summaryrefslogtreecommitdiff
path: root/drivers/usb
Commit message (Collapse)AuthorAgeLines
...
* | usb:gadget:ums: Replace malloc calls with memalign to fix cache buffer alignmentLukasz Majewski2014-02-06-2/+2
|/ | | | | | | | Calls to malloc() have been replaced by memalign. It now provides proper buffer alignment. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb: exynos5: arndale: Add network supportInderpal Singh2014-01-13-0/+2
| | | | | | | | | | | | Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo controller, connected to HSIC Phy of USB host controller via USB3503 hub. This patch uses board specific board_usb_init function to perform reset sequence for USB3503 hub and enables the relevant config options for network to work. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
* usb: ehci: exynos: set/reset hsic physInderpal Singh2014-01-13-0/+39
| | | | | | | | The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2 are for HSIC phys. The usb 2.0 phy is already being setup. This patch sets up the hsic phys. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
* usb: gadget: fotg210: EP0 fifo empty indication is non-reliableKuo-Jung Su2014-01-13-0/+1
| | | | | | | | | | | | | | | | | | The fifo size of ep0 is 64 bytes, and if the packet size grater than 64 bytes, the driver would have to fill up the fifo multiple times, and before filling up the fifo, the driver should make sure the fifo is empty by checking fifo empty indication. However there is a hardware bug that the fifo empty indication is somehow a bit earlier than fifo reset. So if I don't add an extra delay here, the data might be corrupted. (i.e., 1 byte missing) After a couple of tests, it truns out that 1 usec is good enough. This workaround should be applied to all hardware revisions. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Marek Vasut <marex@denx.de>
* usb: gadget: fotg210: add w1c interrupt status supportKuo-Jung Su2014-01-13-0/+14
| | | | | | | | | | | | | | Since hardware revision 1.11.0, the following interrupt status registers are now W1C (i.e., write 1 clear): 1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5) 2. Interrupt Source Group 2 Register (0x14C) (All bits) And before revision 1.11.0, these registers are all R/W. Which means software must write a 0 to clear the status. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Marek Vasut <marex@denx.de>
* usb: ehci: Fix register accessMarek Vasut2013-12-18-1/+1
| | | | | | | | Fix the register access in EHCI HCD. We need to use address of the register as an ehci_writel() argument. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
* usb: ehci: Do not de-init uninited controllersMarek Vasut2013-12-18-0/+3
| | | | | | | | | In case the controller is not initialized, we shall not de-initialize it. As the control structure will not be filled, we will produce a null ptr dereference if the controller is not inited. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
* usb: ehci-pci: Clarify and cleanup the EHCI controller detectionMarek Vasut2013-12-18-3/+25
| | | | | | | | | The detection function of the EHCI PCI controller was really cryptic, add a beefy comment and clean the portion of the code up a bit. No change in the logic of the code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Glass <sjg@chromium.org>
* usb: f_dfu: cosmetic: Code cleanupLukasz Majewski2013-12-18-2/+2
| | | | | | Code cleanup for dfu_bind_config function Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* usb: dfu: f_dfu: Provide infrastructure to adjust DFU's Poll Timeout valueLukasz Majewski2013-12-18-3/+38
| | | | | | | | | | | It is necessary to deter the host from sending subsequent DFU_GETSTATUS request in the case of e.g. writing the buffer to medium. Here the timeout is increased when we fill up the whole buffer. This delay allows eMMC memory to perform its internal operations. Otherwise we end up with HOST's error regarding GET_STATUS receive timeout. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* drivers/usb/gadget: select objects by obj-$(CONFIG-...)Masahiro Yamada2013-12-13-6/+2
| | | | | | | | | | | | Before switching to the real Kbuild, drivers/usb/gadget/Makefile must be fixed. If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE is defined, both obj- and obj-y get empty. We need non-empty obj- or obj-y on each Makefile to generate built-in.o on the real Kbuild. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-12-06-2/+12
|\
| * driver:usb:s3c_udc: add support for Exynos4x12Piotr Wilczek2013-12-02-2/+12
| | | | | | | | | | | | | | | | This patch add new defines for usb phy for Exynos4x12. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | usb: ehci-omap: Reset the USB Host OMAP moduleRoger Quadros2013-12-06-15/+42
|/ | | | | | | | | | | | | | | | | | | In commit bb1f327 we removed the UHH reset to fix NFS root (over usb ethernet) problems with Beagleboard (3530 ES1.0). However, this seems to cause USB detection problems for Pandaboard, about (3/8). On further investigation, it seems that doing the UHH reset is not the cause of the original Beagleboard problem, but in the way the reset was done. This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based on the UHH_REVISION register. This should fix the Beagleboard NFS problem as well as the Pandaboard USB detection problem. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> CC: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Roger Quadros <rogerq@ti.com>
* usb, g_dnl: make bcdDevice value configurableHeiko Schocher2013-11-12-4/+19
| | | | | | | | | | | add the possibility to set the bcdDevice number board specific. Therefore the weak function g_dnl_get_board_bcd_device_number() is introduced. Used on the siemens boards. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-09-9/+10
