summaryrefslogtreecommitdiff
path: root/drivers/usb/gadget
Commit message (Collapse)AuthorAgeLines
...
* usb:gadget:ums: Replace malloc calls with memalign to fix cache buffer alignmentLukasz Majewski2014-02-06-2/+2
| | | | | | | | Calls to malloc() have been replaced by memalign. It now provides proper buffer alignment. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb: gadget: fotg210: EP0 fifo empty indication is non-reliableKuo-Jung Su2014-01-13-0/+1
| | | | | | | | | | | | | | | | | | The fifo size of ep0 is 64 bytes, and if the packet size grater than 64 bytes, the driver would have to fill up the fifo multiple times, and before filling up the fifo, the driver should make sure the fifo is empty by checking fifo empty indication. However there is a hardware bug that the fifo empty indication is somehow a bit earlier than fifo reset. So if I don't add an extra delay here, the data might be corrupted. (i.e., 1 byte missing) After a couple of tests, it truns out that 1 usec is good enough. This workaround should be applied to all hardware revisions. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Marek Vasut <marex@denx.de>
* usb: gadget: fotg210: add w1c interrupt status supportKuo-Jung Su2014-01-13-0/+14
| | | | | | | | | | | | | | Since hardware revision 1.11.0, the following interrupt status registers are now W1C (i.e., write 1 clear): 1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5) 2. Interrupt Source Group 2 Register (0x14C) (All bits) And before revision 1.11.0, these registers are all R/W. Which means software must write a 0 to clear the status. Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com> CC: Marek Vasut <marex@denx.de>
* usb: f_dfu: cosmetic: Code cleanupLukasz Majewski2013-12-18-2/+2
| | | | | | Code cleanup for dfu_bind_config function Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* usb: dfu: f_dfu: Provide infrastructure to adjust DFU's Poll Timeout valueLukasz Majewski2013-12-18-3/+38
| | | | | | | | | | | It is necessary to deter the host from sending subsequent DFU_GETSTATUS request in the case of e.g. writing the buffer to medium. Here the timeout is increased when we fill up the whole buffer. This delay allows eMMC memory to perform its internal operations. Otherwise we end up with HOST's error regarding GET_STATUS receive timeout. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* drivers/usb/gadget: select objects by obj-$(CONFIG-...)Masahiro Yamada2013-12-13-6/+2
| | | | | | | | | | | | Before switching to the real Kbuild, drivers/usb/gadget/Makefile must be fixed. If none of CONFIG_USB_GADGET, CONFIG_USB_ETHER, CONFIG_USB_DEVICE is defined, both obj- and obj-y get empty. We need non-empty obj- or obj-y on each Makefile to generate built-in.o on the real Kbuild. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* driver:usb:s3c_udc: add support for Exynos4x12Piotr Wilczek2013-12-02-2/+12
| | | | | | | | This patch add new defines for usb phy for Exynos4x12. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* usb, g_dnl: make bcdDevice value configurableHeiko Schocher2013-11-12-4/+19
| | | | | | | | | | | add the possibility to set the bcdDevice number board specific. Therefore the weak function g_dnl_get_board_bcd_device_number() is introduced. Used on the siemens boards. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
* usb, g_dnl: make iSerialNumber board configurableHeiko Schocher2013-11-08-0/+20
| | | | | | | | | | | | | | add the possibility to set the iSerialNumber board specific. Default value for iSerialNumber is 0x0. This value can changed board specific through the new function g_dnl_set_serialnumber() which must be called from the board specific function g_dnl_bind_fixup(). Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
* usb: ums: add ums exit feature by ctrl+c or by detach usb cablePrzemyslaw Marczak2013-11-08-3/+21
| | | | | | | | | | | | | | | This patch allows exiting from UMS mode to u-boot prompt by detaching usb cable or by pressing ctrl+c. Add new config: CONFIG_USB_CABLE_CHECK. If defined then board file should provide function: usb_cable_connected() (include/usb.h) that return 1 if cable is connected and 0 otherwise. Changes v2: - add a note to the README Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb: ums: fix disk capacity miscalculation and code cleanupPrzemyslaw Marczak2013-11-08-23/+3
