summaryrefslogtreecommitdiff
path: root/drivers/usb
Commit message (Collapse)AuthorAgeLines
* convert common files to new SoC accessJens Scharsig2010-02-12-0/+5
| | | | | | | | * add's a warning to all files, which need update to new SoC access * convert common files in cpu/../at91 and a lot of drivers to use c stucture SoC access Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* musb: Add host support for DM365 EVMPrathap Srinivas2010-02-03-2/+20
| | | | | | Add support for musb host on DM365 EVM. Signed-off-by: Prathap Srinivas <msprathap@ti.com>
* usb: musb: fix Blackfin DMA register paddingCliff Cai2010-02-03-1/+1
| | | | | | | | | The conversion from offsets to C structs lost a little padding in the DMA register map. Accessing endpoints other than ep0 with DMA would fail as the addresses wouldn't be adjusted correctly. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* SPEAr : usbd driver support for SPEAr SoCsVipin KUMAR2010-01-23-0/+999
| | | | | | | | | | | | | SPEAr SoCs contain a synopsys usb device controller. USB Device IP can work in 2 modes - DMA mode - Slave mode The driver adds support only for slave mode operation of usb device IP. This driver is used along with standard USBTTY driver to obtain a tty interface over USB on the host Signed-off-by: Vipin <vipin.kumar@st.com>
* PCIe, USB: Replace 'end point' references with 'endpoint'Peter Tyser2010-01-17-1/+1
| | | | | | | | | When referring to PCIe and USB 'endpoint' is the standard naming convention. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: add virtual root hub control supportBryan Wu2010-01-12-2/+482
| | | | | | | | | For MUSB devices that do not support multipoint (hubs), we have to emulate a root hub so that we can support core operations like resetting ports. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Add ppc440epx USB ehci support.Chris Zhang2010-01-09-0/+49
| | | | | | | Currently ppc440epx uses OHCI for USB full-speed support. This change adds support for EHCI. Signed-off-by: Chris Zhang <chris@seamicro.com>
* Fix EHCI port reset.Chris Zhang2010-01-09-0/+3
| | | | | | | | | In USB ehci driver, the port reset is not terminated. EHCI spec says "A host controller must terminate the reset and stabilize the state of the port within 2 milliseconds". Without termination, a port stays at reset state. This is observed on ppc4xx(sequoia) boards. Signed-off-by: Chris Zhang <chris@seamicro.com>
* omap3: fix compile warningSanjeev Premi2010-01-09-0/+3
| | | | | | | | | | | This patch fixes this warning during compile: omap3.c: In function 'musb_platform_init': omap3.c:126: warning: label 'end' defined but not used Problem reported by: Dirk Behme[dirk.behme@googlemail.com] Signed-off-by: Sanjeev Premi <premi@ti.com>
* usb: musb: add support for Blackfin MUSBBryan Wu2010-01-09-1/+262
| | | | | | | Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: change rxcsr register from write to read/modify/writeBryan Wu2010-01-09-2/+4
| | | | | | | | | | | | | The RX Control/Status register has bits that we want to preserve, so don't just write out a single bit. Preserve the others bits in the process. The original code posted to the u-boot list had this behavior, but looks like it was lost somewhere along the way to merging. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: make multipoint optionalBryan Wu2010-01-09-0/+20
| | | | | | | | | | The multipoint handling under MUSB is optional, and some parts (like the Blackfin processor) do not implement support for it. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: make fifo support configurableBryan Wu2010-01-09-4/+14
| | | | | | | | | | | | | The dynamic FIFO handling under MUSB is optional, and some parts (like the Blackfin processor) do not implement support for it. Due to this, the FIFO reading/writing steps need special handling, so mark the common versions weak so drivers can override. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: make sure the register layout is packedMike Frysinger2010-01-09-1/+1
| | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* DA8xx: Add MUSB host supportAjay Kumar Gupta2010-01-09-0/+243
| | | | | | | Tested USB host functionality on DA830 EVM. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Swaminathan S <swami.iyer@ti.com>
* OMAP3 USB Initialize twl4030 only if requiredTom Rix2009-12-20-1/+6
| | | | | | | OMAP3EVM uses ISP1504 phy and so twl4030 related init is not required. Submitted-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* OMAP3 Add usb device supportTom Rix2009-12-20-2/+1393
| | | | | | | | | | | | This change adds the usb device support for musb. Omap3 platform support added at the same level as davinci. The interface for usbtty to use the musb device support was added. Verified on omap3 beagle, zoom1 and zoom2. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* TWL4030 Add usb PHY supportTom Rix2009-12-20-0/+233
