summaryrefslogtreecommitdiff
path: root/drivers/net
Commit message (Collapse)AuthorAgeLines
* ENGR00152241 MX6: enable 1G speed mode for PHY and ENETZeng Zhaoming2011-06-29-10/+41
| | | | | | | | | | | | | In precode, PHY forced to work at 100M even connect to 1G switch. In this commit, let PHY auto negotiate it working speed. Enet tx work at store-and-forward mode. BTW, AR8031 take quite a long time, about 1.6s from negotiation to link up. we have to wait and then set ENET correctly. Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
* ENGR00139198: iMX61 uBoot add ENET supportZeng Zhaoming2011-06-27-5/+69
| | | | | | | | | | | | | | | | Add ENET and AR8031 PHY support to uboot. To make it works on sabreauto, need do following changes: 1. rework phy to output 125M clock from CLK_25M signal, and the 125M clock input to SoC as reference clock to generate RGMII_TXC clock. 2. Enable TXC delay in PHY debug register. 3. set ENET working in RMII mode. 4. set ENET working at 1000M or 100M/10M. 5. set ENET TX fifo to maximum to avoid underrun error. 6. force AR8031 PHY working at 100M Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
* ENGR00137713 MX53 Uboot SMSC Fix order in which mac addr bytes are read from IIMAnish Trivedi2011-01-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Given that an example mac addr is 00-11-22-33-44-55, it should be fused into the IIM at the following locations: 0xC24 - 00 0xC28 - 11 0xC2C - 22 0xC30 - 33 0xC34 - 44 0xC38 - 55 Then, when reading the bytes into a mac array, it should be read as follows: mac[0] - 00 mac[1] - 11 mac[2] - 22 mac[3] - 33 mac[4] - 44 mac[5] - 55 Previously, it was read into the array in reverse order. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00137596 MX53 Uboot SMC911X driver needs to get mac addr from IIMAnish Trivedi2011-01-05-0/+25
| | | | | | | If the MAC addr read from the controller's ADDRH and ADDRL registers is invalid, then try to read MAC address programmed in MX53's IIM. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00123924: Reconstructure fuse files and add fuse to mx53.Terry Lv2010-07-16-19/+40
| | | | | | | | | | 1. Reconstructure fuse. Move fuse files to common directory. 2. Read mac from fuse in fec. 3. Remove scc and srk command from fuse command. 4. Change fuse to iim. 5. Add fuse for mx53. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00122651: Add dwc_ahsata supportTerry Lv2010-06-24-15/+17
| | | | | | Add dwc_ahsata support. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00121832: Some code reconstructure for u-bootTerry Lv2010-03-22-3/+3
| | | | | | | | 1. Remove board specific code in mxc_i2c.c. 2. Remove board specific code in mxc_fec.c. 3. Move imx_spi_nor.h to include/asm-arm. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00121202 Add uboot support for MX53Jason2010-03-17-1/+4
| | | | | | Add uboot support for MX53 Signed-off-by:Jason Liu <r64343@freescale.com>
* ENGR000121601: FEC not work in mx28 u-bootTerry Lv2010-03-16-1/+10
| | | | | | FEC not work in mx28 u-boot. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00121379: MX28 U-BOOT enhancementsTerry Lv2010-03-12-743/+29
| | | | | | MX28 U-BOOT enhancements. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00120520: Enable MMU for mx51 and mx35Terry Lv2010-03-04-19/+110
| | | | | | | MMU enable code is missed in mx51 and mx35 u-boot. So add these codes. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00120476: Add fuse support for mx51Terry Lv2010-01-27-0/+4
| | | | | | Add fuse support for mx51. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00120206 iMX28 Enable Ethernet and MMC boot supportrel_imx_2.6.31_10.02.00Frank Li2010-01-25-0/+743
| | | | | | Enable Ethernet and MMC boot support for imx28-evk Signed-off-by: Frank Li <frank.li@freescale.com>
* ENGR00119890: Set right mac addr to FEC register in initTerry Lv2010-01-11-8/+11
| | | | | | | The mac addr set to FEC is smc911x's. So add a environment "fec_addr" to set fec address. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00118998: Can not get ip address when kernel boot upTerry Lv2009-12-11-0/+12
