summaryrefslogtreecommitdiff
path: root/drivers/spi/kirkwood_spi.c
Commit message (Collapse)AuthorAgeLines
* spi: kirkwood_spi: Add support for multiple chip-selects on MVEBUStefan Roese2016-04-06-0/+14
| | | | | | | | | | | | | Currently only chip-select 0 is supported by the kirkwood SPI driver. The Armada XP / 38x SoCs also use this driver and support multiple chip selects. This patch adds support for multiple CS on MVEBU. The register definitions are restructured a bit with this patch. Grouping them to the corresponding registers. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviewed-by: Jagan Teki <jteki@openedev.com>
* spi: kirkwood_spi.c: Add compatible match ID for Armada 375Stefan Roese2016-04-04-0/+1
| | | | | | | | This enables this driver for the Marvell Armada 375 SoC. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Reviwer-by: Jagan Teki <jteki@openedev.com>
* spi: kirkwood_spi.c: Add driver model supportStefan Roese2016-01-14-63/+159
| | | | | | | | | | | | | This patch adds driver model support to the kirkwood SPI driver. Which is also used on the MVEBU SoC's, now being converted to DM. Non-DM support is still available for the "older" platforms using this driver, like kirkwood. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org>
* spi: kirkwood_spi.c: Prepare for driver model supportStefan Roese2016-01-14-13/+28
| | | | | | | | | | | This patch prepares the Kirkwood SPI driver, also used on the MVEBU board (Armada XP / 38x), for the conversion to driver model. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org>
* spi: kirkwood_spi.c: Change KW_SPI_BASE to MVEBU_SPI_BASEStefan Roese2014-10-23-1/+2
| | | | | | | | | | This makes is possible to use this SPI driver from other MVEBU SoC's as well. As the upcoming Armada XP support will do. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Tested-by: Luka Perkov <luka@openwrt.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
* spi: kirkwood_spi.c: Compile MPP (pin-mux) only for kirkwood SoC'sStefan Roese2014-10-23-0/+10
| | | | | | | | | | Compile the pin multiplexing only on Kirkwood platforms. As the Armada XP doesn't need it. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Tested-by: Luka Perkov <luka@openwrt.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
* arm: marvell: Move arch-kirkwood/spi.h to arch-mvebu/spi.hStefan Roese2014-10-23-1/+1
| | | | | | | | | | | This move makes it possible to use this kirkwood SPI driver from other MVEBU platforms as well. This will be used by the upcoming Armada XP support. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Tested-by: Luka Perkov <luka@openwrt.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
* arm: marvell: Move arch/kirkwood.h to arch/soc.hStefan Roese2014-10-23-1/+1
| | | | | | | | | This move makes is possible to use this header not only from kirkwood platforms but from all Marvell mvebu platforms. Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Luka Perkov <luka@openwrt.org> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
* spi: kirkwood_spi.c: cosmetic: Fix minor coding style issuesStefan Roese2014-09-24-8/+6
| | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de> Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Tested-by: Luka Perkov <luka@openwrt.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* spi: kirkwood_spi.c: Make global variable staticStefan Roese2014-09-24-1/+1
| | | | | | | Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Tested-by: Luka Perkov <luka@openwrt.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* spi: kirkwood_spi.c: Some fixes and cleanupStefan Roese2014-09-24-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces the clrsetbits_le32() accessor functions in the kirkwood SPI driver. Note that it also includes a fix: - writel(~KWSPI_CSN_ACT | KWSPI_SMEMRDY, &spireg->ctrl); + writel(KWSPI_SMEMRDY, &spireg->ctrl); Here the bit KWSPI_CSN_ACT (0x1) should have been cleared. Instead 0xfffffffe is written into this control register. This is the main reason to use the clrsetbits() functions now. As they make clearing bits much less error prone. Additionally KWSPI_IRQUNMASK is not used in spi_cs_activate() and spi_cs_deactivate() any more. Its the wrong macro but has the same value as the correct one (KWSPI_CSN_ACT). This is in preparation for use of this driver on the Marvell Armada XP platform as well. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Prafulla Wadaskar <prafulla@marvell.com> Tested-by: Luka Perkov <luka@openwrt.org> Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* spi: Use spi_alloc_slave() in each SPI driverSimon Glass2013-03-19-4/+1