| | | | | | | | | | The twl4030 provides a PHY device for connecting a link device, like musb, to physical connection. This change adds the twl4030 usb registers and functions for initializing the PHY as required by omap3. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* USB Consolidate descriptor definitionsTom Rix2009-12-20-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The header files usb.h and usbdescriptors.h have the same nameed structure definitions for usb_config_descriptor usb_interface_descriptor usb_endpoint_descriptor usb_device_descriptor usb_string_descriptor These are out right duplicates in usb.h usb_device_descriptor usb_string_descriptor This one has extra unused elements usb_endpoint_descriptor unsigned char bRefresh unsigned char bSynchAddress; These in usb.h have extra elements at the end of the usb 2.0 specified descriptor and are used. usb_config_descriptor usb_interface_descriptor The change is to consolidate the definition of the descriptors to usbdescriptors.h. The dublicates in usb.h are removed. The extra element structure will have their name shorted by removing the '_descriptor' suffix. So usb_config_descriptor -> usb_config usb_interface_descriptor -> usb_interface For these, the common descriptor elements are accessed now by an element 'desc'. As an example - if (iface->bInterfaceClass != USB_CLASS_HUB) + if (iface->desc.bInterfaceClass != USB_CLASS_HUB) This has been compile tested on MAKEALL arm, ppc and mips. Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
* Add a unified s3c24x0 header filekevin.morfitt@fearnside-systems.co.uk2009-11-27-2/+1
| | | | | | | | | | This patch adds a unified s3c24x0 cpu header file that selects the header file for the specific s3c24x0 cpu from the SOC and CPU configs defined in board config file. This removes the current chain of s3c24-type #ifdef's from the s3c24x0 code. Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xxMinkyu Kang2009-11-27-1/+1
| | | | | | | This patch moves the s3c64xx header files from include/ to include/asm-arm/arch-s3c64xx Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* usb: bugfix driver/usb/host/ehci-hcd.c function ehci_submit_rootPrafulla Wadaskar2009-07-23-2/+2
| | | | | | | | | | | | This change is cheked in Linux source and fix found to be in sync. This patch is tested for USB host interface on Kirkwood based Sheevaplug platform (ARM little endian board) Risk: the impact of this patch is not validated on big endian board. This need to be checked... Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* Coding Style cleanup; update CHANGELOG.Wolfgang Denk2009-07-23-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* stdio/device: rework function naming conventionJean-Christophe PLAGNIOL-VILLARD2009-07-18-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | So far the console API uses the following naming convention: ======Extract====== typedef struct device_t; int device_register (device_t * dev); int devices_init (void); int device_deregister(char *devname); struct list_head* device_get_list(void); device_t* device_get_by_name(char* name); device_t* device_clone(device_t *dev); ======= which is too generic and confusing. Instead of using device_XX and device_t we change this into stdio_XX and stdio_dev This will also allow to add later a generic device mechanism in order to have support for multiple devices and driver instances. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Edited commit message. Signed-off-by: Wolfgang Denk <wd@denx.de>
* usb: Fix compiler warning with gcc4.4Kumar Gala2009-07-11-2/+2
| | | | | | | | | ehci-hcd.c: In function 'ehci_submit_root': ehci-hcd.c:719: warning: value computed is not used ehci-hcd.c:748: warning: value computed is not used Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: add Marvell Kirkwood ehci host controller driverPrafulla Wadaskar2009-07-09-0/+109
| | | | | | | This driver is tested on Sheevaplug platform Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: fix: access of ehci struct elementsVivek Mahajan2009-07-09-9/+9
| | | | | | | | | This patch fixes the access to the 'ehci' struct elements which should have been taken care off in 4ef01010aa4799c759d75e67007fdd3a38c88c8a Sorry about that. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: add timeout via CONFIG_MUSB_TIMEOUTBryan Wu2009-07-09-0/+35
| | | | | | Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb: musb: drop old musb read/write prototypesMike Frysinger2009-07-09-6/+0
| | | | | | | These functions are no longer defined, so remove their prototypes. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc83xx: USB: Reorganized its supportVivek Mahajan2009-06-12-35/+18
| | | | | | | | | | | | | | | | | The following patch reorganizes/reworks the USB support for mpc83xx as under:- * Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to cpu/mpx83xx/cpu_init.c * Board specific usb_phy_type is read from the environment * Adds USB EHCI specific structure in include/usb/ehci-fsl.h * Copyrights revamped in most of the following files Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: Relocates ehci-fsl.h to include/usbVivek Mahajan2009-06-12-87/+1
| | | | | | | | The following patch moves 8xxx-specifc USB #defines from drivers/usb/host/ehci-fsl.h to include/usb. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* mpc8xxx: USB: Removed reenablement of its interfaceVivek Mahajan2009-06-12-4/+0