| | | | | | Kernel need uboot to set fec mac address. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00118647 Fix smc911x receive packet length not set correctlySammy He2009-11-20-1/+1
| | | | | | | Fix smc911x receive packet length not set correctly issue. This caused MX25 tftp timeout sometimes. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00118576 MX25: Support Smc911x ethernetSammy He2009-11-20-1/+15
| | | | | | | 1. Add imx cspi support for cpld access. 2. Add smc911x ethernet support from cpld. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00118428 MX233 Uboot: reslove the build error for branch imx_v2009.08Lionel Xu2009-11-13-4/+7
| | | | | | | bd->bi_enetaddr was removed in one of the previous patchs, some changes must be done to avoid building error. Signed-off-by: Lionel Xu <r63889@freescale.com>
* u-boot v2009.08 sd/mmc support.Terry Lv2009-11-03-458/+17
| | | | Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00116472-1 U-BOOT upgrade to V2009.08Fred Fan2009-09-14-2/+2
| | | | | | | | | | U-BOOT upgrade from V2009.01 to V2009.08 Initial version for i.MX51 BBG board. Support: FEC, SPI, spi Nor Flash Boot from spi nor flash and mmc/sd Signed-off-by:Fred Fan <r01011@freescale.com>
* ENGR00113941 MX233: Make UBOOT v2009.01 work on EVK boardLionel Xu2009-09-10-1/+1014
| | | | | | | | Porting MX233 UBOOT from 1.3.3 to V2009.01. Clear old cfg macro, such as CFG_HZ. Change MAC address getting source from initial configuration to On-Chip OTP. Signed-off-by: Lionel Xu <r63889@freescale.com>
* ENGR00113611: Add FEC support for BBG2.Terry Lv2009-09-10-6/+7
| | | | | | Add FEC support for BBG2. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00108673 Add i.MX25 core to U-BootAlan Carvalho de Assis2009-09-10-0/+40
| | | | | | This patch add support on U-Boot to i.MX25 processor. Signed-off-by: Alan Carvalho de Assis <alan.assis@freescale.com>
* ENGR00108473 Porting i.MX51 3stack TO2 support to V2009.01Fred Fan2009-09-10-0/+8
| | | | | | | Support i.MX51 TO2.0 3stack board. And enable LAN9217 support. NAND is not supported in this patch. Signed-off-by: Fred Fan <r01011@freescale.com>
* ENGR00107886 Porting MX31, MX35 3stack to u-boot V2009.01Fred Fan2009-09-10-2/+0
| | | | | | Modify and Verfiy MX31 & MX35 3stack according to the changes in V2009.01 Signed-off-by: Fred Fan <r01011@freescale.com>
* ENGR00104583 MX35 can not boot up kernelFred Fan2009-09-10-0/+2
| | | | | | | | uboot can not boot kernel. There are no more messages excepts uncompression message. The root cause is wrong romfile version offset. Signed-off-by: Fred Fan <r01011@freescale.com>
* ENGR00081147 Support i.MX35 3stack boardFred Fan2009-09-09-2/+1176
| | | | | | | | Support boot from NOR flash Support Multiple ethernet:LAN9217 and FEC Support upgrade u-boot Signed-off-by: Fred Fan <r01011@freescale.com>
* tsec: Wait for auto-negotiation to complete without linkPeter Tyser2009-08-21-10/+9
| | | | | | | | | | | | | | | | | | | | | Previously, waiting for auto-negotiation would only occur if a valid link had been detected. Problems arose when attempting to use a tsec immediately after bootup but before link was achieved, eg: => dhcp Auto-neg error, defaulting to 10BT/HD eTSEC1: No link. Auto-neg error, defaulting to 10BT/HD eTSEC2: No link. => With this patch applied the same operation as above resulted in: => dhcp Waiting for PHY auto negotiation to complete. done Enet starting in 1000BT/FD Speed: 1000, full duplex Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm: kirkwood: See to it that sent data is 8-byte alignedSimon Kagstrom2009-08-21-4/+18
| | | | | | | | | | U-boot might use non-8-byte-aligned addresses for sending data, which the kwgbe_send doesn't accept (bootp does this for me). This patch copies the data to be sent to a malloced temporary buffer if it is non-aligned. Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Wait for the link to come up on kirkwood network initSimon Kagstrom2009-08-21-6/+14
