summaryrefslogtreecommitdiff
path: root/drivers/power/twl6030.c
Commit message (Collapse)AuthorAgeLines
* power: twl6030: Power off supportPaul Kocialkowski2016-03-15-0/+8
| | | | | | This adds support for powering off (the omap SoC) from the twl6030. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* power: twl6030: Remove ifdef around the codePaul Kocialkowski2016-03-15-2/+0
| | | | | | | The TWL6030 power driver is only built when CONFIG_TWL6030_POWER is selected, thus there is no reason to wrap the code with ifdef. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* power: twl6030: Clear VUSB_IN_PMID bit on USB device setupPaul Kocialkowski2016-03-15-0/+1
| | | | | | | | | | | | When booting from USB, the bootrom sets the VUSB_IN_PMID bit of the MISC2 register of the TWL6030. However, U-Boot sets the VUSB_IN_VSYS bit to enable VBUS input. As both bits are contradictory, enabling both disables the input, according to the TWL6030 TRM. Thus, we need to clear the VUSB_IN_PMID bit in case of an USB boot (which could just as well be a memory boot after USB timed out). Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* power: twl6030: Configure VUSB voltage on USB device setupPaul Kocialkowski2016-03-15-0/+4
| | | | | | This explicitly sets VUSB voltage to 3.3V when enabling USB. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* power: twl6030: Device-index-specific MMC power initializationPaul Kocialkowski2016-03-15-24/+26
| | | | | | | | Not every device has multiple MMC slots available, so it makes sense to enable only the required LDOs for the available slots. Generic code in omap_hsmmc will enable both VMMC and VAUX1, in doubt. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* power: twl6030: Enable VAUX1 for eMMC power, depending on BOOT2 valuePaul Kocialkowski2016-03-15-0/+19
| | | | | | | | | | | This enables the VAUX1 supply, used for eMMC power in standard configurations. Its voltage is determined by the value of the BOOT2 pin of the TWL6030. Note that the TWL6030 might already have enabled this regulator at startup (depending on the value of the BOOT3 pin of the TWL6030), according to the TWL6030 datasheet. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* power: twl6030: Some more explicit registers and values definitionsPaul Kocialkowski2016-03-15-11/+15
| | | | | | | This makes the twl6030 mmc and usb-related power registers and values definitions more explicit and clear and adds prefixes to them. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* ARMV7: OMAP4: Add twl6032 supportOleg Kosheliev2013-12-04-6/+48
| | | | | | | | | | Added chip type detection and twl6032 support in the battery control and charge functions. Based on Balaji T K <balajitk@ti.com> patches for TI u-boot. Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
* ARMV7: OMAP4: Add struct for twl603x dataOleg Kosheliev2013-12-04-5/+20
| | | | | | | | | | | | | The data struct is used to support different PMIC chip types. It contains the chip type and the data (e.g. registers addresses, adc multiplier) which is different for twl6030 and twl6032. Replaced some hardcoded values with the structure vars. Based on Balaji T K <balajitk@ti.com> patches for TI u-boot. Signed-off-by: Oleg Kosheliev <oleg.kosheliev@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* twl6030: move twl6030 register access functions to common header fileNishanth Menon2013-05-10-11/+0
| | | | | | | | twl6030_i2c_[read|write]_u8 can be used else where to access multi-function device such as twl6030, so move the register access functions to the common twl6030.h header file. Signed-off-by: Nishanth Menon <nm@ti.com>
* twl6030: twl6030_i2c_[read|write]_u8 prototype consistentNishanth Menon2013-05-10-34/+34
| | | | | | | | | | | | | | | u-boot standard i2c register access prototype is i2c_read(addr, reg, 1, &buf, 1) i2c_reg_write(u8 addr, u8 reg, u8 val) twl6030_i2c_read_u8(u8 addr, u8 *val, u8 reg) twl6030_i2c_write_u8(u8 addr, u8 val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl6030_i2c_read_u8(u8 addr, u8 reg, u8 *val) twl6030_i2c_write_u8(u8 addr, u8 reg, u8 val) Signed-off-by: Nishanth Menon <nm@ti.com>
* mmc: omap: config VMMC, MMC1_PBIASBalaji T K2011-09-30-0/+7
| | | | | | | | | | Config VMMC voltage to 3V for MMC/SD card slot and PBIAS settings needed for OMAP4 Fixes MMC/SD detection on boot from eMMC. Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARMV7: OMAP4: twl6030 add battery charging supportBalaji T K2010-12-11-2/+122
| | | | | | | | | | Add battery charging support twl6030 driver. Add support for battery voltage and current measurements. Add command to get battery status and start/stop battery charging from USB. Signed-off-by: Balaji T K <balajitk@ti.com> Tested-by: Steve Sakoman <steve.sakoman@linaro.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* ARMV7: Add support for the TWL6030 I2C power chip used in OMAP4 systemsSteve Sakoman2010-08-05-0/+78
This patch add the basic infrastructure for the TWL6030 driver and enables support in the two existing OMAP4 boards, Panda and OMAP4430 SDP Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit v1.1 at 2024-11-20 10:27:12 +0000