| Commit message (Collapse) | Author | Age | Lines | |
|---|---|---|---|---|
| * | mtd: nand: am335x: Fix 'bit-flip' errors in SPL | Rostislav Lisovy | 2014-09-25 | -4/+8 |
| | | | | | | | | | | | | | | | | | OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip corrected' error messages. Possible cause was discussed in the mailinglist thread: http://lists.denx.de/pipermail/u-boot/2014-April/177508.html The issue was partially fixed with the cc81a5291910d7a.git however this has to be done to fix the SPL. The original author of the code is Belisko Marek <marek.belisko@gmail.com> Signed-off-by: Rostislav Lisovy <lisovy@merica.cz> | |||
| * | mtd: nand: force NAND_CMD_READID onto 8-bit bus | Brian Norris | 2014-06-06 | -1/+1 |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As per following Sections in ONFI Spec, NAND_CMD_READID should use only lower 8-bit for transfering command, address and data even on x16 NAND device. *Section: Target Initialization" "The Read ID and Read Parameter Page commands only use the lower 8-bits of the data bus. The host shall not issue commands that use a word data width on x16 devices until the host determines the device supports a 16-bit data bus width in the parameter page." *Section: Bus Width Requirements* "When the host supports a 16-bit bus width, only data is transferred at the 16-bit width. All address and command line transfers shall use only the lower 8-bits of the data bus. During command transfers, the host may place any value on the upper 8-bits of the data bus. During address transfers, the host shall set the upper 8-bits of the data bus to 00h." Thus porting following commit from linux-kernel to ensure that column address is not altered to align to x16 bus when issuing NAND_CMD_READID command. commit 3dad2344e92c6e1aeae42df1c4824f307c51bcc7 mtd: nand: force NAND_CMD_READID onto 8-bit bus Author: Brian Norris <computersforpeace@gmail.com> (preserving authorship) The NAND command helpers tend to automatically shift the column address for x16 bus devices, since most commands expect a word address, not a byte address. The Read ID command, however, expects an 8-bit address (i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or 0x20). This fixes the column address for a few drivers which imitate the nand_base defaults. Signed-off-by: Pekon Gupta <pekon@ti.com> | |||
| * | mtd: Add a CONFIG_SPL_MTD_SUPPORT for a more full NAND subsystem in SPL | Tom Rini | 2014-04-17 | -27/+27 |
| | | | | | | | | | This mainly converts the am335x_spl_bch driver to the "normal" format which means a slight change to nand_info within the driver. Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Tom Rini <trini@ti.com> | |||
| * | Add GPL-2.0+ SPDX-License-Identifier to source files | Wolfgang Denk | 2013-07-24 | -13/+1 |
| | | | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com> | |||
| * | am33xx_spl_bch: simple SPL nand loader for AM33XX | Ilya Yanok | 2012-12-10 | -0/+238 |
| AM33XX with BCH8 can't work with nand_spl_simple correctly because custom read_page implementation is required for proper syndrome generation. This simple driver mostly duplicates nand_spl_simple but has nand_read_page changed to suit our needs. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com> | ||||
 |
index : arm-boot/u-boot-imx.git | |
| U-boot NXP imx6 | git@iatec.biz |
| summaryrefslogtreecommitdiff |