summaryrefslogtreecommitdiff
path: root/drivers
Commit message (Collapse)AuthorAgeLines
* cs8900 compile fixLadislav Michl2009-03-29-1/+1
| | | | | | | | | | | cs8900.c: In function 'eth_init': cs8900.c:164: warning: passing argument 2 of 'eth_getenv_enetaddr' from incompatible pointer type cs8900.c:165: error: invalid operands to binary << cs8900.c:166: error: invalid operands to binary << cs8900.c:167: error: invalid operands to binary << Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Merge branch 'master' of git://git.denx.de/u-boot-at91Wolfgang Denk2009-03-26-2/+81
|\
| * at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.Nicolas Ferre2009-03-22-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * at91sam9/at91cap: move nand drivers to drivers/mtd/nandJean-Christophe PLAGNIOL-VILLARD2009-03-22-0/+79
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk2009-03-25-5/+3
|\ \
| * | Blackfin: spi: there is no PORTJ_FER MMR on BF537Sonic Zhang2009-03-23-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | Since the PORTJ on the BF537 is peripheral-only (no GPIO functionality), then there is no PORTJ_FER register for us to worry about. Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | | Add wait flags to support board/chip specific delaysWolfgang Grandegger2009-03-23-9/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The NAND flash on the TQM8548_BE modules requires a short delay after running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE requires a further short delay after writing out a buffer. Normally the R/B pin should be checked, but it's not connected on the TQM8548_BE. The corresponding Linux FSL UPM driver uses similar delay points at the same locations. To manage these extra delays in a more general way, I introduced the "wait_flags" field allowing the board-specific driver to specify various types of extra delay. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | | Add support for TQM-specific chip select logic to FSL-UPMWolfgang Grandegger2009-03-23-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | For the NAND chips on the TQM8548 modules, a special chip-select logic is used. It uses dedicated address lines to be set via UPM machine address register (mar). This patch adds such support to the FSL-UPM driver. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | | Add multi chip support to the FSL-UPM driverWolfgang Grandegger2009-03-23-8/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for multi-chip NAND devices to the FSL-UPM driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now called with the argument "chip_nr" to allow testing the proper chip select line. The NAND support of the MPC8360ERDK is updated as well. No other boards are currently using the FSL UPM driver. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | | Enable multi chip support in the NAND layerWolfgang Grandegger2009-03-23-1/+7
|/ / | | | | | | | | | | | | | | | | | | This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer. Multi-chips devices are displayed as shown: Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | Make flash protection work, when the environment is in EEPROMEric Schumann2009-03-23-1/+3
|/ | | | | | | | | | | | | | | | On the pcm030 the environment is located in the onboard EEPROM. But we want to handle flash sector protection in a safe manner. So we must read the unlock environment variable from EEPROM instead from flash. This patch is required as long the evironment is saved into the EEPROM. Stefan: Additional change as suggested by Wolfgang, use bigger char array (instead of 4). Signed-off-by: Eric Schumann <E.Schumann@phytec.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'next' of ../nextWolfgang Denk2009-03-21-278/+131
|\
| * Move ali512x.hGraeme Russ2009-03-20-1/+1
| | | | | | | | | | | | Moved ali512x.h from include/asm-i386/ic/ to /include Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
| * lan91c96/smc91111/smc911x: get mac address from environmentMike Frysinger2009-03-20-132/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The environment is the canonical storage location of the mac address, so we're killing off the global data location and moving everything to querying the env directly. Also, do not bother checking the EEPROM if the env is setup. This simplifies the code greatly. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Wolfgang Dnek <wd@denx.de> CC: Ben Warren <biggerbadderben@gmail.com> CC: Rolf Offermanns <rof@sysgo.de> CC: Erik Stahlman <erik@vt.edu> CC: Daris A Nevil <dnevil@snmc.com> CC: Sascha Hauer <s.hauer@pengutronix.de>
| * sh_eth: get mac address from environmentMike Frysinger2009-03-20-22/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The environment is the canonical storage location of the mac address, so we're killing off the global data location and moving everything to querying the env directly. The sh_eth driver can also be simplified a bit by using enetaddr member of the eth_device structure. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Carlos Munoz <carlos@kenati.com> CC: Ben Warren <biggerbadderben@gmail.com>
| * cs8900: get mac address from environmentMike Frysinger2009-03-20-40/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | The environment is the canonical storage location of the mac address, so we're killing off the global data location and moving everything to querying the env directly. The cs8900 driver also changes slightly in that the hardware is not consulted if the mac address in the env is sane. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Marius Groeger <mgroeger@sysgo.de> CC: Ben Warren <biggerbadderben@gmail.com>