| | | | | | | | Rather than each driver having its own way to allocate a SPI slave, use the new allocation function everywhere. This will make it easier to extend the interface without breaking drivers. Signed-off-by: Simon Glass <sjg@chromium.org>
* kirkwood: make MPP arrays static constAlbert ARIBAUD2013-01-09-7/+5
| | | | | | | | | | This saves stack and code memory for local copy, and consumes initialized data memory. For 22 of the 29 kirkwood-based boards, this results in a global saving of about 30 bytes. For 7 of them, it results in an increase of 6 to 14 bytes. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* kw_spi: fix clock prescaler computationValentin Longchamp2012-09-03-2/+3
| | | | | | | | | | | | | | | | | The computation was not correct with low clock values: setting a 1MHz clock would result in an overlap that would then configure a 25Mhz clock. This patch implements a correct computation method according to the kirkwood functionnal spec. table 600 (Serial Memory Interface Configuration Register). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> Acked-by: Prafulla Wadaskar <Prafulla@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
* kw_spi: add weak functions board_spi_claim/release_busValentin Longchamp2012-07-07-1/+12
| | | | | | | | | | This allows a final, board specific, step in the claim/relase_bus function for the SPI controller, which may be needed for some hardware designs. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* kw_spi: support spi_claim/release_bus functionsValentin Longchamp2012-07-07-0/+36
| | | | | | | | | | | | | These two function nows ensure that the MPP is configured correctly for the SPI controller before any SPI access, and restore the initial configuration when the access is over. Since the used pins for the SPI controller can differ (2 possibilities for each signal), the used pins are configured with CONFIG_SYS_KW_SPI_MPP. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* kw_spi: backup and reset the MPP of the chosen CS pinValentin Longchamp2012-07-07-9/+6
| | | | | | | | | This was not done before, and in the case of a shared pin (for MPP0 between NF_IO[2] and CSn) this could lead to problems. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* kirkwood_spi: correct access to irq_mask registerIan Campbell2012-02-12-1/+1
| | | | | | | | | | | | Problem appears to have been present since day one but masked because alignment aborts were not enabled. ca4b55800ed7 "arm, arm926ejs: always do cpu critical inits" turned on alignment aborts and uncovered this latent problem. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-By: Jason Cooper <u-boot@lakedaemon.net> Tested-By: Holger Brunck <holger.brunck@keymile.com> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-10-28-0/+5
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: ARM: Add Calxeda Highbank platform dkb: make mmc command as default enabled Marvell: dkb: add mmc support ARM: pantheon: add mmc definition davinci: remove config.mk file from the sources ARM:AM33XX: Add support for TI AM335X EVM ARM:AM33XX: Added timer support ARM:AM33XX: Add emif/ddr support ARM:AM33XX: Add clock definitions ARM:AM33XX: Added support for AM33xx omap3/emif4: fix registers definition davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM davinci: emac: add support for more than 1 PHYs davinci: emac: add new features to autonegotiate for EMAC da850evm: Move LPSC configuration to board_early_init_f() omap4_panda: Build in cmd_gpio support on panda omap: Don't use gpio_free to change direction to input mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset OMAP3: overo : Add environment variable optargs to bootargs OMAP3: overo: Move ethernet CS4 configuration to