summaryrefslogtreecommitdiff
path: root/drivers
Commit message (Collapse)AuthorAgeLines
* ehci-omap: Clean up added ehci-omap.cGovindraj.R2012-02-12-55/+154
| | | | | | | | | | | | | | | | | | Clean up added ehci-omap.c and make it generic for re-use across omap-soc having same ehci ip block. Also pass the modes to be configured from board file and configure the ports accordingly. All usb layers are not cache aligned, till then keep cache off for usb ops as ehci will use internally dma for all usb ops. * Add a generic common header ehci-omap.h having common ip block data and reg shifts. * Rename and modify ehci-omap3 to ehci.h retain only conflicting sysc reg shifts remove others and move to common header file. * pass the board data for beagle/panda accordinly to use ehci ports. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* ehci-omap: driver for EHCI host on OMAP3Ilya Yanok2012-02-12-0/+157
| | | | | | | Taken from Beagle code. Tested on mcx board (AM3517-based). Signed-off-by: Ilya Yanok <yanok@emcraft.com> Tested-by: Stefano Babic <sbabic@denx.de>
* usb: ulpi: Add omap-ulpi-view port supportGovindraj.R2012-02-12-0/+106
| | | | | | | | | | | | | | | | | | | Based on discussion from this thread [1]. Adding omap-view port that helps us in using the generic ulpi framework for any ulpi phy ops using the INSNREG05_ULPI viewport reg available on omap platform. Currently ehci ports are available on omap3/4 platforms so enable the same for beagle and panda, patch is tested on the same boards. Thanks to Igor Grinberg <grinberg@compulab.co.il> for reviewing the omap-ehci patches and suggesting this approach. [1]: http://www.mail-archive.com/u-boot@lists.denx.de/msg76076.html Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* usb: ulpi: Extend the existing ulpi framework.Govindraj.R2012-02-12-41/+45
| | | | | | | | | | Extend the existing ulpi viewport framework to pass the port number information for any ulpi ops. Fix the usage of ulpi api's accordingly. Tested-by: Stefano Babic <sbabic@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* orion5x: add USB host ehci-marvell supportAlbert ARIBAUD2012-02-12-0/+5
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Remove kirkwood-specifics from marvell EHCI driverAlbert ARIBAUD2012-02-12-14/+17
| | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Rename ehci-kirkwood as ehci-marvellAlbert ARIBAUD2012-02-12-1/+1
| | | | | Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* kirkwood_spi: correct access to irq_mask registerIan Campbell2012-02-12-1/+1
| | | | | | | | | | | | Problem appears to have been present since day one but masked because alignment aborts were not enabled. ca4b55800ed7 "arm, arm926ejs: always do cpu critical inits" turned on alignment aborts and uncovered this latent problem. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-By: Jason Cooper <u-boot@lakedaemon.net> Tested-By: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* mx28: fix i.MX28 spi driverMatthias Fuchs2012-02-12-3/+9
| | | | | | | | | | | | | | | The generic spi flash driver (drivers/mtd/spi/spi_flash.c) uses the spi low level driver's spi_xfer() function with len=0 to deassert the SPI flash' chip select. But the i.MX28 spi driver rejects this call due to len=0. This patch implements an exception for len=0 with the SPI_XFER_END flag set. This results in an extra read with the chip select being deasserted afterwards. There seems to be no way to deassert the signal by hand. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* mmc: access mxcmmc from mx31 boardsHelmut Raiger2012-02-12-5/+3
| | | | | | | | | | | | | | | | | This patch modifies mxcmmc.c to be used not only by i.MX27 but also by i.MX31 boards. Both use the same SD controller, but have different clock set-ups. The i.MX27 imx_get_XXXclock functions are made static to generic.c and a public mxc_get_clock() function is provided. Pins, base address and prototypes for an i.MX31 specific board_init_mmc() are provided. Some of the i.MX27 clock getters are unused and marked as such to avoid warnings (./MAKEALL -s mx27), but the code was left in for future use. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
* tegra: mmc: Support operation with dcache enabledSimon Glass2012-02-12-0/+16
| | | | | | | | | | | When the data cache is enabled we must flush on write and invalidate on read. We also check that buffers are aligned to data cache lines boundaries. With recent work in U-Boot this should generally be the case but the warnings will catch problems. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk2012-02-11-0/+23
|\ | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-cfi-flash: add STM29F400BB to table of supported legacy flashs * Fix: watchdog timed out, if flash blank (0xFF) blocks
| * add STM29F400BB to table of supported legacy flashsDavid Müller (ELSOFT AG)2012-02-09-0/+20
| | | | | | | | | | Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
| * * Fix: watchdog timed out, if flash blank (0xFF) blocksJens Scharsig (BuS Elektronik)2012-02-09-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current implementation of cfi_flash uses udelay to reset watchdog. If several blocks are blank (0xff filled) the watchdog timed out. The reason is, udelay is never called, if flash device is ready to fast. e.g. mw.w $(copy_addr) FFFF 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog timed out mw.w $(copy_addr) 0000 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog not timed out This patch adds an extra watchdog reset in front of flash ready check. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk2012-02-11-401/+1175