| * bcm570x: get mac address from environmentMike Frysinger2009-03-20-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The environment is the canonical storage location of the mac address, so we're killing off the global data location and moving everything to querying the env directly. Since the address is in the PLM_DEVICE_BLOCK structure already, there is no need to pass the NodeAddress as a second parameter. So drop the second argument to the LM_SetMacAddress() function (and update the tigon3 driver accordingly). Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Ben Warren <biggerbadderben@gmail.com>
| * drivers/net/: get mac address from environmentMike Frysinger2009-03-20-68/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The environment is the canonical storage location of the mac address, so we're killing off the global data location and moving everything to querying the env directly. The drivers that get converted here: 3c589 4xx_enet dc2114x dm9000x enc28j60 fsl_mcdmafec ks8695eth mcffec rtl8019 rtl8169 s3c4510b_eth xilinx_emac xilinx_emaclite Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Ben Warren <biggerbadderben@gmail.com> CC: Rolf Offermanns <rof@sysgo.de> CC: Stefan Roese <sr@denx.de> CC: Sascha Hauer <saschahauer@web.de> CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com> CC: Greg Ungerer <greg.ungerer@opengear.com> CC: Xue Ligong <lgxue@hotmail.com> CC: Masami Komiya <mkomiya@sonare.it> CC: Curt Brune <curt@cucy.com> CC: Michal SIMEK <monstr@monstr.eu>
| * Blackfin: bfin_mac: force boards to setup the MAC themselvesMike Frysinger2009-03-20-9/+9
| | | | | | | | | | | | | | | | | | Since the on-chip MAC does not have an eeprom or similar interface, force all Blackfin boards that use this driver to setup the board data with a proper MAC. Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Ben Warren <biggerbadderben@gmail.com>
* | Replaced endpoint numbers with appropriate macros in usbtty.c.Vivek Kutal2009-03-21-6/+6
|/ | | | | Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* net: sh_eth: Remove sh_eth_reset() from halt functionNobuhiro Iwamatsu2009-03-20-2/+0
| | | | | | | | | sh_eth_reset is function to reset Ether IP. The MAC address is stored in IP, but it is initialized by this function. OS (e.g. Linux Kernel) can not use this device when initialized. This revises this problem. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
* CFI: geometry reversal for STMicro M29W320DTRichard Retanubun2009-03-19-2/+3
| | | | | | | | Follow up to the flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip. The M29W320DT has 4 erase region. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Stefan Roese <sr@denx.de>
* 8xx: add support for new keymile kmsupx4 board.Heiko Schocher2009-03-18-1/+1
| | | | | | | | | | | | | This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: Heiko Schocher <hs@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk2009-03-15-3/+13
|\
| * sh: Add some register value configurable to PCI of SH7780Yoshihiro Shimoda2009-03-12-3/+3
| | | | | | | | | | | | | | | | Some register value was hardcoded for System memory size 128MB and memory offset 0x08000000. This patch fixed the problem. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * sh: Add system memory registration to PCI for SH4Yoshihiro Shimoda2009-03-12-0/+10
| | | | | | | | | | | | | | It is necessary for some pci device driver. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | MPC5200 FEC MII speed registerJon Smirl2009-03-13-7/+16
|/ | | | | | Set a non-zero speed in the MII register so that MII commands will work. Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
* tsec: report when there is no vendor specific PHY supportPaul Gortmaker2009-03-09-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | Commit af1c2b84 added a generic phy support, with an ID of zero and a 32 bit mask; meaning that it will match on any PHY ID. The problem is that there is a test that checked if a matching PHY was found, and if not, it printed the non-matching ID. But since there will always be a match (on the generic PHY, worst case), this test will never trip. In the case of a misconfigured PHY address, or of a PHY that isn't explicitly supported outside of the generic support, you will never see the ID of 0xffffffff, or the ID of the real (but unsupported) chip. It will silently fall through onto the generic support. This change makes that test useful again, and ensures that the selection of generic PHY support doesn't happen without some sort of notice. It also makes it explicitly clear that the generic PHY must be last in the PHY table. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Andy Fleming <afleming@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2009-03-09-1/+21
|\ | | | | | | | | | | | | Conflicts: lib_ppc/board.c Signed-off-by: Wolfgang Denk <wd@denx.de>
| * 83xx, i2c: add mux support for fsl_i2cHeiko Schocher2009-03-05-1/+21
| | | | | | | | | | | | | | | | | | | | This patch adds I2C mux support for the fsl_i2c driver. This allows you to add "new" i2c busses, which are reached over i2c muxes. For more infos, please look in the README and search for CONFIG_I2C_MUX. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | smc911x: split out useful defines/functions into local headerMike Frysinger2009-02-25-455/+496
