summaryrefslogtreecommitdiff
path: root/drivers/qe/uec_phy.c
Commit message (Collapse)AuthorAgeLines
* Change UEC PHY interface to RGMII on MPC8568MDSHaiying Wang2008-10-18-0/+24
| | | | | | | | | | | | | | Change UEC phy interface from GMII to RGMII on MPC8568MDS board Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed, but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable. Now both UEC1 and UEC2 can work properly under u-boot. It is also in consistent with the kernel setting for 8568 UEC phy interface. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* drivers/qe: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2008-08-13-3/+0
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* uec: add support for Broadcom BCM5481 Gigabit PHYAnton Vorontsov2008-03-25-0/+41
| | | | | | | | | This patch adds basic support for Broadcom BCM5481 PHY. RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is Peter Barada <peterb@logicpd.com>. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* uec: add support for gbit mii status readingsAnton Vorontsov2008-03-25-9/+19
| | | | Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* net: uec_phy: actually increment the timeout counterKim Phillips2008-03-07-1/+2
| | | | | | | | allow u-boot to recover (and, e.g., switch to another interface) in the case where a PHY does not report autonegotiation is complete within its two second timeout value. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* net: uec_phy: handle 88e1111 rev.B2 erratum 5.6Kim Phillips2008-03-02-0/+8
| | | | | | | | | | erratum 5.6 states the autoneg completion bit is functional only if the autoneg bit is asserted. This fixes any secondarily-issued networking commands on non-gigabit links on the mpc8360 mds board. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Remove annoying debug printout for PHY less boards.Joakim Tjernlund2008-01-16-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | PHY less board prints out lots of "read wrong ...": read wrong value : mii_id 3,mii_reg 2, base e0102320 read wrong value : mii_id 3,mii_reg 3, base e0102320 UEC: PHY is Generic MII (ffffffff) read wrong value : mii_id 3,mii_reg 4, base e0102320 read wrong value : mii_id 3,mii_reg 0, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 FSL UEC0: Full Duplex FSL UEC0: Speed 100BT FSL UEC0: Link is up Using FSL UEC0 device Make this printout depend on UEC_VERBOSE_DEBUG and remove its definition in uec_phy.c Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: reduce boot latency on QE UEC based boardsKim Phillips2008-01-16-22/+36
| | | | | | | | | | | | | | | actually polling for PHY autonegotiation to finish enables us to remove the 5 second boot prompt latency present on QE based boards. call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait code shamelessly stolen from tsec driver. also rm unused CONFIG_RMII_MODE code. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Add support for UEC to 8568Andy Fleming2007-08-14-7/+7
| | | | | Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Code cleanup.Wolfgang Denk2006-11-30-421/+424
|
* mpc83xx: add QE ethernet supportDave Liu2006-11-03-0/+604
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
generated by cgit v1.1 at 2024-11-01 16:36:20 +0000