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-nand-flash: nand/fsl_elbc: Convert to self-init nand: Introduce CONFIG_SYS_NAND_SELF_INIT nand_spl: store ecc data on the stack mtd/nand: Add ONFI support for FSL NAND controller nand: make 1-bit software ECC configurable nand: Sanitize ONFI strings. nand: Merge changes to BBT from Linux nand driver nand: Merge changes from Linux nand driver nand: cleanup whitespace nand: Add more NAND types from Linux nand driver nand: Merge BCH code from Linux nand driver NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS NAND: remove NAND_MAX_CHIPS definitions nand_spl_simple: store ecc data on the stack
| * | nand/fsl_elbc: Convert to self-initScott Wood2012-01-26-5/+38
| | | | | | | | | | | | | | | | | | | | | | | | This driver doesn't yet make use of the added flexibility (not that that should stop anyone from converting...), but it will with the in-progress hack to support 4k-page NAND. Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: Introduce CONFIG_SYS_NAND_SELF_INITScott Wood2012-01-26-37/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows a driver to run code between nand_scan_ident() and nand_scan_tail(), among other things. See the additions to doc/README.nand for details. To allow a gradual transition, Boards that don't set CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but new drivers should not require this, and existing drivers should be converted when convenient. Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | mtd/nand: Add ONFI support for FSL NAND controllerShengzhou Liu2012-01-26-7/+10
| | | | | | | | | | | | | | | | | | | | | | | | - fix NAND_CMD_READID command for ONFI detect. - add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: make 1-bit software ECC configurableChristian Hitz2012-01-26-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The software ECC algorithm is not necessary when hardware ECC is available and can be left out for a smaller image size. Enable with CONFIG_MTD_ECC_SOFT. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: Sanitize ONFI strings.Christian Hitz2012-01-26-1/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This is part of the synchronization with the nand driver to the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: Merge changes to BBT from Linux nand driverChristian Hitz2012-01-26-99/+328
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: Merge changes from Linux nand driverChristian Hitz2012-01-26-150/+309
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> [scottwood@freescale.com: minor fixes] Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: cleanup whitespaceChristian Hitz2012-01-26-74/+78
| | | | | | | | | | | | | | | | | | | | | | | | Bring up to date with corresponding file from linux. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: Add more NAND types from Linux nand driverChristian Hitz2012-01-26-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch merges the additional NAND flash types from the 3.0 Linux kernel. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand: Merge BCH code from Linux nand driverChristian Hitz2012-01-26-1/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch merges the BCH ECC algorithm from the 3.0 Linux kernel. This enables U-Boot to support modern NAND flash chips that require more than 1-bit of ECC in software. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | nand_spl_simple: store ecc data on the stackStefano Babic2012-01-26-26/+16
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM which is likely to contain already loaded data. The patch saves the oob data and the ecc on the stack replacing the fixed address in RAM. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | ARM: AM33XX: Add AM33XX I2C driver supportPatil, Rachna2012-01-23-7/+13
| | | | | | | | | | | | | | | | 1. Compliant with Philips I2C specification version 2.1 2. Supports upto 100Kbps in standard mode Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
* | ARM: I2C: I2C Multi byte address supportPatil, Rachna2012-01-23-173/+296
|/ | | | | | | | | | Existing OMAP I2C driver does not support address length greater than one. Hence this patch is to add support for 2 byte address read/write. Signed-off-by: Philip, Avinash <avinashphilip@ti.com> Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Signed-off-by: Patil, Rachna <rachna@ti.com>
* drivers/i2c/omap24xx_i2c.c: move all local variables to SRAMAndreas Müller2012-01-16-4/+9
| | | | | | | | | | | | | At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately this pin is also used for revision detection. Therefore we need to send shut-up to TWL4030 to avoid reading wrong revision. In SPL this must be done before SDRAM is set up because the type of SDRAM is revision dependent. By this patch it is ensured that all variables used by omap24xx_i2c.c are located in SRAM. Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* drivers/i2c/omap24xx_i2c.c: replace printf with one argument by putsAndreas Müller2012-01-16-6/+6
| | | | | Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de>
* net: imx: Add multi-FEC support for imx_get_mac_from_fuseFabio Estevam2012-01-16-5/+6
| | | | | | | | | | Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter. This feature is important on mx28 SoC for example that has two FEC ports. Cc: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* fec: add the i.mx6q enet driver supportJason Liu2012-01-16-1/+16
| | | | | | Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Jason Liu <jason.hui@linaro.org> Acked-by: Stefano Babic <sbabic@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2012-01-13-218/+429
|\ | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mpc83xx: mpc8313erdb: fix mtdparts address powerpc/83xx/km: add support for 8321 based tuge1 board powerpc/83xx/km: merge tuxa and tuda1 boards to tuxx1 powerpc/83xx/km: remove obsolete defines for tuda1 powerpc/83xx/km: update SDRAM parameters for km8321 boards mpc8313erdb: Enable GPIO support on the MPC8313E RDB mpc83xx: Add a GPIO driver for the MPC83XX family gpio: Replace ARM gpio.h with the common API in include/asm-generic gpio: Modify common gpio.h to more closely match Linux
| * mpc83xx: Add a GPIO driver for the MPC83XX familyJoe Hershberger2012-01-09-0/+200
| | | | | | | | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * gpio: Replace ARM gpio.h with the common API in include/asm-genericJoe Hershberger2012-01-09-218/+229
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ARM boards should use the generic GPIO API This means changing gpio to unsigned type Remove the unused gpio_toggle() function which is not part of the API Comment that free should not modify pin state Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> fixed merge conflict in da8xx_gpio.c, tegra2_gpio.c, and extended to the new mxs_gpio.c. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | fsl_esdhc: fix PIO mode transfersIra Snyder2012-01-08-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The pointer to the registers used to control the Freescale ESDHC MMC controller is not initialized correctly when using PIO mode. This is fixed by initializing the pointer in the same way as all other sites within the driver. Examining the commit history shows that this was broken at introduction due to a code change in upstream U-Boot to support the mx51 processor family. Reported-by: Jim Lentz <JLentz@zhone.com> Cc: Andy Fleming <afleming@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
* | mmc: tegra2: Implement card-detect hook.Thierry Reding2012-01-08-19/+13
| | | | | | | | | | | | | | | | | | | | On Tegra2, card-detection is implemented by passing the card-detection GPIOs to the MMC driver at initialization time. Instead of implementing the board_mmc_getcd() function, use the card-detect hook and allow boards to override it by providing their own board_mmc_getcd() implementation. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
* | mmc: fsl_esdhc: Implement card-detect hook.Thierry Reding2012-01-08-17/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This card-detect hook probably doesn't work. Perhaps somebody with more knowledge about the hardware can comment on this. I think that perhaps even the complete code from esdhc_init() could go into the getcd() function instead or mmc_getcd() needs to be called at some later time after mmc_init(), which, however, would require many other drivers to change. In addition to implementing the hook, this patch also removes the call to the board_mmc_getcd() function which is now called from the MMC framework and is no longer required here. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
* | mmc: Implement card detection.Thierry Reding2012-01-08-0/+31
| | | | | | | | | | | | | | | | | | | | | | Check for card detect each time an MMC/SD device is initialized. If card detection is not implemented, this code behaves as before and continues assuming a card is present. If no card is detected, has_init is reset for the MMC/SD device (to force initialization next time) and an error is returned. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
* | mmc: Change board_mmc_getcd() function prototype.Thierry Reding2012-01-08-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The new API no longer uses the extra cd parameter that was used to store the card presence state. Instead, this information is returned via the function's return value. board_mmc_getcd() returns -1 to indicate that no card-detection mechanism is implemented; 0 indicates that no card is present and 1 is returned if it was detected that a card is present. The rationale for this change can be found in the following email thread: http://lists.denx.de/pipermail/u-boot/2011-November/110180.html In summary, the old API was not consistent with the rest of the MMC API which always passes a struct mmc as the first parameter. Furthermore the cd parameter was used to mean "card absence" in some implementations and "card presence" in others. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
* | drivers/mmc/mv_sdhci.c: Fix build warningAnatolij Gustschin2012-01-08-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Fix: mv_sdhci.c: In function 'mv_sdh_init': mv_sdhci.c:47:22: warning: the comparison will always evaluate as 'true' for the address of 'mv_sdhci_writeb' will never be NULL [-Waddress] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Lei Wen <leiwen@marvell.com> Cc: Andy Fleming <afleming@freescale.com> Acked-by: Lei Wen <leiwen@marvell.com>
