin/master' into nextWolfgang Denk2010-03-29-1/+4
| |\
| * \ Merge branch 'next' of git://www.denx.de/git/u-boot-cfi-flash into nextWolfgang Denk2010-03-29-7/+86
| |\ \
| | * | cfi flash: add status polling method for amd flashThomas Chou2010-03-26-7/+86
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds status polling method to offer an alternative to data toggle method for amd flash chips. This patch is needed for nios2 cfi flash interface, where the bus controller performs 4 bytes read cycles for a single byte read instruction. The data toggle method can not detect chip busy status correctly. So we have to poll DQ7, which will be inverted when the chip is busy. This feature is enabled with the config def, CONFIG_SYS_CFI_FLASH_STATUS_POLL Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Stefan Roese <sr@denx.de>
| * | | Merge branch 'next' of git://git.denx.de/u-boot-coldfire into nextWolfgang Denk2010-03-28-27/+31
| |\ \ \
| | * | | ColdFire: Update uart_port_conf in serial driverTsiChung Liew2010-03-24-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Provide proper port passing from serial_init to uart_part_conf. Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
| | * | | add block write function to spartan3 slave serial loadWolfgang Wegner2010-03-24-25/+29
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using seperate function calls for each bit-bang of slave serial load can be painfully slow. This patch adds the possibility to supply a block write function that loads the complete block of data in one call (like it can already be done with Altera FPGAs). On an MCF5373L (240 MHz) loading an XC3S4000 this reduces the load time from around 15 seconds to around 3 seconds Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
| * | | at91: add hwecc method for nandNikolay Petukhov2010-03-23-0/+301
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a patch to use the hardware ECC controller of the AT91SAM9260 for the AT91 nand. Taken from the kernel 2.6.33. Signed-off-by: Nikolay Petukhov <Nikolay.Petukhov@gmail.com>
| * | | TI: Davinci: NAND Driver CleanupCyril Chemparathy2010-03-23-59/+69
| |/ / | | | | | | | | | | | | | | | | | | Modified to use IO accessor routines consistently. Eliminated volatile usage to keep checkpatch.pl happy. Signed-off-by: Cyril Chemparathy <cyril@ti.com>
| * | Merge remote branch 'origin/master' into nextWolfgang Denk2010-03-21-19/+19
| |\ \
| * | | mpc5xxx: Remove all references to MGT5100Detlev Zundel2010-03-21-19/+2
| | | | | | | | | | | | | | | | | | | | | | | | We do not support a processor that never reached a real customer. Signed-off-by: Detlev Zundel <dzu@denx.de>
| * | | video: Fix console display when splashscreen is usedMatthias Weisser2010-03-21-9/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a splashscreen is used the console scrolling used the scroll size as needed when a logo was displayed. This patch sets the scroll size to the whole screen if a splashscreen is shown. Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
* | | | net, fec_mxc: only setup the device enetaddr with eeprom valueHeiko Schocher2010-03-31-1/+0
| |_|/ |/| | | | | | | | | | | | | | | | | | | | Only fill the device enetaddr with the contents of the eeprom, do not program it in MAC address registers Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Ben Warren <biggerbadderben@gmail.com>
* | | cfi_flash: precision and underflow problem in tout calculationRenato Andreola2010-03-25-1/+4
| |/ |/| | | | | | | | | | | | | | | With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000. Signed-off-by: Renato Andreola <renato.andreola@imagos.it> Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Stefan Roese <sr@denx.de>
* | mod change 755 => 644 for multiple filesThomas Weber2010-03-21-0/+0
| | | | | | | | | | | | | | | | I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;' Signed-off-by: Thomas Weber <swirl@gmx.li> Add some more: neither Makefile nor config.mk need execute permissions. Signed-off-by: Wolfgang Denk <wd@denx.de>
* | mxcmmc: fix warnings due to access 32 bit registers with 16 bit accessorsStefano Babic2010-03-21-18/+18
| | | | | | | | | | | | | | | | | | Some registers of the mxcmmc driver were accessed using 16 bit accessor functions, because only the LSB is significant. This is not needed and generates warnings. Signed-off-by: Stefano Babic <sbabic@denx.de>
* | Fix PCI_BASE_ADDRESS_5 handling in pci_hose_config_device()Wolfgang Denk2010-03-21-1/+1
| | | | | | | | | | | | Signed-off-by: FUJITA Kazutoshi <fujita@soum.co.jp> Signed-off-by: <wd@denx.de> Acked-by: Stefan Roese <sr@denx.de>
* | video: Fix console display when splashscreen is usedMatthias Weisser2010-03-13-9/+12
|/ | | | | | | | | If a splashscreen is used the console scrolling used the scroll size as needed when a logo was displayed. This patch sets the scroll size to the whole screen if a splashscreen is shown. Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
* Prepare v2010.03-rc1v2010.03-rc1Wolfgang Denk2010-03-12-6/+1