| | | | | | | | | | | | | | This patch prevents: - ums disk capacity miscalculation because of integer overflow Changes v2: - Prevents passing zero size disk capacity to ums gadget driver - Change function ums_get_capacity() to ums_disk_init() and do ums disk initialization before gadget init - Remove unnecessary code from mass storage driver Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb: ums: code refactoring to improve reusability on other boards.Przemyslaw Marczak2013-11-08-23/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces some cleanups to ums code. Changes: ums common: - introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in usb_mass_storage.h both default values as 0 if board config doesn't define them common cleanup changes: - change name of struct "ums_board_info" to "ums" - "ums_device" fields are moved to struct ums and "dev_num" is removed - change function name: board_ums_init to ums_init - remove "extern" prefixes from usb_mass_storage.h cmd_usb_mass_storage: - change error() to printf() if need to print info message - change return values to command_ret_t type at ums command code - add command usage string Changes v2: ums common: - always returns number of read/write sectors - coding style clean-up ums gadget: - calculate amount of read/write from device returned value. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com>
* drivers: usb: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-41/+19
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* usb: udc: add udc.h include fileTroy Kisky2013-10-20-0/+4
| | | | | | | Move common definitions to udc.h This allows musb_udc.h to be removed as well. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: split mv_udc.h fileTroy Kisky2013-10-20-0/+121
| | | | | | | | | | Move defines only needed by mv_udc.c to a file in the same directory. This allows usbtty to compile for mv_udc, but it still doesn't link. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: optimize ep_enableTroy Kisky2013-10-20-2/+2
| | | | | | Only get head if not ep0. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: optimize bounceTroy Kisky2013-10-20-21/+16
| | | | | | | | | | | Only perform one copy, either in the bounce routine for IN transfers, or the debounce rtn for OUT transfer. On out transfers, only copy the number of bytes received from the bounce buffer Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: fix full speed connectionsTroy Kisky2013-10-20-14/+34
| | | | | | | Set maximum packet length in queue header to wMaxPacketSize of endpoint. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: don't check CONFIG_USB_MAX_CONTROLLER_COUNTTroy Kisky2013-10-20-4/+0
| | | | | | | | i.mx6 has 1 otg controller, and 3 host ports. So, CONFIG_USB_MAX_CONTROLLER_COUNT can be greater than 1 even though only 1 device mode controller is supported. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: add enum usb_init_type parameter to usb_lowlevel_initTroy Kisky2013-10-20-1/+1
| | | | | | This parameter will later be used to verify OTG ports. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb:g_dnl: Support for TIZEN's THOR function in generic download codeLukasz Majewski2013-10-20-2/+8
| | | | | | | Support of "thor" function in generic download code (g_dnl.c). Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb:g_dnl:f_thor: USB download function to support TIZEN's THOR protocolLukasz Majewski2013-10-20-0/+1128
| | | | | | | Implementation of USB download function which supports THOR protocol. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb:g_dnl: Add name parameter to g_dnl_bind_fixup functionLukasz Majewski2013-10-20-2/+2
| | | | | | | | | New parameter, namely *name has been added to g_dnl_bind_fixup(). It is necessary (for compatibility reasons) to assign new USB idProduct and idVendor for different usb functions. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb:g_dnl: Replace static usb_configuration structure with dynamically ↵Lukasz Majewski2013-10-20-8/+16
| | | | | | | | | | allocated one When the usb_configuration structure is declared as static, it is very hard to assure, that relevant fields (as e.g. config->interfaces[]) are cleared out before new call to g_dnl related functions. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
* usb:udc:s3c: Reduce dcache invalidate range for UDC receive bufferLukasz Majewski2013-10-20-1/+2
| | | | | | | | | The s3c udc driver sends data in a max packet size. Therefore the dcache invalidate range shall be equal to max packet, not the entire DMA_BUFFER_SIZE. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb: gadget: mv_udc: clear desc upon ep_disableTroy Kisky2013-10-20-0/+3
| | | | | | | desc is set at ep_enable, so for symmetry, clear it at ep_disable. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: zero transfer descriptor memory on probeTroy Kisky2013-10-20-0/+1
