summaryrefslogtreecommitdiff
path: root/drivers/net
Commit message (Collapse)AuthorAgeLines
* ENGR00176837-4 - FEC:enable some macro define for all chipFugang Duan2012-03-31-1/+1
| | | | | | | | | | | | | - Enable below macro define for all chip. Firstly, the marcos will be used in later version for later i.MX. Secondly, fix the build error in the former i.MX series chip before i.MX6. #define PHY_MIPSCR_LINK_UP (0x1 << 10) #define PHY_MIPSCR_SPEED_MASK (0x3 << 14) #define PHY_MIPSCR_1000M (0x2 << 14) #define PHY_MIPSCR_100M (0x1 << 14) #define PHY_MIPSCR_FULL_DUPLEX (0x1 << 13) Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00176837-3 - FEC : detect phy ID to match the phy type.Fugang Duan2012-03-22-55/+95
| | | | | | | | - Add phy id macro definitions. - Add mxc_get_phy_ouid helper function. - Use phy ouid to check the phy type. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00176834-2 - i.MX6DL sabresd: board bringupFugang Duan2012-03-20-2/+4
| | | | | | | | | | | | | The serial of patches adds the initial support for mx6dl sabra sd board: - DDR3 400MHz@64bit, 1G, 256M*4 - SD/MMC basic operations - Add PIN/IOMUX support for mmx6dl sabresd. - Ethernet is ok for 100/1000Mbps. - OTP fuse Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00176347-9 fec : increase wait time for phy linkFugang Duan2012-03-13-4/+7
| | | | | | | | | | | | | | - remove the excrescent code in enet_board_init function. - KSZ9021 phy auto-negotiation in mx6solo sabreauto RevA is used to establish link with the remote hub or switch. In general, the negotiation time is about 3-5 senconds But connecting to Gbps hub, the time is range from 8s to 15s. So, changing the MAX link waiting time to 20s. According to repetitious tests, solo ARD ethernet is ok in 100Mbps environment. It is not stable in 1000Mbps mode. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00174625: Remove build warnings for mx6qTerry Lv2012-02-17-1/+1
| | | | | | Remove build warnings for mx6q. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00173966-2: fec: add i.mx6dl supportJason Liu2012-02-07-5/+5
| | | | | | | This patch add i.mx6dl support for fec driver i.mx6dl and i.mx6dq shares the same ENET IP. Signed-off-by: Jason Liu <r64343@freescale.com>
* ENGR00172343 Add suport for i.MX 6Q Sabre Smart DeviceNancy Chen2012-01-24-3/+3
| | | | | | | | Add suport for i.MX 6Quad SABRE Smart Device. Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com> Signed-off-by: Tony Lin <tony.lin@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com>
* ENGR00171115 add fec support in mx6q sabreauto boardHake Huang2011-12-31-1/+1
| | | | | | | | | | Add fec support for sabreauto board Need hardware rework: 1. Add R450 10.0k 2. Remove R1105 1k 3. short Pin 1,2 of u516, will impact CAN1 Signed-off-by: Hake Huang <b20222@freescale.com>
* ENGR00169544 - FEC : fix "imx5x bootp command cannot work well".Fugang Duan2011-12-20-59/+55
| | | | | | | | | - "bootp" command sometime cannot work well in i.MX53 platform. - Cause: Phy detect cable link need some time, so need wait the complete of cable detect. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00163040 - FEC : Fix ethernet cannot work after system sleep.Fugang Duan2011-11-25-6/+26
| | | | | | | | | | | | - Descript: Ethernet can't work in uboot and kernel DHCP throught press 'reset' key when send sleep command 'echo mem > /sys/power/state' - Cause: FEC driver will power down phy when system sleep. If just reset the board, FEC driver cannot run resume function. So, need power on phy in uboot and linux driver. Signed-off-by: Fugang Duan <B38611@freescale.com>
* ENGR00161852: remove u-boot build warnings for mx6qTerry Lv2011-11-10-0/+2