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * arm: atmel: get rid of too many ifdefferyBo Shen2013-11-04-10/+4
| | | | | | | | | | | | | | | | | | | | | | Get rid of too many ifdeffery in usb ohci driver Add following two configuration for USB clock selecting - CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock - CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * arm: atmel: at91sam9n12ek: add usb host supportBo Shen2013-11-04-2/+9
| | | | | | | | | | | | | | Add usb host support for at91sam9n12ek board. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* | usb, g_dnl: make iSerialNumber board configurableHeiko Schocher2013-11-08-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | add the possibility to set the iSerialNumber board specific. Default value for iSerialNumber is 0x0. This value can changed board specific through the new function g_dnl_set_serialnumber() which must be called from the board specific function g_dnl_bind_fixup(). Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
* | usb: ohci-hcd: submit_common_msg: report actual_length properlyMateusz Kulikowski2013-11-08-1/+1
| | | | | | | | | | | | | | submit_common_msg should report amount of data passed from/to device. Instead, it always returned size requested by Host. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
* | usb: ums: add ums exit feature by ctrl+c or by detach usb cablePrzemyslaw Marczak2013-11-08-3/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch allows exiting from UMS mode to u-boot prompt by detaching usb cable or by pressing ctrl+c. Add new config: CONFIG_USB_CABLE_CHECK. If defined then board file should provide function: usb_cable_connected() (include/usb.h) that return 1 if cable is connected and 0 otherwise. Changes v2: - add a note to the README Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
* | usb: ums: fix disk capacity miscalculation and code cleanupPrzemyslaw Marczak2013-11-08-23/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch prevents: - ums disk capacity miscalculation because of integer overflow Changes v2: - Prevents passing zero size disk capacity to ums gadget driver - Change function ums_get_capacity() to ums_disk_init() and do ums disk initialization before gadget init - Remove unnecessary code from mass storage driver Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
* | usb: ums: code refactoring to improve reusability on other boards.Przemyslaw Marczak2013-11-08-23/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces some cleanups to ums code. Changes: ums common: - introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in usb_mass_storage.h both default values as 0 if board config doesn't define them common cleanup changes: - change name of struct "ums_board_info" to "ums" - "ums_device" fields are moved to struct ums and "dev_num" is removed - change function name: board_ums_init to ums_init - remove "extern" prefixes from usb_mass_storage.h cmd_usb_mass_storage: - change error() to printf() if need to print info message - change return values to command_ret_t type at ums command code - add command usage string Changes v2: ums common: - always returns number of read/write sectors - coding style clean-up ums gadget: - calculate amount of read/write from device returned value. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com>
* | drivers: usb: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-224/+69
| | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | powerpc/usb:Differentiate USB controller base addressramneek mehresh2013-10-24-4/+15
| | | | | | | | | | | | | | | | Introduce different macros for storing addresses of multiple USB controllers. This is required for successful initialization and usage of multiple USB controllers inside u-boot Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* | usb: rename board_usb_init_type to usb_init_typeTroy Kisky2013-10-22-2/+2
| | | | | | | | | | | | | | | | | | commit bba679144d25b91bcd7befff5a96728a30875f54 "usb: rename board_usb_init_type to usb_init_type" missed xhci-omap.c So, fix that patch here, and fix a checkpatch warning. WARNING: Avoid unnecessary line continuations Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: udc: add udc.h include fileTroy Kisky2013-10-20-1/+6
| | | | | | | | | | | | | | Move common definitions to udc.h This allows musb_udc.h to be removed as well. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: split mv_udc.h fileTroy Kisky2013-10-20-0/+121
| | | | | | | | | | | | | | | | | | | | Move defines only needed by mv_udc.c to a file in the same directory. This allows usbtty to compile for mv_udc, but it still doesn't link. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: optimize ep_enableTroy Kisky2013-10-20-2/+2
| | | | | | | | | | | | Only get head if not ep0. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: optimize bounceTroy Kisky2013-10-20-21/+16
| | | | | | | | | | | | | | | | | | | | | | Only perform one copy, either in the bounce routine for IN transfers, or the debounce rtn for OUT transfer. On out transfers, only copy the number of bytes received from the bounce buffer Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: fix full speed connectionsTroy Kisky2013-10-20-14/+34
| | | | | | | | | | | | | | Set maximum packet length in queue header to wMaxPacketSize of endpoint. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: ehci-mx6: add support for otg portTroy Kisky2013-10-20-40/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously, only host1 was supported using an index of 0. Now, otg has index 0, host1 is 1, host2 is 2, host3 is 3. Since OTG requires usbmode to be set after reset, I added CONFIG_EHCI_HCD_INIT_AFTER_RESET to nitrogen6x.h and mx6qsabreauto.h. I also added a weak function board_ehci_power to handle turning power on/off for otg. Type is type of device connected (USB stick vs Host.) Init is type of device desired. Only power up port if type == init == USB_INIT_HOST. Only return error if type != init. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: don't check CONFIG_USB_MAX_CONTROLLER_COUNTTroy Kisky2013-10-20-4/+0
