| Commit message (Collapse) | Author | Age | Lines |
|
|
|
|
|
| |
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
|
|
|
|
|
|
|
| |
Tegra recently moved to the new I2C framework, which sets up I2C prior to
relocation, and prior to calling i2c_init_board(). This causes a crash on
Tegra boards.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| | |
Register arm_dcc with drivers/serial/serial.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Removed stdio structure ops support on arm_dcc
driver, and need to register with serial core
so-that it can access like remianing serial drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
FMAN firmware can be in NOR flash, NAND flash, SPI flash, MMC or even
remote. In case none of them is defined, set it to null.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|\ \ \
| |_|/
|/| | |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch have changed mipi dsi write functions' parameters correctly
so that type cast operations were removed. And mipi dsi payload is
composed with array of panel commands to improve readability.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch add an option to skip cfb console init for boards
who want to show a logo, but not use the cfb console. This is
needed for the siemens boards, which have a bmp bootlogo, but
do not need the cfb console.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: use '__weak int board_cfb_skip(void)']
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
without this patch the bdinfo command shows:
U-Boot# bd
arch_number = 0x000010DC
[...]
sp start = 0x8EF32F20
FB base = 0x00000000
with this patch it shows the address where the framebuffer
for this video driver start:
arch_number = 0x000010DC
[...]
sp start = 0x8EF32F20
FB base = 0x8EF3C788
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
to use this driver also on am335x based boards, the following
changes are made:
- struct lcd_ctrl_config lcd_cfg is now configurable
through board code
- controller base is configurable through define
DA8XX_LCD_CNTL_BASE. To be compatible with older
da8xx based boards: If this define is missing, the
DAVINCI_LCD_CNTL_BASE is used
- Determine LCD IP Version, and make the driver
working on lcd revision register values:
Version 1:
0x4C100102
Version 2:
0x4F200800
0x4F201000
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
the da8xx-fb driver works also on am335x boards. So move
the da8xx-fb.h file from arch/arm/include/asm/arch-davinci
to drivers/video, so this driver can used from am335x
based boards. Also add WVGA panel_type.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This is u-boot driver for L5F31188 panel.
I tested it in the board based on MIPI DSI with EXYNOS4 series, and it worked well.
Changes in V2:
- Replaced license header by SPDX-License-Identifier.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Donghwa Lee <dw09.lee@samsung.com>
[agust: sort Makefile entry alphabetically]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The cfb_console can't handle 4-bit wide font properly, since with
4-bit wide font, all 8 bits are drawn. Unbreak the video_drawchars()
function to correctly render 4-bits only on such fonts.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The LCDIF interface doesn't give us any means to do continuous refresh
when driving a SmartLCD. To work this around, we produce a special
circular DMA descriptor, which only writes the HW_LCDIF_CTRL0 register
and sets the RUN bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add hook that allow configuring SmartLCD attached the MXS LCDIF
controller operating in System-Mode. This hook can be overriden
by a platform-specific SmartLCD programming routine, which writes
the SmartLCD specific values into it's registers.
Also, this patch makes sure the SYNC signals are off for the
SmartLCD case.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Allocate the framebuffer aligned so it can be flushed
and the flush_dcache_range() function won't complain.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add special function that executes a specially crafted circular
DMA descriptor. The function doesn't wait for the descriptor to
finish the transfer, since the descritor never finishes. This is
useful when operating a SmartLCD through the LCDIF interface, as
the LCDIF does not give us any means to have continuous refresh
of the SmartLCD. Instead, the RUN bit in the LCDIF CTRL register
must be triggered manually. This can be worked around by starting
an DMA transfer which continuously sets the RUN bit. This function
allows starting exactly such transfer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
|\ \ |
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Some versions of the Zynq first stage boot loader enable PCAP loopback
during boot regardless of whether or not the boot image includes PL
configuration. This behavior only appears in certain boot modes (notably
QSPI boot). Attempting to configure the PL with the loopback bit set
will result in timeouts and will prevent successful configuration.
In order to avoid this problem, and to avoid dependency on the version
of the FSBL used to boot the system, ensure that the loopback enable bit
is cleared when loading the driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| | |
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
than 1sec, hence increased the program time by 4sec to
sync' all soc's.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| | |
Add support for SST25WF080 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Zynq spi controller driver supports 2 buses and
3 chipselects on each bus.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| | |
- CHECK: Alignment should match open parenthesis
- trailing whitespace
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| | |
- line over 80 characters.
- CHECK: Alignment should match open parenthesis
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
- line over 80 characters
- foo * bar -> foo *bar
- removed unnecessary for single statement blocks.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
- line over 80 characters
- add spaces
- add tabs
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| |
| |
| |
| |
| |
| |
| | |
- line over 80 characters
- insert the expression in same line
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
| |
| |
| |
| |
| |
| | |
Use DIV_ROUND_UP to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
|
|/
|
|
|
|
| |
Use DIV_ROUND_UP to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.
Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.
This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.
Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fixes NFS root problems with Beagle (3530 ES1.0) when used with
external USB-ethernet adapter and "USB start" command used within
u-boot.
Soft resetting the UHH module causes instability issues on
all OMAPs so we just avoid it.
See OMAP36xx Errata
i571: USB host EHCI may stall when entering smart-standby mode
i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
On OMAP4/5, soft-resetting the UHH module can put it into
Smart-Idle mode and lead to a deadlock.
On OMAP3 this doesn't seem to be the case but still instabilities
are observed on beagle (3530 ES1.0) if soft-reset is used.
e.g. NFS root failures with Linux kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
switch
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Implement functions to flush/invalidate dcache over QH and qTDs
and make use of them where appropriate. Also use them to replace
the old incorrect cache management attempt. This is the first step
towards making this driver work with data cache enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The code for retrieving qTD item for particular endpoint is hard
to understand, moreover it's duplicated all over the driver. Move
the code into single nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The code for retrieving QH for particular endpoint is hard to understand,
moreover it's duplicated all over the driver. Move the code into single
nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Check the length of system cacheline at compile-time and fail
if the system uses too long cachelines.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The endpoint QH list has to be aligned to 10-bit boundary. We also have
to make sure the list is aligned on a cacheline boundary. Make sure it
is. Furthermore, check if the memory allocation for the QH list didn't
fail. Moveover, improve the comment about the QH list structure.
Finally, the qTD item list has to be aligned only to 5-bit boundary, not
10-bit as it is now, fix this as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There is no need to init this field at runtime, so init it statically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The QH_MAXNUM is used in absolutelly incorrect manner and is not
even needed. Remove it and correctly replace it's occurance with
2 * NUM_ENDPOINTS .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Clean up the code that checks the validity of a USB gadget driver
in usb_gadget_register_driver(). Moreover, limit the speed of the
driver to either FULL or HIGH, this is more precise and once we
have xHCI support, also more correct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.
Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
|