| | | | | | Remove u-boot build warnings for mx6q. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00161004 MX6Q Uboot Rename sabreauto to arm2 boardAnish Trivedi2011-10-28-2/+2
| | | | | | | | | Sabreauto is an inaccurate name for the Armadillo2 board that this code is actually meant for. So, replaced "sabreauto" in folder names, file names, configs, and code with "arm2". Created a new machine id for ARM2 board. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00160399 Added support for the MX6Q Sabre-lite boardMahesh Mahadevan2011-10-25-29/+36
| | | | | | Includes support for uSDHC read, write, FEC, SPI-NOR etc. Signed-off-by: Mahesh Mahadevan <r9aadq@freescale.com>
* ENGR00152241 MX6: enable 1G speed mode for PHY and ENETZeng Zhaoming2011-06-29-10/+41
| | | | | | | | | | | | | In precode, PHY forced to work at 100M even connect to 1G switch. In this commit, let PHY auto negotiate it working speed. Enet tx work at store-and-forward mode. BTW, AR8031 take quite a long time, about 1.6s from negotiation to link up. we have to wait and then set ENET correctly. Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
* ENGR00139198: iMX61 uBoot add ENET supportZeng Zhaoming2011-06-27-5/+69
| | | | | | | | | | | | | | | | Add ENET and AR8031 PHY support to uboot. To make it works on sabreauto, need do following changes: 1. rework phy to output 125M clock from CLK_25M signal, and the 125M clock input to SoC as reference clock to generate RGMII_TXC clock. 2. Enable TXC delay in PHY debug register. 3. set ENET working in RMII mode. 4. set ENET working at 1000M or 100M/10M. 5. set ENET TX fifo to maximum to avoid underrun error. 6. force AR8031 PHY working at 100M Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Zeng Zhaoming <b32542@freescale.com>
* ENGR00137713 MX53 Uboot SMSC Fix order in which mac addr bytes are read from IIMAnish Trivedi2011-01-07-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Given that an example mac addr is 00-11-22-33-44-55, it should be fused into the IIM at the following locations: 0xC24 - 00 0xC28 - 11 0xC2C - 22 0xC30 - 33 0xC34 - 44 0xC38 - 55 Then, when reading the bytes into a mac array, it should be read as follows: mac[0] - 00 mac[1] - 11 mac[2] - 22 mac[3] - 33 mac[4] - 44 mac[5] - 55 Previously, it was read into the array in reverse order. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00137596 MX53 Uboot SMC911X driver needs to get mac addr from IIMAnish Trivedi2011-01-05-0/+25
| | | | | | | If the MAC addr read from the controller's ADDRH and ADDRL registers is invalid, then try to read MAC address programmed in MX53's IIM. Signed-off-by: Anish Trivedi <anish@freescale.com>
* ENGR00123924: Reconstructure fuse files and add fuse to mx53.Terry Lv2010-07-16-19/+40
| | | | | | | | | | 1. Reconstructure fuse. Move fuse files to common directory. 2. Read mac from fuse in fec. 3. Remove scc and srk command from fuse command. 4. Change fuse to iim. 5. Add fuse for mx53. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00122651: Add dwc_ahsata supportTerry Lv2010-06-24-15/+17
| | | | | | Add dwc_ahsata support. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00121832: Some code reconstructure for u-bootTerry Lv2010-03-22-3/+3
| | | | | | | | 1. Remove board specific code in mxc_i2c.c. 2. Remove board specific code in mxc_fec.c. 3. Move imx_spi_nor.h to include/asm-arm. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00121202 Add uboot support for MX53Jason2010-03-17-1/+4
| | | | | | Add uboot support for MX53 Signed-off-by:Jason Liu <r64343@freescale.com>
* ENGR000121601: FEC not work in mx28 u-bootTerry Lv2010-03-16-1/+10
| | | | | | FEC not work in mx28 u-boot. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00121379: MX28 U-BOOT enhancementsTerry Lv2010-03-12-743/+29