| | | | | | | | | | | | | | | | i.mx6 has 1 otg controller, and 3 host ports. So, CONFIG_USB_MAX_CONTROLLER_COUNT can be greater than 1 even though only 1 device mode controller is supported. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: ehci-hcd: add enum usb_init_type parameter to ehci_hcd_init.Troy Kisky2013-10-20-25/+46
| | | | | | | | | | | | | | This paramter will later be used to initialize OTG ports in host or device mode. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: add enum usb_init_type parameter to usb_lowlevel_initTroy Kisky2013-10-20-10/+10
| | | | | | | | | | | | This parameter will later be used to verify OTG ports. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: am437x: Add support for am437x xhci USB hostDan Murphy2013-10-20-0/+23
| | | | | | | | | | | | | | | | | | Add the support for the am437x xhci usb host. The xHCI host on AM437 is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | usb: dra7xx: Add support for dra7xx xhci USB hostDan Murphy2013-10-20-6/+45
| | | | | | | | | | | | | | | | | | | | | | Add the support for the dra7xx xhci usb host. dra7xx does not contain an EHCI controller so the headers can be removed from the board file. The xHCI host on dra7xx is connected to a usb2 phy so need to add support to enable those clocks. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | usb: omap: Move the usb phy code to the usb/phy directoryDan Murphy2013-10-20-169/+200
| | | | | | | | | | | | | | | | | | | | | | Moving the usb/phy code from xhci-omap to the usb/phy directory and moving the associated phy code over to the new file. Newer TI processors adding xHCI support will have different PHY configurations so therefore abstracting this code away will prevent messing around with the xhci-omap file itself. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | usb: omap5: Update the board_usb_init apiDan Murphy2013-10-20-3/+4
| | | | | | | | | | | | | | | | | | | | Recent patches declares board_usb_init function prototype for a new usb architecture. Turning on the OMAP_XHCI defines cause a redefinition compiler failure. So update the board_usb_init to the latest prototype. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | usb: omap: Move the xhci-omap header file to common locationDan Murphy2013-10-20-1/+1
| | | | | | | | | | | | | | Moving the xhci-omap header to a more global location so that other code can reference this code. Signed-off-by: Dan Murphy <dmurphy@ti.com>
* | usb:g_dnl: Support for TIZEN's THOR function in generic download codeLukasz Majewski2013-10-20-2/+8
| | | | | | | | | | | | | | Support of "thor" function in generic download code (g_dnl.c). Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* | usb:g_dnl:f_thor: USB download function to support TIZEN's THOR protocolLukasz Majewski2013-10-20-0/+1128
| | | | | | | | | | | | | | Implementation of USB download function which supports THOR protocol. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* | usb:g_dnl: Add name parameter to g_dnl_bind_fixup functionLukasz Majewski2013-10-20-2/+2
| | | | | | | | | | | | | | | | | | New parameter, namely *name has been added to g_dnl_bind_fixup(). It is necessary (for compatibility reasons) to assign new USB idProduct and idVendor for different usb functions. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* | usb:g_dnl: Replace static usb_configuration structure with dynamically ↵Lukasz Majewski2013-10-20-8/+16
| | | | | | | | | | | | | | | | | | | | allocated one When the usb_configuration structure is declared as static, it is very hard to assure, that relevant fields (as e.g. config->interfaces[]) are cleared out before new call to g_dnl related functions. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* | usb:udc:s3c: Reduce dcache invalidate range for UDC receive bufferLukasz Majewski2013-10-20-1/+2
| | | | | | | | | | | | | | | | | | The s3c udc driver sends data in a max packet size. Therefore the dcache invalidate range shall be equal to max packet, not the entire DMA_BUFFER_SIZE. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* | usb:smsx95xx LED activity for USB net driverSuriyan Ramasami2013-10-20-0/+14
| | | | | | | | | | | | | | Add LED activity for SMSX95XX USB Ether driver. Signed-off-by: “Suriyan Ramasami" <suriyan.r@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* | usb: new board-specific USB init interfaceMateusz Zalega2013-10-20-19/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit unifies board-specific USB initialization implementations under one symbol (usb_board_init), declaration of which is available in usb.h. New API allows selective initialization of USB controllers whenever needed. Signed-off-by: Mateusz Zalega <m.zalega@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com>
* | usb: gadget: mv_udc: clear desc upon ep_disableTroy Kisky2013-10-20-0/+3
| | | | | | | | | | | | | | desc is set at ep_enable, so for symmetry, clear it at ep_disable. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: zero transfer descriptor memory on probeTroy Kisky2013-10-20-0/+1
| | | | | | | | | | | | Since we flush the TD, we may as well set it to a known value. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* | usb: gadget: mv_udc: flush item before headTroy Kisky2013-10-20-3/+2
| | | | | | | | | | | | | | | | Make sure the transfer descriptor is flushed before the queue is updated so that the controller will not see old information. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
generated by cgit v1.1 at 2024-10-20 00:42:17 +0000