| | | | | | Coding style cleanup, update CHANGELOG. Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc82xx: Remove SL8245 board and the now orpahned sk98lin network driver.Detlev Zundel2010-03-12-45428/+0
| | | | | | | | | This code has compile problems and the company does not even exist any more. So we take the liberty to drop support for it. Signed-off-by: Detlev Zundel <dzu@denx.de> CC: Wolfgang Denk <wd@denx.de> CC: Ben Warren <biggerbadderben@gmail.com>
* Fix memory leak in mmc_read()Wolfgang Denk2010-03-11-1/+1
| | | | | | | | | There is be a path through mmc_read in drivers/mmc/mmc.c where malloc'd memory is not freed before exiting mmc_read: it occurs if mmc_set_blocklen() returns a non-zero value. Reported-by: Quentin Armitage <Quentin@Armitage.org.uk> Signed-off-by: Wolfgang Denk <wd@denx.de>
* fec_mxc: add MX25 supportJohn Rigby2010-03-07-3/+60
| | | | | | | | Use RMII for MX25 Add code to init gasket that enables RMII Signed-off-by: John Rigby <jcrigby@gmail.com> CC: Ben Warren <biggerbadderben@gmail.com>
* fec_mxc: cleanup and factor out MX27 dependenciesJohn Rigby2010-03-07-6/+9
| | | | | | | | | | | | | general cleanup move clock init to cpu_eth_init in cpu/arm926ejs/mx27/generic.c make MX27 specific phy init conditional on CONFIG_MX27 replace call to imx_get_ahbclk with one to imx_get_fecclk and define imx_get_fecclk in include/asm-arm/arch-mx27/clock.h Signed-off-by: John Rigby <jcrigby@gmail.com> CC: Ben Warren <biggerbadderben@gmail.com> CC: Fred Fan <fanyefeng@gmail.com> CC: Tom <Tom.Rix@windriver.com>
* Add support for Freescale MX25 SOCJohn Rigby2010-03-07-5/+5
| | | | | | | | | ARM926EJS core with MX31 peripherals. Signed-off-by: John Rigby <jcrigby@gmail.com> Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de> CC: Fred Fan <fanyefeng@gmail.com> CC: Tom <Tom.Rix@windriver.com>
* fsl_esdhc: add support for mx51 processorStefano Babic2010-03-07-48/+101
| | | | | | | | | The esdhc controller in the mx51 processor is quite the same as the one in some powerpc processors (MPC83xx, MPC85xx). This patches adapts the driver to support the arm mx51. Signed-off-by: Stefano Babic <sbabic@denx.de>
* MMC: add weak function to detect MMC/SD cardStefano Babic2010-03-07-0/+7
| | | | | | | | | | | Most controllers can check if there is a card in the slot. However, they require pins that could be not available because required by other functions and the detection of a card must be performed in another way. This patch adds a weak function that a board can implement to add its internal custom way to check the presence of a MMC/SD card. Signed-off-by: Stefano Babic <sbabic@denx.de>
* mmc: check correctness of the voltage mask in ocrStefano Babic2010-03-07-1/+9
| | | | | | | | | | Most cards do not answer if some reserved bits in the ocr are set. However, some controllers can set bit 7 (reserved for low voltages), but how to manage low voltages SD card is not yet specified. Signed-off-by: Stefano Babic <sbabic@denx.de>
* serial_mxc: add support for MX51 processorStefano Babic2010-03-07-6/+12
| | | | | | | The patch adds support for the Freescale mx51 processor. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Fred Fan <fanyefeng@gmail.com>
* ] fix monitor protection for CONFIG_MONITOR_IS_IN_RAMWolfgang Wegner2010-03-04-1/+2
| | | | | | | | | | For platforms with flash below ram addresses, the current check to activate monitor protection is wrong/insufficient. This patch fixes CONFIG_MONITOR_IS_IN_RAM for these systems by adding a check for this configuration. Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Stefan Roese <sr@denx.de>
* convert common files to new SoC accessJens Scharsig2010-02-12-6/+48
| | | | | | | | * add's a warning to all files, which need update to new SoC access * convert common files in cpu/../at91 and a lot of drivers to use c stucture SoC access Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add a new AT91 GPIO driverJens Scharsig2010-02-12-0/+215
| | | | | | | | | * add a real AT91 GPIO driver instead of header inline code * resolve the mixing of port and pins * change board config files to use new driver * add macros to gpio to realize backward compatibility Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* SPI: Fix 32 bit transfers in mxc_spi.cMagnus Lilja2010-02-12-0/+9
| | | | | | | | | | | | | | Commit f9b6a1575d9f1ca192e4cb60e547aa66f08baa3f, "i.MX31: fix SPI driver for shorter than 32 bit" broke 32 bit transfers. This patch makes single 32 bit transfer work again. Transfer lengths that are known not to work will abort and print an error message. Tested on i.MX31 Litekit and i.MX31 PDK using 32 bit transfers to the MC13783/ATLAS chip (using the 'date' command). Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
* TI DaVinci: Driver for the davinci SPI controllerSekhar Nori2010-02-12-0/+325
| | | | | | | | | This adds a driver for the SPI controller found on davinci based SoCs from Texas Instruments. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* fec_mxc: add support for MX51 processorStefano Babic2010-02-06-41/+32
| | | | | | | | The patch add support for the Freescale mx51 processor to the FEC ethernet driver. Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* NET: kirkwood-egiga smi access fixSiddarth Gore2010-02-06-6/+7
