summaryrefslogtreecommitdiff
path: root/drivers/mtd
Commit message (Collapse)AuthorAgeLines
...
* MTD: SPEAr SMI: Add write support for length < 4 bytesStefan Roese2012-07-07-4/+18
| | | | | | | | Needed for redundant environment for example. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com>
* st_smi: Fixed page size for Winbond W25Q128FV flashArmando Visconti2012-07-07-1/+1
| | | | | | Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change timeout loop implementationAmit Virdi2012-07-07-10/+17
| | | | | | | | | | | There are two problems in the current timeout loop implementation: 1. In case initial test failing, there will always be a delay of 1 ms 2. The delay duration is not tunable The new implementation addresses both these limitations. Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fix bug in flash_print_info()Armando Visconti2012-07-07-2/+7
| | | | | | | | | If the flash size was smaller than 1MB then flash_print_info() was erroneously reporting 0 MB. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change the flash probing methodArmando Visconti2012-07-07-27/+65
| | | | | | | | | | THis patch introduces a new methodology for flash probing in which flash_devices[] table, looked-up thru the dev_id, is used to locate the flash geometry and information. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Removed no needed dependency on ST_M25Pxx_IDArmando Visconti2012-07-07-32/+18
| | | | | | | | | | Since the smi erase code is very generic and works for any kind of flash, there is no need to test for ST_M25Pxx_ID flash types like m25p40 flashes). Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fix smi read statusVipin Kumar2012-07-07-6/+2
| | | | | | | | | | | | smi_read_sr fails sometimes because of TFF not getting set within assumed time. This condition may arise because of, for example, smi memory being in a erase mode. This fix is to enable reading the status register until timeout. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Move status register read before modifying ctrl registerShiraz Hashim2012-07-07-2/+4
| | | | | | Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Read status until timeout happensVipin KUMAR2012-07-07-1/+1
| | | | | | | | | SMI driver read status fails because the control register could not be overwritten. Instead, the read status should be tried until timeout. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Enhance the error handlingAmit Virdi2012-07-07-13/+21
| | | | | | | | | | | This commit does the following: - Reports error if SNOR flash is not found on the board - Changes smi_read_sr to return error using which a retry mechanism is implemented for reading flash status Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Return error in case TFF is not setAmit Virdi2012-07-07-8/+14
| | | | | | | | | | Curently the code makes wrong assumption that the Transfer finished flag shall be set within the stipulated time. However, there may occur a scenario in which the TFF flag is not set. Return error in that case. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Add support for SPEAr SMI driverVipin KUMAR2012-07-07-4/+5
| | | | | | | | | | | | | | SMI is the serial memory interface controller provided by ST. Earlier, a driver exists in the u-boot source code for the SMI IP. However, it was specific to spear platforms. This commit converts the same driver to a more generic driver. As a result, the driver files are renamed to st_smi.c and st_smi.h and moved into drivers/mtd folder for reusability by other platforms using smi controller peripheral. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* mtd/NAND: Remove obsolete SPEAr specific NAND driversVipin KUMAR2012-07-07-124/+0
| | | | | | | | | | | Since, SPEAr platform uses generic FSMC driver now, so spear specific files drivers/mtd/nand/spr_nand.c, arch/arm/include/asm/arch-spear/spr_nand.h are removed Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Scott Wood <scottwood@freescale.com>
* mtd/NAND: Add FSMC driver supportVipin KUMAR2012-07-07-0/+487
| | | | | | | | | | | | | | Flexible static memory controller is a peripheral provided by ST, which controls the access to NAND chips along with many other memory device chips eg NOR, SRAM. This patch adds the driver support for FSMC controller interfacing with NAND memory. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Scott Wood <scottwood@freescale.com>
* sf: winbond: Add support for the Winbond W25Q80BLStephen Warren2012-07-07-0/+8
| | | | | | | This chip is present on the Compulab TrimSlice. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk2012-05-20-14/+28