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The smc911x driver has a lot of useful defines/functions which can be used by pieces of code (such as example eeprom programmers). Rather than forcing each place to duplicate these defines/functions, split them out of the smdc911x driver into a local header. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Ben Warren <biggerbadderben@gmail.com> CC: Sascha Hauer <s.hauer@pengutronix.de> CC: Guennadi Liakhovetski <lg@denx.de> CC: Magnus Lilja <lilja.magnus@gmail.com> CC: Ben Warren <biggerbadderben@gmail.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk2009-02-24-19/+1084
|\ \
| * | video: add an i.MX31 framebuffer driverGuennadi Liakhovetski2009-02-24-0/+857
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add a driver for the Synchronous Display Controller and the Display Interface on i.MX31, using IPU for DMA channel setup. So far only displaying of bitmaps is supported, no text output. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
| * | A driver for the S6E63D6 SPI display controller from SamsungGuennadi Liakhovetski2009-02-24-0/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | This is a driver for the S6E63D6 SPI OLED display controller from Samsung. It only provides access to controller's registers so the client can freely configure it. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
| * | i.MX31: support GPIO as a chip-select in the mxc_spi driverGuennadi Liakhovetski2009-02-24-8/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | Some SPI devices have special requirements on chip-select handling. With this patch we can use a GPIO as a chip-select and strictly follow the SPI_XFER_BEGIN and SPI_XFER_END flags. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * | i.MX31: add a simple gpio driverGuennadi Liakhovetski2009-02-24-1/+75
| | | | | | | | | | | | | | | | | | | | | | | | This is a minimal driver, so far only managing output. It will be used by the mxc_spi.c driver. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * | i.MX31: fix SPI driver for shorter than 32 bitGuennadi Liakhovetski2009-02-24-11/+20
| | | | | | | | | | | | | | | | | | | | | | | | Fix setting the SPI Control register, 8 and 16-bit transfers and a wrong pointer in the free routine in the mxc_spi driver. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2009-02-24-0/+13
|\ \ \ | |/ / |/| / | |/
| * PCI: Add pci_last_busno() helperAnton Vorontsov2009-02-23-0/+13
| | | | | | | | | | | | | | | | | | | | This is just a handy routine that reports last PCI busno: we walk down all the hoses and return last hose's last_busno. Will be used by PCI/PCIe initialization code. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Added Vitesse VSC8211 definitions to TSEC driverPieter Henning2009-02-22-0/+30
|/ | | | | | | | Added the struct containing PHY settings for the Vitesse VSC8211 phy to the phy_info list in tsec.c Signed-off-by: Pieter Henning <phenning@vastech.co.za> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-02-22-67/+519
|\
| * OMAP3: Clean up MMC codeDirk Behme2009-02-22-67/+70
| | | | | | | | | | | | | | | | | | | | Clean up OMAP3 MMC code: * Convert register access to struct & readx/writex style * Replace hardcode values by macros * Remove macro defined twice Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
| * nomadik/nand: fix 'ecc512' discards qualifiers from pointer target typeJean-Christophe PLAGNIOL-VILLARD2009-02-22-1/+1
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * arm: add uart dcc supportJean-Christophe PLAGNIOL-VILLARD2009-02-22-0/+227
| | | | | | | | | | | | | | | | | | | | Serial driver via the EmbeddedICE macrocell's DCC channel using co-processor 14. It does include a timeout to ensure that the system does not totally freeze when there is nothing connected to read. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * Nand driver for Nomadik SoCAlessandro Rubini2009-02-22-0/+222
| | | | | | | | | | | | | | | | | | | | This driver implements the ECC algorithm described in the CPU data sheet and uses the OOB layout chosen in already-released development systems (shipped with a custom-made u-boot 1.3.1). Signed-off-by: Alessandro Rubini <rubini@unipv.it> Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
* | r8a66597-hcd: fix cannot use external hubYoshihiro Shimoda2009-02-22-5/+31
|/ | | | | | | | Fix the problem that cannot use external hub, because this driver did not control correctly a DEVADDx register. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* Coding Style cleanup; update CHANGELOGWolfgang Denk2009-02-22-2/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* fpga: Fix Spartan III FPGA bootingMatthias Fuchs2009-02-21-15/+7
| | | | | | | | | | | | This patch does some minor fixing of the Xilinx Spartan III FPGA boot code: - Fixed call order of post configuration callback and success message printing (result of copy-paste?) - remove obsolete comment - minor coding style cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
* fpga: Fix Spartan II FPGA bootingMatthias Fuchs2009-02-21-21/+11
| | | | | | | | | | | | | | This patch does some minor fixing of the Xilinx Spartan II FPGA boot code: - Fixed call order of post configuration callback and success message printing (result of copy-paste?) - relocate post configuration callback only when it is implemented - remove obsolete comment - minor coding style cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
* drivers/serial/ns16550: move ifdef into Makefile COBJS-$(...)Mike Frysinger2009-02-21-11/+3
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit v1.1 at 2024-12-01 02:35:49 +0000