* | ftsdc010: improve performance and capabilityMacpaul Lin2012-01-08-85/+103
| | | | | | | | | | | | | | | | | | | | This patch improve the performance by spliting flag examination code in ftsdc010_send_cmd() into 3 functions. This patch also reordered the function which made better capability to some high performance cards against to the next version of ftsdc010 hardware. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* | mmc: add host_caps checking avoid switch card improperlyMacpaul Lin2012-01-08-0/+10
| | | | | | | | | | | | | | | | | | | | | | Add a host capability checking to avoid the mmc stack switch the card to HIGHSPEED mode when the card supports HIGHSPEED while the host doesn't. This patch avoid furthur transaction problem when the mmc/sd card runs different mode to the host. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* | i.mx: fsl_esdhc: add the i.mx6q supportJason Liu2012-01-08-3/+9
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mmc host controller on the i.mx6q is called usdhc which is redesigned based on the freescale esdhc controller. The usdhc controller is almost compatible with esdhc except it adds one mix register to support debug/SD3.0 and move the low bit 0-6 of XFERTYP register to the mix control reg low bit 0-6. Thus on i.mx6q, we have the following compared with the previous soc: (can refer to RM of chapter 56.3.3) i.mx6q: mix control: bit 31 - bit 7: Added for debug/SD3.0 support bit 6 - bit 0: move in the XFERTYP register bit 6-0 on previous soc XFERTYP register: bit 31 - bit 7: the same as before, bit 6 - bit 0: no-use previous soc mix control: no XFERTYP register: bit 31 - bit 0: xfertype information Signed-off-by: Jason Liu <jason.hui@linaro.org> Cc: Andy Fleming <afleming@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* net: add Calxeda xgmac driverRob Herring2012-01-05-0/+554
| | | | | | | | | | This adds ethernet driver for Calxeda xgmac found on Highbank SOC. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Fix: WARNING: __aligned(size) is preferred over __attribute__((aligned(size))) Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2012-01-05-2/+342
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: tegra2: Optimize out-of-tree build for Ventana. tegra: Move boards over to use arch-level board UART function tegra: Add support for UART init in cpu board.c tegra: Add a function mux feature tegra: add clock_ll_start_uart() to enable UART prior to reloc tegra: Move clock_early_init() to arch_cpu_init() tegra: Move cpu_init_cp15() to arch_cpu_init() arm: Tegra: Fix Harmony and Ventana builds in u-boot-tegra/master tegra: Fix build error in plutux, medcom tegra2: Add Avionic Design Medcom support. tegra2: Add Avionic Design Plutux support. tegra2: Add common Avionic Design Tamonten support. tegra2: Move tegra2_mmc_init() prototype to public header. tegra2: Change CONFIG_SYS_TEXT_BASE to 0x00108000. tegra2: Always build with USE_PRIVATE_LIBGCC=yes. tegra2: Plumb in SPI/UART switch code tegra2: spi: Support SPI / UART switch tegra2: Implement SPI / UART GPIO switch tegra2: Enable SPI environment on Seaboard tegra2: config: Enable SPI flash on Seaboard tegra2: spi: Add SPI driver for Tegra2 SOC tegra2: Add UARTB support tegra2: Tidy UART selection arm, davinci: Fix build warnings for cam_enc_4xx Devkit8000: Switch over to enable_gpmc_cs_config arm, davinci: Add support for generating AIS images to the Makefile mkimage: Fix variable length header support arm, da850evm: Add an SPL for SPI boot arm, davinci: Add SPL support for DA850 SoCs sf: Add spi_boot() to allow booting from SPI flash in an SPL spl: display_options.o is required for SPI flash support in SPL ARM: omap3: add support to Technexion twister board ARM: omap3: added common configuration for Technexion TAM3517 vision2: Fix checkpatch warning
| * tegra2: Move tegra2_mmc_init() prototype to public header.Thierry Reding2011-12-24-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | tegra2_mmc_init() is implemented by the Tegra2 MMC driver. Since most of the Tegra2-based boards will need to call it, this commit exports it in the new public asm/arch/mmc.h header file to prevent each board from providing its own prototype. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra2: spi: Support SPI / UART switchSimon Glass2011-12-24-0/+14
| | | | | | | | | | | | | | | | | | | | Add the SPI / UART switch logic into the Tegra2 SPI driver so that it can co-exist with the NS16550 UART. We need the ns16550.h header for NS16550_t for now. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra2: spi: Add SPI driver for Tegra2 SOCTom Warren2011-12-24-0/+266
| | | | | | | | | | | | | | This driver supports SPI on Tegra2, running at 48MHz. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
| * sf: Add spi_boot() to allow booting from SPI flash in an SPLChristian Riesch2011-12-24-0/+62
| | | | | | | | | | | | | | | | Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Heiko Schocher <hs@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
generated by cgit v1.1 at 2024-11-06 01:34:51 +0000