| | | | | | | | | | This patch makes the device wait for up to 5 seconds for the link to come up, similar to what many of the other network drivers do. This avoids confusing situations where, e.g., a tftp fails when initiated early after U-boot has started (before the link has come up). Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm:kirkwood Define kirkwood phy address magic numberSimon Kagstrom2009-08-21-4/+10
| | | | | Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* e1000: fix PCI memory addressingTimur Tabi2009-08-21-8/+9
| | | | | | | | | | | The Intel E1000 driver was making assumptions about the relationship between some virtual, physical, and PCI addresses. Also fix some bad usage of the DEBUGOUT macro Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: kirkwood: updates: used eth_setenv_enetaddr apiPrafulla Wadaskar2009-08-10-6/+9
| | | | | | | | | | | eth_setenv_enetaddr is avaible by upper layer using this saves 204 bytes on total image size used Local OUI instead of Marvell OUI for random MAC address generation logic Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Fix E1000 build warning on AP1000 boardRoy Zang2009-08-10-44/+44
| | | | | | | | | | Fix E1000 build warning on AP1000 board Fix the build warning on AP1000 board: e1000.c:131: warning: 'e1000_read_eeprom' used but never defined e1000.c:2012: warning: 'e1000_set_phy_mode' defined but not used Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: phy: bugfixes: mv88E61xx compiler warnings fixedPrafulla Wadaskar2009-08-10-9/+14
| | | | | | | | | | 1. mv88E61xx driver compiler warnings fixed 2. idstr if-else statements changed to switch() construct and added default case too. This fixed idstr may be uninitialized warning Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm: A320: driver for FTMAC100 ethernet controllerPo-Yu Chuang2009-08-10-0/+433
| | | | | | | This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Dual-license IBM code contributionsJosh Boyer2009-08-09-0/+2
| | | | | | | | | | | | | It was brought to our attention that U-Boot contains code derived from the IBM OpenBIOS source code originally provided with some of the older PowerPC 4xx development boards. As a result, the original license of this code has been carried in the various files for a number of years in the U-Boot project. IBM is dual-licensing the IBM code contributions already present in U-Boot under either the terms of the GNU General Public License version 2, or the original code license already present. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* Add Intel E1000 PCIE card supportRoy Zang2009-08-08-491/+3444
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on Intel PRO/1000 Network Driver 7.3.20-k2 Add Intel E1000 PCIE card support. The following cards are added: INTEL_82571EB_COPPER INTEL_82571EB_FIBER, INTEL_82571EB_SERDES INTEL_82571EB_QUAD_COPPER INTEL_82571PT_QUAD_COPPER INTEL_82571EB_QUAD_FIBER INTEL_82571EB_QUAD_COPPER_LOWPROFILE INTEL_82571EB_SERDES_DUAL INTEL_82571EB_SERDES_QUAD INTEL_82572EI_COPPER INTEL_82572EI_FIBER INTEL_82572EI_SERDES INTEL_82572EI INTEL_82573E INTEL_82573E_IAMT INTEL_82573L INTEL_82546GB_QUAD_COPPER_KSP3 INTEL_80003ES2LAN_COPPER_DPT INTEL_80003ES2LAN_SERDES_DPT INTEL_80003ES2LAN_COPPER_SPT INTEL_80003ES2LAN_SERDES_SPT 82571EB_COPPER dual ports, 82572EI single port, 82572EI_COPPER single port PCIE cards and 82545EM_COPPER, 82541GI_LF pci cards are tested on both P2020 board and MPC8544DS board. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Update Freescale copyrights to remove "All Rights Reserved"Kumar Gala2009-07-29-2/+2
| | | | | | "All Rights Reserved" conflicts with the GPL. Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
* Coding Style cleanup; update CHANGELOG.Wolfgang Denk2009-07-23-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* unify HOST_CFLAGS and HOSTCFLAGSMike Frysinger2009-07-23-1/+1
| | | | | | | | The top build system sets up HOSTCFLAGS a bit and exports it, but other places use HOST_CFLAGS instead. Unify the two as HOSTCFLAGS so that the values stay in sync. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* fec_mxc: driver for FEC ethernet controller on i.MX27Ilya Yanok2009-07-22-0/+1047
| | | | | Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* ppc4xx: Fixed compilation warning in 4xx_enet.cAlessio Centazzo2009-07-22-2/+1
| | | | | | | | | | | | | | | | | | | This patch fixes a compilation warning for some Ethernet PHY-less PPC4xx platforms (440SPE based ones) and a potential compilation error for 440SP platforms (use of undefined 'ethgroup' variable). In the original code and in case of 440SPE platforms, 'ethgroup' is initialized to -1 and never modified. Later in the function, within an #ifdef statement, an 'if statement' executes code only if 'ethgroup' is set to 4, therefore it is harmless to avoid executing the 'if statement' by removing the CONFIG_440SPE from the affected #ifdefs. In case of 440SP platforms with on-board Ethernet PHY, 'ethgroup' is undefined but used (there are not such platforms in the repository yet). All other architectures are not affected by this change. Signed-off-by: Alessio Centazzo acpatin@yahoo.com Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: phy: bugfixes: mv88E61xx multichip addressing supportPrafulla Wadaskar2009-07-22-10/+10
| | | | | | | | | | | | | | | | | | With these fixes, this driver works properly for multi chip addressging mode Bugfixes: 1. Build error fixed for function mv88e61xx_busychk_multic-fixed 2. PHY dev address error detection- fixed 3. wrong busy bit was refered in function mv88e61xx_busychk -fixed 4. invalid data read ptr was refered for RD_PHY in case of multichip addressing mode -fixed The Multichip Address mode is tested with RD6281A board having MV88E6165 switch on it Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm: Kirkwood: Check the error summary bit for error detectionSimon Kagstrom2009-07-22-1/+4
| | | | | | | | | | | The Marvell documentation for the 88f6281 states that the error coding is only valid if the error summary and last frame bits in the transmit descriptor status field are set. This patch adds checks for these for transmit (I would get transmit errors on bootp with the current check, which I believe are spurious). Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm: Kirkwood: Fix compiler optimization bug for kwgbe_sendSimon Kagstrom2009-07-22-12/+19
| | | | | | | | | | | kwgbe_send/recv both have loops waiting for the hardware to set a bit. GCC 4.3.3 cleverly optimizes the send case to ... a while(1); loop. This patch uses readl to force a read from device memory. Other volatile accesses have also been replaced with readl/writel where appropriate (as per suggestions on the U-boot mailing list). Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* MIIPHYBB: Return 0xFFFF if the PHY is not asserting TA.Richard Retanubun2009-07-22-0/+7
| | | | | | | | | | | | This patch sets the returned value to 0xFFFF if the PHY does not exist and does not assert Transfer Acknowledge. A NULL check for the value pointer is also added for buffer overflow protection. Without this patch 'mii info' will show 'phantom' devices because the value will be not be initialized and return with some random value. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Convert SMC911X Ethernet driver to CONFIG_NET_MULTI APIBen Warren2009-07-22-160/+187
| | | | | | | | | | | | All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X* - cleaned up line lengths - modified all boards that override weak function in this driver - added Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Tested-by: Mike Frysinger <vapier@gentoo.org>
* P2020RDB Added support of Vitesse PHYs VSC8641(RGMII) and VSC8221(SGMII)Poonam Aggrwal2009-07-22-1/+51
| | | | | | | | | These PHYs are on P2020RDB platform. Also revamped Freescale copyright message in drivers/net/tsec.c. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: tsec - fix dereferencing type-punned pointer will break strict-aliasing ↵Kim Phillips2009-07-22-1/+4
| | | | | | | | | | | | rules warning fix this gcc 4.4 warning: tsec.c: In function 'tsec_init': tsec.c:200: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
generated by cgit v1.1 at 2024-12-28 22:17:14 +0000