summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/uniphier
Commit message (Collapse)AuthorAgeLines
* pinctrl: uniphier: add UniPhier sLD3 pinctrl driverMasahiro Yamada2016-09-18-0/+135
| | | | | | Add pin-mux support for UniPhier sLD3 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: support 4bit-width pin-mux register capabilityMasahiro Yamada2016-09-18-14/+11
| | | | | | | On LD4 SoC or later, the pin-mux registers are 8bit wide, while 4bit wide on sLD3 SoC. Support it for the sLD3 pinctrl driver. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: move register base macros from header to .c fileMasahiro Yamada2016-09-14-4/+4
| | | | | | | These macros are only referenced in pinctrl-uniphier-core.c, so they need not reside in a header file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add System Bus pin-mux settingsMasahiro Yamada2016-09-14-0/+147
| | | | | | This is needed to get access to UniPhier System Bus (external bus). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: use (devm_)ioremap() instead of map_sysmem()Masahiro Yamada2016-07-24-30/+17
| | | | | | | | This does not have much impact on behavior, but makes code look more more like Linux. The use of devm_ioremap() often helps to delete .remove callbacks entirely. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add Ethernet pin-mux settingsMasahiro Yamada2016-07-02-0/+94
| | | | Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: avoid building unneeded pin-mux tables for SPLMasahiro Yamada2016-07-02-171/+192
| | | | | | | SPL does not use all of the devices, so we can save some memory footprint. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: support pin configuration for dedicated pinsMasahiro Yamada2016-07-02-154/+149
| | | | | | | | | | | | | | PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration (pin biasing, drive strength control), but not pin-muxing. Allow to fill the mux value table with -1 for those pins; pins with mux value -1 will be skipped in the pin-mux set function. The mux value type should be changed from "unsigned" to "int" in order to accommodate -1 as a special case. [ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20Masahiro Yamada2016-07-02-8/+118
| | | | | | | | | | | PH1-LD11 and PH1-LD20 have much pin controlling in common, so I added a single driver shared between them in the initial commit. However, the Ethernet pin-mux settings I am going to add are different with each other, and they may diverge more as the progress of development. Split it into two dedicated drivers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: allow to have pinctrl node under syscon nodeMasahiro Yamada2016-07-02-12/+12
| | | | | | | | | | | Currently, the UniPhier pinctrl driver itself is a syscon, but it turned out much more reasonable to make it a child node of a syscon because our syscon node consists of a bunch of system configuration registers, not only pinctrl, but also phy, and misc registers. It is difficult to split the node. This commit allows to migrate to the new DT structure. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: remove unneeded pin group nand_cs1Masahiro Yamada2016-06-30-3/+0
| | | | | | | This SoC does not support NAND CS1. This place-holder is no longer necessary. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: fix NAND pin-mux setting for PH1-LD11/LD20Masahiro Yamada2016-06-30-2/+2
| | | | | | My mistake in the initial support patch. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: remove wrong pin-mux functions for ProXstream2Masahiro Yamada2016-06-30-2/+0
| | | | | | These are pin group names, not function names. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: fix NAND and SD pin-mux settings for PH1-LD11/LD20Masahiro Yamada2016-04-24-4/+4
| | | | | | | I found many mistakes in the initial version. Fixes: 8a3328c209d0 ("pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: rename function/array namesMasahiro Yamada2016-04-24-102/+102
| | | | | | Make function/array names match the file names for consistency. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: support UniPhier PH1-LD11 pinctrl driverMasahiro Yamada2016-04-01-6/+7
| | | | | | | | The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20 (as far as used in boot-loader), so this commit makes the driver shared between the two SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driverMasahiro Yamada2016-04-01-0/+120
| | | | | | Add pin configuration and pinmux support for UniPhier PH1-LD20 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: support per-pin input enable for new SoCsMasahiro Yamada2016-04-01-1/+28
| | | | | | | | Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input signal gating for each pin. (While, existing ones only support it per pin-group.) This commit prepares the core part for that. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: introduce capability flagMasahiro Yamada2016-04-01-27/+29
