summaryrefslogtreecommitdiff
path: root/drivers/spi/ti_qspi.c
Commit message (Collapse)AuthorAgeLines
* spi: ti_qspi: Use BIT macroJagan Teki2015-10-27-5/+5
| | | | | | | | | | | | Replace numerical bit shift with BIT macro in ti_qspi :%s/(1 << nr)/BIT(nr)/g where nr = 0, 1, 2 .... 31 Reviewed-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
* spi: ti_qspi: Use DMA to read from qspi flashVignesh R2015-08-17-0/+25
| | | | | | | | ti_qspi uses memory map mode for faster read. Enabling DMA will increase read speed by 3x @48MHz on DRA74 EVM. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* ti: qspi: set flash quad bit based on quad support flagvishalm@ti.com2015-08-17-1/+1
| | | | | | | | Update op_mode_rx flag based on CONFIG_QSPI_QUAD_SUPPORT flag, instead of platform. Signed-off-by: Vishal Mahaveer <vishalm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* qspi: dra7x: enable quad mode read for ti-qspi driverRavi Babu2015-03-30-0/+7
| | | | | | | | This patch enables QUAD read mode for qspi to improve the read performace while loading the binaries from qspi. Signed-off-by: Ravi Babu <ravibabu@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* arm: omap: add support for am57xx devicesFelipe Balbi2014-12-04-4/+4
| | | | | | | | just add a few ifdefs around because this device is very similar to dra7xxx. Signed-off-by: Felipe Balbi <balbi@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* ti: qspi: populate slave device to set flash quad bit.Sourav Poddar2014-06-06-0/+1
| | | | | | | The patch populates the slave data which will be used by flash driver to set the flash quad enable bit. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
* spi: ti_qspi: Add delay for successful bulk erase.Poddar, Sourav2014-04-17-0/+3
| | | | | | | | Bulk erase is not happening properly on dra7 due to erase timing constraints, add a delay so that erase timing constraints are properly met. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Tested-by: Yebio Mesfin <ymesfin@ti.com>
* spi: ti_qspi: Add delay before xfer for am43xxSourav Poddar2014-02-18-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without this delay, write/read is failing. Looks like, the WIP always remain set and hence a timeout occurs leading to the error. Without this patch, device does not get probed also. Here is the log. U-Boot# U-Boot# U-Boot# U-Boot# sf probe 0 SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff Failed to initialize SPI flash at 0:0 U-Boot# sf probe 0 While with this patch, log is U-Boot# sf probe 0 SF: Detected MX25L51235F with page size 256 Bytes, erase size 64 KiB, total 64 MiB, mapped at 30000000 U-Boot# sf erase 0 0x80000 SF: 524288 bytes @ 0x0 Erased: OK U-Boot# mw 81000000 0xdededede 0x40000 U-Boot# sf write 81000000 0 0x40000 SF: 262144 bytes @ 0x0 Written: OK U-Boot# sf read 82000000 0 0x40000 SF: 262144 bytes @ 0x0 Read: OK U-Boot# md 0x82000000 Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* spi: ti_qspi: Add AM43xx specifics changesSourav Poddar2014-02-18-3/+23
| | | | | | | Add AM43xx specific changes. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* spi: add TI QSPI driverMatt Porter2013-10-07-0/+311
Adds a SPI master driver for the TI QSPI peripheral. - Added quad read support. - Added memory mapped support. Signed-off-by: Matt Porter <matt.porter@linaro.org> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
generated by cgit v1.1 at 2024-11-10 13:45:59 +0000