| | | | | | | | | | To prepare for the 85xx USB support, which requires interface enablement only once in (specified) order, no different than instructions for enabling the interface under 83xx. It is unknown why the original author enabled the interface twice (checked for references in errata, etc). Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* at91: fix a USB problem for AT91SAM9261RONETIX - Ilko Iliev2009-06-09-1/+2
| | | | | | | | | | | | This patch corrects the missing PLLB initialization in usb_cpu_init() for AT91SAM9261. Because of the missing PLLB initialization, the USB support for all AT91SAM9261 based boards will work only if the PLLB is configured by a precedent bootloader. Signed-off-by: Ilko Iliev <iliev@ronetix.at> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* Fix e-mail address of Gary Jennejohn.Detlev Zundel2009-05-15-2/+2
| | | | Signed-off-by: Detlev Zundel <dzu@denx.de>
* Replace __attribute references with __attribute__Peter Tyser2009-04-28-5/+5
| | | | | | | | __attribute__ follows gcc's documented syntax and is generally more common than __attribute. This change is only asthetic and should not affect functionality. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD2009-04-16-1/+2
| | | | | | calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Support for PXA27X UDC.Remy Bohmer2009-04-06-0/+703
| | | | | | | | This Patch adds Support for PXA27X UDC. (Rebased to drivers/usb reorganisation) Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* drivers/usb: regorganisationJean-Christophe PLAGNIOL-VILLARD2009-04-06-46/+178
| | | | | | | | | | | | | move to linux usb driver organisation as following drivers/usb/gadget drivers/usb/host drivers/usb/musb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* at91: move usb driver to drivers/usbJean-Christophe PLAGNIOL-VILLARD2009-04-04-0/+81
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* s3c64xx: move usb driver to drivers/usbJean-Christophe PLAGNIOL-VILLARD2009-03-29-0/+46
| | | | | | add CONFIG_USB_S3C64XX to activate the driver Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* r8a66597-hcd: fix cannot use external hubYoshihiro Shimoda2009-02-22-5/+31
| | | | | | | | Fix the problem that cannot use external hub, because this driver did not control correctly a DEVADDx register. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* Coding style cleanup; update CHANGELOGWolfgang Denk2009-02-12-4/+4
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Fix whitespace damage: double space changed to a tabJerry Van Baren2009-02-11-1/+1
| | | | | | | | | | At some point an intentional double space at the end of the sentence got changed into a tab in the GPL header line: * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the This patch fixes the damage. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
* USB: Add EHCI support for VCT EHCI controller (really with driver now)Stefan Roese2009-02-02-0/+58
| | | | | | | | Somehow I missed the real driver part in my last patch version. This patch now adds the driver. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* USB: Add dcache support to the EHCI driverStefan Roese2009-01-28-0/+103
| | | | | | | | | This patch adds routines to handle (flush/invalidate) the dcache for the QH and qTD structures and data buffers. This is needed on platforms using this EHCI support with dcache enabled (like the MIPS VCT board port). Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* USB: Add EHCI support for VCT EHCI controllerStefan Roese2009-01-28-0/+1
| | | | | Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* USB: Add config option to call ehci_hcd_init() again after EHCI resetStefan Roese2009-01-28-0/+5
| | | | | | | | | | This patch adds the config option CONFIG_EHCI_HCD_INIT_AFTER_RESET to call ehci_hcd_init() again after ehci_reset() is executed. This is needed for the upcoming VCT EHCI support which needs to re-init the hcd part again after the EHCI CMD_RESET is executed. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* USB: Fix speed detection on EHCI cntr with root hub transaction translatorsStefan Roese2009-01-28-1/+16
| | | | | | | | | This patch fixes an issue that the speed of USB devices was not detected correctly on some EHCI controllers. This will be used on the upcoming VCT EHCI support. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb : musb : Adding DM6446 (TI DaVinci) platform specific USB supportThomas Abraham2009-01-28-0/+194
| | | | | | | | | | | Adding DM6446 (TI DaVinci) platform specific USB functionality for USB Phy and VBUS initialization. Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Swaminathan S <swami.iyer@ti.com> Signed-off-by: Thomas Abraham <t-abraham@ti.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* usb : musb : Adding host controller driver for Mentor USB controllerThomas Abraham2009-01-28-0/+1302
| | | | | | | | | | | Adding Mentor USB core functionality and Mentor USB Host controller functionality for Mentor USB OTG controller (musbhdrc). Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Swaminathan S <swami.iyer@ti.com> Signed-off-by: Thomas Abraham <t-abraham@ti.com> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>