| | | | | | MX28 U-BOOT enhancements. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00120520: Enable MMU for mx51 and mx35Terry Lv2010-03-04-19/+110
| | | | | | | MMU enable code is missed in mx51 and mx35 u-boot. So add these codes. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00120476: Add fuse support for mx51Terry Lv2010-01-27-0/+4
| | | | | | Add fuse support for mx51. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00120206 iMX28 Enable Ethernet and MMC boot supportrel_imx_2.6.31_10.02.00Frank Li2010-01-25-0/+743
| | | | | | Enable Ethernet and MMC boot support for imx28-evk Signed-off-by: Frank Li <frank.li@freescale.com>
* ENGR00119890: Set right mac addr to FEC register in initTerry Lv2010-01-11-8/+11
| | | | | | | The mac addr set to FEC is smc911x's. So add a environment "fec_addr" to set fec address. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00118998: Can not get ip address when kernel boot upTerry Lv2009-12-11-0/+12
| | | | | | Kernel need uboot to set fec mac address. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00118647 Fix smc911x receive packet length not set correctlySammy He2009-11-20-1/+1
| | | | | | | Fix smc911x receive packet length not set correctly issue. This caused MX25 tftp timeout sometimes. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00118576 MX25: Support Smc911x ethernetSammy He2009-11-20-1/+15
| | | | | | | 1. Add imx cspi support for cpld access. 2. Add smc911x ethernet support from cpld. Signed-off-by: Sammy He <r62914@freescale.com>
* ENGR00118428 MX233 Uboot: reslove the build error for branch imx_v2009.08Lionel Xu2009-11-13-4/+7
| | | | | | | bd->bi_enetaddr was removed in one of the previous patchs, some changes must be done to avoid building error. Signed-off-by: Lionel Xu <r63889@freescale.com>
* u-boot v2009.08 sd/mmc support.Terry Lv2009-11-03-458/+17
| | | | Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00116472-1 U-BOOT upgrade to V2009.08Fred Fan2009-09-14-2/+2
| | | | | | | | | | U-BOOT upgrade from V2009.01 to V2009.08 Initial version for i.MX51 BBG board. Support: FEC, SPI, spi Nor Flash Boot from spi nor flash and mmc/sd Signed-off-by:Fred Fan <r01011@freescale.com>
* ENGR00113941 MX233: Make UBOOT v2009.01 work on EVK boardLionel Xu2009-09-10-1/+1014
| | | | | | | | Porting MX233 UBOOT from 1.3.3 to V2009.01. Clear old cfg macro, such as CFG_HZ. Change MAC address getting source from initial configuration to On-Chip OTP. Signed-off-by: Lionel Xu <r63889@freescale.com>
* ENGR00113611: Add FEC support for BBG2.Terry Lv2009-09-10-6/+7
| | | | | | Add FEC support for BBG2. Signed-off-by: Terry Lv <r65388@freescale.com>
* ENGR00108673 Add i.MX25 core to U-BootAlan Carvalho de Assis2009-09-10-0/+40
| | | | | | This patch add support on U-Boot to i.MX25 processor. Signed-off-by: Alan Carvalho de Assis <alan.assis@freescale.com>
* ENGR00108473 Porting i.MX51 3stack TO2 support to V2009.01Fred Fan2009-09-10-0/+8
| | | | | | | Support i.MX51 TO2.0 3stack board. And enable LAN9217 support. NAND is not supported in this patch. Signed-off-by: Fred Fan <r01011@freescale.com>
* ENGR00107886 Porting MX31, MX35 3stack to u-boot V2009.01Fred Fan2009-09-10-2/+0
| | | | | | Modify and Verfiy MX31 & MX35 3stack according to the changes in V2009.01 Signed-off-by: Fred Fan <r01011@freescale.com>
* ENGR00104583 MX35 can not boot up kernelFred Fan2009-09-10-0/+2
| | | | | | | | uboot can not boot kernel. There are no more messages excepts uncompression message. The root cause is wrong romfile version offset. Signed-off-by: Fred Fan <r01011@freescale.com>
* ENGR00081147 Support i.MX35 3stack boardFred Fan2009-09-09-2/+1176
| | | | | | | | Support boot from NOR flash Support Multiple ethernet:LAN9217 and FEC Support upgrade u-boot Signed-off-by: Fred Fan <r01011@freescale.com>