execute based on board id OMAP3: overo : Use ttyO2 instead of ttyS2. da830: add support for NAND boot mode dm36x: revert cache disable patch dm644X: revert cache disable patch devkit8000: Add malloc space omap: spl: fix build break due to changes in FAT OMAP3 SPL: Provide weak omap_rev_string omap: beagle: Use ubifs instead of jffs2 for nand boot omap: overo: Disable pull-ups on camera PCLK, HS and VS signals omap: overo: Configure mux for gpio10 SPL: Add DMA library omap3: Add interface for omap3 DMA omap3: Add DMA register accessors omap3: Add Base register for DMA arm, davinci: add missing LSPC define for MMC/SD1 U-Boot/SPL: omap4: Make ddr pre-calculated timings as default. DaVinci: correct MDSTAT.STATE mask omap4: splitting padconfs into common, 4430 and 4460 omap4: adding revision detection for 4460 ES1.1 omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL gplug: fixed build error as a result of code cleanup patch kirkwood_spi: add dummy spi_init() gpio: mvmfp: reduce include platform file ARM: orion5x: reduce dependence of including platform file serial: reduce include platform file for marvell chip ARM: kirkwood: reduce dependence of including platform file ARM: armada100: reduce dependence of including platform file ARM: pantheon: reduce dependence of including platform file Armada100: Add env storage support for Marvell gplugD Armada100: Add SPI flash support for Marvell gplugD Armada100: Add SPI support for Marvell gplugD SPI: Add SPI driver support for Marvell Armada100 dreamplug: initial board support. imx: fix coding style misc: pmic: drop old Freescale's pmic driver MX31: mx31pdk: use new pmic driver MX31: mx31ads: use new pmic driver MX31: mx31_litekit: use new pmic driver MX5: mx53evk: use new pmic driver MX5: mx51evk: use new pmic driver MX35: mx35pdk: use new pmic driver misc: pmic: addI2C support to pmic_fsl driver misc: pmic: use I2C_SET_BUS in pmic I2C MX5: efikamx/efikasb: use new pmic driver MX3: qong: use new pmic driver RTC: Switch mc13783 to generic pmic code MX5: vision2: use new pmic driver misc: pmic: Freescale PMIC switches to generic PMIC driver misc:pmic:samsung Enable PMIC driver at GONI target misc:pmic:max8998 MAX8998 support at a new PMIC driver. misc:pmic:core New generic PMIC driver mx31pdk: Remove unneeded config mx31: provide readable WEIM CS accessor MX51: vision2: Set global macros I2C: Add i2c_get/set_speed() to mxc_i2c.c ARM: Update mach-types devkit8000: Add config to enable SPL MMC boot devkit8000: protect board_mmc_init arm, post: add missing post_time_ms for arm cosmetic, post: Codingstyle cleanup arm, logbuffer: make it compileclean tegra2: Enable MMC for Seaboard tegra2: Add more pinmux functions tegra2: Rename PIN_ to PINGRP_ tegra2: Add more clock functions tegra2: Clean up board code a little tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
| * kirkwood_spi: add dummy spi_init()Michael Walle2011-10-27-0/+4
| | | | | | | | | | | | The spi_init() function is missing. Add it. Signed-off-by: Michael Walle <michael@walle.cc>
| * ARM: kirkwood: reduce dependence of including platform fileLei Wen2011-10-27-0/+1
| | | | | | | | | | | | | | | | | | | | | | For files like the drivers/serial/serial.c, it must include the platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the definition in the platform definition files. Include the platform definition file in the config file, so that it would decouple the dependence for the driver files. Signed-off-by: Lei Wen <leiwen@marvell.com>
* | GCC4.6: Squash warnings in kirkwood_spi.cMarek Vasut2011-10-27-2/+2
|/ | | | | | | | | | | | | | kirkwood_spi.c:125:2: warning: format '%08X' expects type 'unsigned int', but argument 4 has type 'const void *' kirkwood_spi.c:125:2: warning: format '%08X' expects type 'unsigned int', but argument 5 has type 'void *' kirkwood_spi.c:160:5: warning: format '%08x' expects type 'unsigned int', but argument 2 has type 'void *' Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Mike Frysinger <vapier@gentoo.org>
* spi: Add Marvell Kirkwood SPI driverPrafulla Wadaskar2009-06-26-0/+185
This patch adds a SPI driver for the Marvell Kirkwood SoC's. Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>