| | | | | | | | | | | | | | | | | | | | | The core part of the UniPhier pinctrl driver needs to support a new capability for upcoming UniPhier ARMv8 SoCs. This sometimes happens because pinctrl drivers include really SoC-specific stuff. This commit intends to tidy up SoC-specific parameters of the existing drivers before adding new ones. Having flags would be better than adding new members every time a new SoC-specific capability comes up. At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE. This capability (I'd say rather quirk) was added for PH1-Pro4 and PH1-Pro5 as requirement from our customer. For those SoCs, one pin-mux setting is controlled by the combination of two separate registers; the LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4). Because it is impossible to update two separate registers atomically, the LOAD_PINCTRL register should be set in order to make the pin-mux settings really effective. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: use devm_get_addr() to get base addressMasahiro Yamada2016-04-01-6/+3
| | | | | | | | | Currently, fdtdec_get_addr_size() does not support the address translation, so it cannot handle device trees with non-straight "ranges" properties. (This would be a problem with DTS for UniPhier ARMv8 SoCs.) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* ARM: uniphier: drop PH1- prefix from CONFIG options and file namesMasahiro Yamada2016-03-24-19/+19
| | | | | | | | The current CONFIG names like "CONFIG_ARCH_UNIPHIER_PH1_PRO4" is too long. It would not hurt to drop "PH1_" because "UNIPHIER_" already well specifies the SoC family. Also, rename files for consistency. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIERMasahiro Yamada2016-03-09-8/+8
| | | | | | | | | | CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER to guard the drivers/pinctrl/uniphier directory. The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long, so rename it into CONFIG_PINCTRL_UNIPHIER. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: set input-enable before pin-muxingMasahiro Yamada2016-03-09-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | While IECTRL is disabled, input signals are pulled-down internally. If pin-muxing is set up first, glitch signals (Low to High transition) might be input to hardware blocks. Bad case scenario: [1] The hardware block is already running before pinctrl is handled. (the reset is de-asserted by default or by a firmware, for example) [2] The pin-muxing is set up. The input signals to hardware block are pulled-down by the chip-internal biasing. [3] The pins are input-enabled. The signals from the board reach the hardware block. Actually, one invalid character is input to the UART blocks for such SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the power on reset. To avoid such problems, pins should be input-enabled before muxing. [ ported from Linux commit bac7f4c1bf5e7c6ccd5bb71edc015b26c77f7460 ] Fixes: 5dc626f83619 ("pinctrl: uniphier: add UniPhier pinctrl core support") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* bug.h: move BUILD_BUG_* defines to include/linux/bug.hMasahiro Yamada2016-01-25-3/+1
| | | | | | | | | | | | | | | | BUILD_BUG_* macros have been defined in several headers. It would be nice to collect them in include/linux/bug.h like Linux. This commit is cherry-picking useful macros from include/linux/bug.h of Linux 4.4. I did not import BUILD_BUG_ON_MSG() because it would not work if it is used with include/common.h in U-Boot. I'd like to postpone it until the root cause (the "error()" macro in include/common.h causes the name conflict with "__attribute__((error()))") is fixed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* Various Makefiles: Add SPDX-License-Identifier tagsTom Rini2015-11-10-0/+4
| | | | | | | | | | | After consulting with some of the SPDX team, the conclusion is that Makefiles are worth adding SPDX-License-Identifier tags too, and most of ours have one. This adds tags to ones that lack them and converts a few that had full (or in one case, very partial) license blobs into the equivalent tag. Cc: Kate Stewart <kstewart@linuxfoundation.org> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: uniphier: rename CONFIG_MACH_* to CONFIG_ARCH_UNIPHIER_*Masahiro Yamada2015-09-25-6/+6
| | | | | | | I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify they belong to UniPhier SoC family. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier PH1-LD6b pinctrl driverMasahiro Yamada2015-09-25-0/+140
| | | | | | Add pin configuration and pinmux support for UniPhier PH1-LD6b SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier ProXstream2 pinctrl driverMasahiro Yamada2015-09-25-0/+147
| | | | | | | Add pin configuration and pinmux support for UniPhier ProXstream2 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier PH1-Pro5 pinctrl driverMasahiro Yamada2015-09-25-0/+151
| | | | | | Add pin configuration and pinmux support for UniPhier PH1-Pro5 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier PH1-sLD8 pinctrl driverMasahiro Yamada2015-09-25-0/+148
| | | | | | Add pin configuration and pinmux support for UniPhier PH1-sLD8 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier PH1-Pro4 pinctrl driverMasahiro Yamada2015-09-25-0/+137
| | | | | | Add pin configuration and pinmux support for UniPhier PH1-Pro4 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier PH1-LD4 pinctrl driverMasahiro Yamada2015-09-25-0/+141
| | | | | | Add pin configuration and pinmux support for UniPhier PH1-LD4 SoC. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* pinctrl: uniphier: add UniPhier pinctrl core supportMasahiro Yamada2015-09-23-0/+274
The core support for the pinctrl drivers for all the UniPhier SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-11-02 05:00:53 +0000