* tsec: Wait for auto-negotiation to complete without linkPeter Tyser2009-08-21-10/+9
| | | | | | | | | | | | | | | | | | | | | Previously, waiting for auto-negotiation would only occur if a valid link had been detected. Problems arose when attempting to use a tsec immediately after bootup but before link was achieved, eg: => dhcp Auto-neg error, defaulting to 10BT/HD eTSEC1: No link. Auto-neg error, defaulting to 10BT/HD eTSEC2: No link. => With this patch applied the same operation as above resulted in: => dhcp Waiting for PHY auto negotiation to complete. done Enet starting in 1000BT/FD Speed: 1000, full duplex Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm: kirkwood: See to it that sent data is 8-byte alignedSimon Kagstrom2009-08-21-4/+18
| | | | | | | | | | U-boot might use non-8-byte-aligned addresses for sending data, which the kwgbe_send doesn't accept (bootp does this for me). This patch copies the data to be sent to a malloced temporary buffer if it is non-aligned. Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Wait for the link to come up on kirkwood network initSimon Kagstrom2009-08-21-6/+14
| | | | | | | | | | This patch makes the device wait for up to 5 seconds for the link to come up, similar to what many of the other network drivers do. This avoids confusing situations where, e.g., a tftp fails when initiated early after U-boot has started (before the link has come up). Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm:kirkwood Define kirkwood phy address magic numberSimon Kagstrom2009-08-21-4/+10
| | | | | Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* e1000: fix PCI memory addressingTimur Tabi2009-08-21-8/+9
| | | | | | | | | | | The Intel E1000 driver was making assumptions about the relationship between some virtual, physical, and PCI addresses. Also fix some bad usage of the DEBUGOUT macro Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: kirkwood: updates: used eth_setenv_enetaddr apiPrafulla Wadaskar2009-08-10-6/+9
| | | | | | | | | | | eth_setenv_enetaddr is avaible by upper layer using this saves 204 bytes on total image size used Local OUI instead of Marvell OUI for random MAC address generation logic Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Fix E1000 build warning on AP1000 boardRoy Zang2009-08-10-44/+44
| | | | | | | | | | Fix E1000 build warning on AP1000 board Fix the build warning on AP1000 board: e1000.c:131: warning: 'e1000_read_eeprom' used but never defined e1000.c:2012: warning: 'e1000_set_phy_mode' defined but not used Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* net: phy: bugfixes: mv88E61xx compiler warnings fixedPrafulla Wadaskar2009-08-10-9/+14
| | | | | | | | | | 1. mv88E61xx driver compiler warnings fixed 2. idstr if-else statements changed to switch() construct and added default case too. This fixed idstr may be uninitialized warning Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* arm: A320: driver for FTMAC100 ethernet controllerPo-Yu Chuang2009-08-10-0/+433
| | | | | | | This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* Dual-license IBM code contributionsJosh Boyer2009-08-09-0/+2
| | | | | | | | | | | | | It was brought to our attention that U-Boot contains code derived from the IBM OpenBIOS source code originally provided with some of the older PowerPC 4xx development boards. As a result, the original license of this code has been carried in the various files for a number of years in the U-Boot project. IBM is dual-licensing the IBM code contributions already present in U-Boot under either the terms of the GNU General Public License version 2, or the original code license already present. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
generated by cgit v1.1 at 2024-11-25 13:05:06 +0000