| | | | | | Since we flush the TD, we may as well set it to a known value. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: flush item before headTroy Kisky2013-10-20-3/+2
| | | | | | | | Make sure the transfer descriptor is flushed before the queue is updated so that the controller will not see old information. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: set is_dualspeed = 1Troy Kisky2013-10-20-0/+1
| | | | | | This controller support full and high speed. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: mv_udc: fix typo in error messageTroy Kisky2013-10-20-2/+2
| | | | | | Change 'nfo=' to 'info=' Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: ether: return error from rx_submit if no requestTroy Kisky2013-10-20-0/+2
| | | | | | | | | | | | | | | | | | | | This prevents a crash if tftpboot is given a bad filename. rx_req will be released by eth_reset_config which is called by eth_disconnect, which is called using the .disconnect member of usb_gadget_driver by mv_pullup in mv_udc which is called using the .pullup member of usb_gadget_ops by usb_gadget_disconnect which is called by usb_eth_halt which is called using the .halt member of eth_device by eth_halt which is called by TftpHandler when TFTP_ERR_FILE_NOT_FOUND or TFTP_ERR_ACCESS_DENIED occurs I trigger this with the following commands setenv ipaddr 10.0.0.2 && setenv netmask 255.255.255.0 && setenv serverip 10.0.0.1 setenv usbnet_devaddr 00:11:22:33:44:55 && setenv usbnet_hostaddr 00:aa:bb:cc:dd:ee setenv ethprime usb_ether && setenv ethact usb_ether && setenv ncip 10.0.0.1 tftpboot 10800000 10.0.0.1:missing_file Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* usb: gadget: ether set wMaxPacketSizeTroy Kisky2013-10-20-0/+2
| | | | | | | | | | | | | | | | | | | | | set wMaxPacketSize for full speed descriptors fs_source_desc, fs_sink_desc to 64. Full-speed bulk endpoint can have a maximum packet size of 8, 16, 32, or 64 bytes, so choice 64. The hs_source_desc, hs_sink_desc, already have their wMaxPacketSize set to 512. That is the only legal value for high speed bulk endpoints. Strictly speaking, this patch is not needed because usb_ep_autoconfig will call ep_matches which will override wMaxPacketSize for BULK endpoints only with the size associated with the endpoint setup by the udc driver. But if you want to rely on this, you may as well combine the full speed descriptor with the high speed descriptor to minimize confusion. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* Coding Style cleanup: drop some excessive empty linesWolfgang Denk2013-10-14-5/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-14-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* USB: gadget: atmel: disconnect before unbindBo Shen2013-09-24-1/+2
| | | | | | When unbind the gadget driver, need call disconnect first. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* usb:g_dnl:dfu: Download gadget and DFU function code clean upLukasz Majewski2013-09-24-4/+1
| | | | | | | | | | | | The download gadget code and DFU function lacks of proper declarations for the case when a target board wants to use only one of available usb functions. Moreover the relevant declarations have been moved to consistent localization (like <dfu.h>). Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb:gadget:Remove redundant #includes for USB composite gadget and its functionsLukasz Majewski2013-09-24-1/+0
| | | | | | | | | | Only the <linux/usb/gadget.h> requires error.h include. Hence, several includes of error.h at USB gadget functions are not needed. Moreover unnecessary malloc.h includes were also removed. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* usb:g_dnl:ums: Conditional compilation for mass storage function ↵Lukasz Majewski2013-09-24-1/+2
| | | | | | | | | | | | | | | (f_mass_storage) The mass storage composite function is now compiled in only when CONFIG_USB_GADGET_MASS_STORAGE is defined. Such change provides binary size reduction for boards which use USB download gadget (like am335x_evm) with DFU, but don't use UMS. For example at am335x_evm board reduction is more than 2KiB for text and around 120B for data. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de>
* USB: gadget: add atmel usba udc driverBo Shen2013-09-24-0/+1632
| | | | | | | | | | | | | | | | | Add atmel usba udc driver support, porting from Linux kernel The original code in Linux Kernel information is as following commit e01ee9f509a927158f670408b41127d4166db1c7 Author: Jingoo Han <jg1.han@samsung.com> Date: Tue Jul 30 17:00:51 2013 +0900 usb: gadget: use dev_get_platdata() Use the wrapper function for retrieving the platform data instead of accessing dev->platform_data directly. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* usb: gadget: config: fix unaligned access issuesTroy Kisky2013-09-24-2/+4