| | | | | | | | | | | | Although the datasheet mentions seperate smi registers for each port, using Port 1 smi register to access ethernet phys does not work. Hence only Port 0 smi register should be used to access all devices connected to the smi bus. This behavior is consistant with the mv643xx driver in the linux kernel. Signed-off-by: Siddarth Gore <gores@marvell.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* ns16550: kick watchdog while waiting for a characterLadislav Michl2010-02-03-0/+2
| | | | | | | | ns16550 busyloops waiting for incoming byte causing watchdog to reboot while waiting for a key press. A call to WATCHDOG_RESET in NS16550_getc loop fixes it. Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
* musb: Add host support for DM365 EVMPrathap Srinivas2010-02-03-2/+20
| | | | | | Add support for musb host on DM365 EVM. Signed-off-by: Prathap Srinivas <msprathap@ti.com>
* usb: musb: fix Blackfin DMA register paddingCliff Cai2010-02-03-1/+1
| | | | | | | | | The conversion from offsets to C structs lost a little padding in the DMA register map. Accessing endpoints other than ep0 with DMA would fail as the addresses wouldn't be adjusted correctly. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk2010-02-03-17/+18
|\
| * CFI: fix eraseregions numblocksLadislav Michl2010-02-02-17/+18
| | | | | | | | | | | | | | | | | | | | eraseregions numblocks was sometimes one less than actual, possibly producing erase regions with zero blocks. As MTD code touches eraseregions only if numeraseregions is greater that zero, allocate eraseregions only for non uniform erase size flash. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk2010-02-03-719/+2153
|\ \
| * | new at91_emac network driver (NET_MULTI api)Jens Scharsig2010-01-31-0/+499
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * add's at91_emac (AT91RM9200) network driver (NET_MULTI api) * enable driver with CONFIG_DRIVER_AT91EMAC * generic PHY initialization * modify AT91RM9200 boards to use NET_MULTI driver * the drivers has been tested with LXT971 Phy and DM9161 Phy at MII and RMII interface Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | Add EP93xx ethernet driverMatthias Kaehlcke2010-01-31-0/+798
| | | | | | | | | | | | | | | | | | | | | Added ethernet driver for EP93xx SoCs Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | 83xx, uec: split enet_interface in two variablesHeiko Schocher2010-01-31-109/+131
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There's no sensible reason to unite speed and interface type into one variable. So split this variable enet_interface into two vars: enet_interface_type, which hold the interface type and speed. Also: add the possibility for switching between 10 and 100 MBit interfaces on the fly, when running in FAST_ETH mode. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | TI: DaVinci: Updating EMAC driver for DM365, DM646x and DA8XXNick Thompson2010-01-31-95/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | The EMAC IP on DM365, DM646x and DA830 is slightly different from that on DM644x. This change updates the DaVinci EMAC driver so that EMAC becomes operational on SOCs with EMAC v2. Signed-off-by: Nick Thompson <nick.thompson@ge.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | macb: Fix mii_phy_read and mii_phy_write functionsSemih Hazar2010-01-31-77/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enabling CONFIG_CMD_MII in AVR32 boards was not possible due to compile errors. This patch fixes miiphy_read and miiphy_write functions and registers them properly. Signed-off-by: Semih Hazar <semih.hazar@indefia.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | tsec: Add TSEC_FIBER flagPeter Tyser2010-01-31-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TSEC_FIBER flag should be set when a PHY is operating with an external fiber interface. Currently it is only used to notify a user that the PHY is operating in fiber mode. A short description was also added to the other TSEC flag defines so that it is clear how they differ from one another. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | tsec: Add support for using the BCM5482 PHY in fiber modePeter Tyser2010-01-31-4/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | The BCM5482 PHY supports both copper and fiber as an ethernet medium. By enabling its copper/fiber mode auto-detection feature it can dynamically determine if it should be configured for copper or fiber. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | tsec: General cleanupPeter Tyser2010-01-31-345/+326
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - Cleanup formatting of phy_info structures - Fix lines > 80 chars - Fix some random indentation inconsistencies Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
| * | tsec: Make functions/data static when possiblePeter Tyser2010-01-31-43/+47
| | | | | | | | | | | | | | | | | | | | | This is generally good practice and saves ~150 bytes. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
generated by cgit v1.1 at 2024-12-20 01:19:16 +0000