|\ | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-nand-flash: NAND: Remove ONFI detection message to from bootup log driver/mtd:IFC: Fix possible memory leak driver/mtd: IFC NAND: Add support of ONFI NAND flash mtd, nand: move some printfs to debug output. nand_util: correct YAFFS image write function powerpc/85xx: fix NAND boot linker scripts for -fpic nand: extend .raw accesses to work on multiple pages
| * NAND: Remove ONFI detection message to from bootup logStefan Roese2012-05-18-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Without this patch, boot shows this messages upon NAND detection: NAND: ONFI flash detected ONFI param page 0 valid ONFI flash detected ONFI param page 0 valid 128 MiB With this patch, its back to the U-Boot "standard": NAND: 128 MiB Tested on x600 (SPEAr600). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
| * driver/mtd:IFC: Fix possible memory leakPrabhakar Kushwaha2012-05-18-0/+1
| | | | | | | | | | | | | | if priv->bank >= MAX_BANK, priv should be freed before returning ENODEV. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
| * driver/mtd: IFC NAND: Add support of ONFI NAND flashPrabhakar Kushwaha2012-05-18-5/+16
| | | | | | | | | | | | | | | | | | - Fix NAND_CMD_READID command for ONFI detect. - Add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
| * mtd, nand: move some printfs to debug output.Heiko Schocher2012-05-18-6/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | current U-Boot shows on startup (for example on the enbw_cmc board) the following printfs from the nand subsystem: Flash: 2 MiB NAND: Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 nand_read_bbt: Bad block at 0x000002980000 nand_read_bbt: Bad block at 0x000003240000 128 MiB MMC: davinci: 0 remove them to debug output, so it shows with this patch: Flash: 2 MiB NAND: 128 MiB MMC: davinci: 0 Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
| * nand_util: correct YAFFS image write functionLiu, Wentao2012-05-18-1/+1
| | | | | | | | | | | | | | | | | | | | In function nand_write_skip_bad(),for YAFFS filesystem part, write_oob() will return 0 when success, so when rval equals 0, it should continue to write the next page, and no break. Signed-off-by: Wentao, Liu <wentao.liu@intel.com> Acked-by: Lei Wen <leiwen@marvell.com> Signed-off-by: Scott Wood <scott@tyr.buserror.net>
* | imx: nand: Support flash based BBTTimo Ketola2012-05-15-0/+33
|/ | | | | Signed-off-by: Timo Ketola <timo@exertus.fi> Acked-by: Scott Wood <scottwood@freescale.com>
* linux/compat.h: rename from linux/mtd/compat.hMike Frysinger2012-04-30-10/+10
| | | | | | This lets us use it in more places than just mtd code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* GCC4.6: Squash warnings in onenand_base.cWolfgang Denk2012-04-21-3/+2
| | | | | | | | | | | | Fix gcc 4.6 build warnings: onenand_base.c: In function 'onenand_probe': onenand_base.c:2577:6: warning: variable 'maf_id' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2012-04-16-2/+9
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: ARM926EJS: Fix cache.c to comply with checkpatch.pl ARM926EJS: Make asm routines volatile in cache ops MX35: mx35pdk: wrong board revision ARM1136: MX35: Make asm routines volatile in cache ops ARM: add u-boot.imx as target for i.MX SOCs M28: Pull out CONFIG_APBH_DMA so it's always enabled DMA: Split the APBH DMA init into block and channel init imx: Return gpio_set_value in gpio_direction_output imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5) imx: Add GPIO_TO_PORT macro in the mxc_gpio driver imx: Remove unneeded/repititive definitions from imx headers i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC MX31: mx31pdk: drop enable_caches from board file i.MX28: Fix initial stack pointer position mx35: mx35pdk: fix when cache functions are linked mx35: flea3: fix when cache functions are linked ARM: 926ejs: use debug() for misaligned addresses ARM1136: add cache flush and invalidate operations mx6qsabrelite: Fix the serial console port mx6qsabrelite: Add boot switch setting information into the README i.MX6: mx6qsabrelite: add cache commands if cache is enabled i.MX6: implement enable_caches() i.MX6: define CACHELINE_SIZE MX53: DDR: Fix ZQHWCTRL field TZQ_CS mx28evk: Add a README file mx28: Split the README into a common part and a m28 specific part tricorder: Load kernel from ubifs tricorder: Add UBIFS cm-t35: fix Ethernet reset timing hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT BeagleBoard: Remove userbutton command and use gpio command instead OMAP: Move omap1510inn to Unmaintained / Orphaned