| | | | | | | | | | | As seen with codesourcery compiler 2010q1, the buf pointer in usb_request structure is not aligned on 4 bytes boundary causing data aborts in eth_setup -> conf_buf -> usb_gadget_config_buf. Make it as align access to fix this issue. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> [voice.shen@atmel.com: add commit message] Signed-off-by: Bo Shen <voice.shen@atmel.com>
* usb: gadget: Fix data aborts during USB ethernet bootJoel Fernandes2013-09-24-2/+3
| | | | | | | | | | | | | | As seen on GCC 4.6 Linaro compiler, control_req buffer is not aligned on 4 byte boundaray causing data aborts in eth_setup -> conf_buf during dhcp boot over usb_ether. Fix the issue my aligning control_req buffer using DEFINE_CACHE_ALIGN_BUFFER. Tested on am335x_evm platform (beaglebone). Applies on 2013.10-rc1 branch. Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Joel Fernandes <joelf@ti.com>
* usb:dfu:g_dnl: Refactoring the string definition code for g_dnl driverLukasz Majewski2013-08-26-4/+7
| | | | | | | | | | The manufacturer and product IDs are dynamically assigned when gadget is bind. Now the IDs aren't assigned at struct g_dnl_string_defs definition. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: "Egli, Samuel" <samuel.egli@siemens.com>
* usb:dfu:g_dnl: Change number of exported configurations at composite gadgetLukasz Majewski2013-08-26-2/+4
| | | | | | | | | | | | | | | | | | | USB composite gadget (g_dnl) supports only one configuration. Due to that the corresponding field - bConfigurationValue has been changed. Moreover more descriptive names were chosen for relevant fields. Windows XP setup: - Thesyscon USB Descriptor Dumper - zadig_xp program for WinUSB installation (which is required by dfu-util) - dfu-util for windows (version 0.6) - TRATS target connected via USB hub to test Win XP machine. Tested at: Trats - Exynos4210 Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: "Egli, Samuel" <samuel.egli@siemens.com>
* SPDX-License-Identifier: convert BSD-3-Clause filesWolfgang Denk2013-08-19-29/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini Don't remove some copyrights by accident] Signed-off-by: Tom Rini <trini@ti.com>
* dfu: Implementation of target reset after communication with dfu-util's -R ↵Lukasz Majewski2013-07-29-0/+2
| | | | | | | | | | | | | | switch This patch extends dfu code to support transmission with -R switch specified at dfu-util. When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after successful data transmission. Then dfu resources are released and reset command is issued. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* usb: mv_udc: Add bounce bufferMarek Vasut2013-07-29-7/+77
| | | | | | | | | | | | The requests sent to the controller are not properly cache aligned most of the time, thus implement a simple bounce buffer to avoid problem with cache. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
* usb: mv_udc: Add proper cache managementMarek Vasut2013-07-29-5/+77
| | | | | | | | | | | | | Implement functions to flush/invalidate dcache over QH and qTDs and make use of them where appropriate. Also use them to replace the old incorrect cache management attempt. This is the first step towards making this driver work with data cache enabled. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
* usb: mv_udc: Implement better qTD item accessorMarek Vasut2013-07-29-2/+15
| | | | | | | | | | | | The code for retrieving qTD item for particular endpoint is hard to understand, moreover it's duplicated all over the driver. Move the code into single nice and documented function. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
* usb: mv_udc: Improve allocation of qTD itemsMarek Vasut2013-07-29-2/+23
| | | | | | | | | | | | | Allocate the qTD items all at once instead of allocating them separately. Moreover, make sure each qTD is properly aligned to 32-bytes boundary and that cache can be safely flushed over each qTD touple. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
* usb: mv_udc: Implement better QH accessorMarek Vasut2013-07-29-5/+18
| | | | | | | | | | | | The code for retrieving QH for particular endpoint is hard to understand, moreover it's duplicated all over the driver. Move the code into single nice and documented function. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-12-29 02:51:44 +0000