| * DMA: Split the APBH DMA init into block and channel initMarek Vasut2012-04-16-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the issue where mxs_dma_init() was called either twice or never, without introducing any new init hooks. The idea is to allow each and every device using the APBH DMA block to configure and request only the channels it uses, instead of making it call init for all the channels as is now. The common DMA block init part, which only configures the block, is then called from CPUs arch_cpu_init() call. NOTE: This patch depends on: http://patchwork.ozlabs.org/patch/150957/ Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* | drivers/mtd/spr_smi.c: Fix build warningAnatolij Gustschin2012-04-14-5/+0
|/ | | | | | | | | | Fix: spr_smi.c: In function 'smi_write': spr_smi.c:325:15: warning: variable 'WM' set but not used [-Wunused-but-set-variable] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Vipin Kumar <vipin.kumar@st.com>
* onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()Lukasz Majewski2012-04-04-16/+29
| | | | | | | | | | | | | | | | | | This replacement causes 4KB page size devices to work properly with u-boot. The old ONENAND_IS_MLC() behavior has been preserved by explicit setting of ONENAND_HAS_4KB_PAGE for those devices. This change makes the onenand_base.c file more resembling the respective kernel sources. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> --- Test HW: - Samsung S5PC110 GONI - Samsung S5PC210 Universal
* onenand:samsung Target dependent OneNAND chip probe functionLukasz Majewski2012-04-04-7/+46
| | | | | | | | | | Separate callback for probing OneNAND memory chip. If no special function is defined, default implementation will be used. This approach gives more flexibility for OneNAND device probing. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* i.MX28: Add cache support to MXS NAND driverMarek Vasut2012-03-29-3/+50
| | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* NAND: TI: fix warnings in omap_gpmc.cStefano Babic2012-03-27-6/+8
| | | | | | | | | | | | | | The following warnings are reported for boards using SOFT ECC. omap_gpmc.c:33:30: warning: 'hw_nand_oob' defined but not used omap_gpmc.c:78:13: warning: 'omap_hwecc_init' defined but not used omap_gpmc.c:116:12: warning: 'omap_correct_data' defined but not used omap_gpmc.c:182:12: warning: 'omap_calculate_ecc' defined but not used omap_gpmc.c:208:13: warning: 'omap_enable_hwecc' defined but not used Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com>
* cfi: fix the incomplete erased status check in buffer writeTao Hou2012-03-21-2/+2
| | | | | | | | | | Without the fix, flash_write_cfibuffer will terminate the erased status check once an all-0xFF word has been found instead of continuing the erased status check utill the first non-0xFF word. Signed-off-by: Tao Hou <hotforest@gmail.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* mtd/nand:Fix wrong usage of is_blank() in fsl_ifc_run_commandPrabhakar Kushwaha2012-02-28-24/+28
| | | | | | | | | | | | | | Freescale IFC NAND Machine calculates ECC on 512byte sector and same is used in fsl_ifc_run_command() during ECC status verification. Also this sector is passed to is_blank() for blank checking. It is wrong at first place because is_blank()'s implementation checks for Page size and OOB area size. is_blank() should be called per page for main and OOB area verification. Variables name are redefined to avoid confusion between buffer and ecc sector. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* mtd/nand: Fix IFC driver to support 2K NAND pagePrabhakar Kushwaha2012-02-28-14/+13
| | | | | | | | | | | 1) OOB area should be updated irrespective of NAND page size. Earlier it was updated only for 512byte NAND page. 2) During OOB update fbcr should be equal to OOB size. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* nand: reinstate lazy bad block scanningScott Wood2012-02-28-3/+7
| | | | | | | | | | | | | commit 2a8e0fc8b3dc31a3c571e439fbf04b882c8986be ("nand: Merge changes from Linux nand driver") accidentally reverted commit 13f0fd94e3cae6f8a0d9fba5d367e311edc8ebde ("NAND: Scan bad blocks lazily."). Reinstate the change, as amended by commit ff49ea8977b56916edd5b1766d9939010e30b181 ("NAND: Mark the BBT as scanned prior to calling scan_bbt."). Signed-off-by: Scott Wood <scottwood@freescale.com>
* Revert "nand: make 1-bit software ECC configurable"Scott Wood2012-02-28-5/+1
| | | | | | | | | | | | | | This reverts commit 4fee6c2f295f932b8febdc7ce8731ba045695fa5. It breaks boards that currently rely on soft-ecc, as pointed out here: http://patchwork.ozlabs.org/patch/140872/ The reverted patch should be resubmitted with documentation, and with the CONFIG_MTD_ECC_SOFT selected from every board that needs it. We could start by looking at what NAND driver the board selects, and whether that driver ever asks for soft ECC. Signed-off-by: Scott Wood <scottwood@freescale.com>
* Merge branch 'sf' of git://git.denx.de/u-boot-blackfinWolfgang Denk2012-02-13-12/+16
|\ | | | | | | | | | | | | | | * 'sf' of git://git.denx.de/u-boot-blackfin: README: Add description of SPI Flash (SF) command configuration sf command: allow default bus and chip selects sf: eeprom_m95xxx: set a sane default timeout sf: eeprom_m95xxx: fix up style
| * sf: eeprom_m95xxx: set a sane default timeoutMike Frysinger2012-02-12-0/+4
| | | | | | | | | | | | | | Every board currently defines this to the same value, so just default to that to avoid having to make everyone do the same thing. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * sf: eeprom_m95xxx: fix up styleMike Frysinger2012-02-12-12/+12
| | | | | | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* | Blackfin: bfin_nand: mark local func staticMike Frysinger2012-02-12-1/+1
|/ | | | | | This devready func is only used in this driver, so mark it static. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-cfi-flashWolfgang Denk2012-02-11-0/+23
|\ | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-cfi-flash: add STM29F400BB to table of supported legacy flashs * Fix: watchdog timed out, if flash blank (0xFF) blocks
| * add STM29F400BB to table of supported legacy flashsDavid Müller (ELSOFT AG)2012-02-09-0/+20
| | | | | | | | | | Signed-off-by: David Mueller <d.mueller@elsoft.ch> Signed-off-by: Stefan Roese <sr@denx.de>
| * * Fix: watchdog timed out, if flash blank (0xFF) blocksJens Scharsig (BuS Elektronik)2012-02-09-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current implementation of cfi_flash uses udelay to reset watchdog. If several blocks are blank (0xff filled) the watchdog timed out. The reason is, udelay is never called, if flash device is ready to fast. e.g. mw.w $(copy_addr) FFFF 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog timed out mw.w $(copy_addr) 0000 10000;cp.b $(copy_addr) 10880000 20000 -> watchdog not timed out This patch adds an extra watchdog reset in front of flash ready check. Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Stefan Roese <sr@denx.de>
* | nand/fsl_elbc: Convert to self-initScott Wood2012-01-26-5/+38
| | | | | | | | | | | | | | | | This driver doesn't yet make use of the added flexibility (not that that should stop anyone from converting...), but it will with the in-progress hack to support 4k-page NAND. Signed-off-by: Scott Wood <scottwood@freescale.com>
* | nand: Introduce CONFIG_SYS_NAND_SELF_INITScott Wood2012-01-26-37/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | This allows a driver to run code between nand_scan_ident() and nand_scan_tail(), among other things. See the additions to doc/README.nand for details. To allow a gradual transition, Boards that don't set CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but new drivers should not require this, and existing drivers should be converted when convenient. Signed-off-by: Scott Wood <scottwood@freescale.com>
* | mtd/nand: Add ONFI support for FSL NAND controllerShengzhou Liu2012-01-26-7/+10
| | | | | | | | | | | | | | | | - fix NAND_CMD_READID command for ONFI detect. - add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | nand: make 1-bit software ECC configurableChristian Hitz2012-01-26-1/+5
| | | | | | | | | | | | | | | | | | | | The software ECC algorithm is not necessary when hardware ECC is available and can be left out for a smaller image size. Enable with CONFIG_MTD_ECC_SOFT. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | nand: Sanitize ONFI strings.Christian Hitz2012-01-26-1/+22
| | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This is part of the synchronization with the nand driver to the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | nand: Merge changes to BBT from Linux nand driverChristian Hitz2012-01-26-99/+328
| | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | nand: Merge changes from Linux nand driverChristian Hitz2012-01-26-150/+309
| | | | | | | | | | | | | | | | | | | | | | [backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe] This patch synchronizes the nand driver with the Linux 3.0 state. Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> [scottwood@freescale.com: minor fixes] Signed-off-by: Scott Wood <scottwood@freescale.com>
generated by cgit v1.1 at 2024-11-14 21:39:55 +0000