summaryrefslogtreecommitdiff
path: root/drivers/mmc/sdhci.c
Commit message (Collapse)AuthorAgeLines
* mmc: sdhci: assign to clk_mul when host version is upper than SD3.0Jaehoon Chung2016-10-28-3/+5
| | | | | | To prevent the wrong value check the SD version. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: sdhci: fix the "misaligned operation at range" for cacheJaehoon Chung2016-10-28-0/+1
| | | | | | | | This pathc is fixed the below thing. If misaligned the cache range, Just flush to CACHLINE_SIZE. "CACHE: Misaligned operation at range [7ae55b00, 7ae55b08]" Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: sdhci: use the generic error numberJaehoon Chung2016-10-10-6/+6
| | | | | | | Use the generic error number instead of meaningless value. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* mmc: sdhci: use the host version value in sdhci_setup_cfgJaehoon Chung2016-10-10-1/+5
| | | | | | | | "host->version" isn't a SoC specific value. It doesn't need to get in each SoC drivers. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
* mmc: sdhci: Add the programmable clock mode supportWenyou Yang2016-09-20-10/+40
| | | | | | Add the programmable clock mode for the clock generator. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
* mmc: sdhci: drop CONFIG_ from CONFIG_SDHCI_CMD_MAX_TIMEOUTMasahiro Yamada2016-09-20-6/+3
| | | | | | | | | No need for per-SoC adjustment for this parameter. It should be determined by the slowest hardware. Currently, no board overrides this CONFIG, so 3.2 sec is large enough. (If not, we can make it even larger.) Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: sdhci: drop CONFIG_ from CONFIG_SDHCI_CMD_DEFAULT_TIMEMasahiro Yamada2016-09-20-2/+2
| | | | | | | | This CONFIG is not configurable since it is not guarded by #ifndef. Nobody has complained about that, so there is no need to keep it as a CONFIG option. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: sdhci: move SDMA capability check to sdhci_setup_cfg()Masahiro Yamada2016-09-20-11/+8
| | | | | | | | If CONFIG_BLK is enabled, add_sdhci() is never called. Move this quirk handling to sdhci_setup_cfg(), which is now the central place for hardware capability checks. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: sdhci: move broken voltage quirk handling to sdhci_setup_cfg()Masahiro Yamada2016-09-20-3/+3
| | | | | | | | If CONFIG_BLK is enabled, add_sdhci() is never called. Move this quirk handling to sdhci_setup_cfg(), which is now the central place for hardware capability checks. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: sdhci: move error message to more relevant placeMasahiro Yamada2016-09-20-6/+9
| | | | | | | | "Hardware doesn't specify base clock frequency" may not be only the error case of sdhci_setup_cfg(). It is better to print this where the corresponding error is triggered. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: sdhci: move sdhci_reset() call to sdhci_init()Masahiro Yamada2016-09-20-2/+2
| | | | | | | | | | | If CONFIG_BLK is enabled, add_sdhci() is never called. So, sdhci_reset() is not called, either. This is a problem for my board as it needs the reset to start from a sane state. Move the add_sdhci() call to sdhci_init(), which is visited by both of the with/without CONFIG_BLK cases. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* mmc: sdhci: fix the compiler warning when disable CONFIG_MMC_SDMAJaehoon Chung2016-08-05-1/+1
| | | | | | | When disabled CONFIG_MMC_SDMA, variable caps didn't use. This patch fixes the compiler error for -Wunused-but-set-variable Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: sdhci: remove the unnecessary arguments for sdhci_setup_cfgJaehoon Chung2016-08-05-12/+14
| | | | | | | | | | | | | | Some arguments don't need to pass to sdhci_setup_cfg. Generic variable can be used in sdhci_setup_cfg, and some arguments are already included in sdhci_host struct. It's enough that just pass the board specific things to sdhci_setup_cfg(). After removing the unnecessary arguments, it's more simpler than before. It doesn't consider "Version" and "Capabilities" anymore in each SoC driver. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* mmc: sdhci: remove the unused argument for sdhci_setup_cfgJaehoon Chung2016-08-05-2/+2
| | | | | | | | buswidth isn't used anywhere in sdhci_setup_cfg. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* mmc: sdhci: revert "mmc: sdhci: Claer high speed if not supported"Jaehoon Chung2016-08-05-3/+0
| | | | | | | | | | | | | | | | This "commit 429790026021d522d51617217d4b86218cca5750" is wrong. SDHCI_QUIRK_NO_HISPD_BIT is for skipping to set CTRL_HISPD bit. For example, Exynos didn't have CTRL_HISPD. But Highspeed mode is supported. (This quirks doesn't mean that driver didn't support the Highseepd mode.) Note: If driver didn't support the Highspeed Mode, use or add the other quirks. After applied this patch, all Exynos SoCs are just running with 25MHz. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: use the generic error numberJaehoon Chung2016-08-05-4/+4
| | | | | | | | | Use the generic error number instead of specific error number. If use the generic error number, it can debug more easier. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
* mmc: sdhci: set to INT_DATA_END when there are dataJaehoon Chung2016-08-05-1/+2
| | | | | | | | | | | | There is no data, it doesn't needs to wait for completing data transfer. (It seems that it can be removed.) Almost all timeout error is occured from stop command without data. After applied this patch, I hope that we don't need to increase timeout value anymore. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* mmc: sdhci: clean up timeout detectionMasahiro Yamada2016-08-05-9/+9
| | | | | | | | | | | | | The current timeout detection logic is not very nice; it calls get_timer(start) in the while() loop, and then calls it again after the loop to check if a timeout error happened. Because of the time difference between the two calls of get_timer(), the timeout detected after the loop may not be true. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: sdhci: Disable internal clock enable bitSiva Durga Prasad Paladugu2016-07-22-1/+1
| | | | | | | | | | | Disable internal clock by clearing the internal clock enable bit. This bit needs to be cleared too when we stop the SDCLK for changing the frequency divisor. This bit should be set to zero when the device is not using the Host controller. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* dm: mmc: sdhci: Support CONFIG_BLK and CONFIG_DM_MMC_OPSSimon Glass2016-07-11-1/+39
| | | | | | | Add support for using driver model for block devices and MMC operations in this driver. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: mmc: sdhci: Refactor configuration setup to support DMSimon Glass2016-07-11-48/+59
| | | | | | | Move the configuration setting into a separate function which can be used by the driver-model code. Signed-off-by: Simon Glass <sjg@chromium.org>
* mmc: increase MMC SDHCI read status timeoutSteve Rae2016-07-01-2/+3
| | | | | | | | | | | | | | | | | | | | | | Otherwise, ocassionally see errors like this: Flashing sparse image at offset 2078720 Flashing Sparse Image sdhci_send_command: Timeout for status update! mmc fail to send stop cmd write_sparse_image: Write failed, block #2181088 [0] This does not affect the actual writing speed, which is controlled by the default value: CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT It only increases the retries when reading: SDHCI_INT_STATUS to avoid the timeout error. Signed-off-by: Steve Rae <steve.rae@raedomain.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
* dm: mmc: Convert sdhci to support CONFIG_BLKSimon Glass2016-05-27-1/+1
| | | | | | Update sdhci.c so that it works with driver model enabled for block devices. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: block: Rename device number member dev to devnumSimon Glass2016-03-14-1/+1
| | | | | | | | | This is a device number, and we want to use 'dev' to mean a driver model device. Rename the member. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
* drivers: mmc: add driver for Microchip PIC32 SDHCI controller.Andrei Pistirica2016-02-01-0/+7
| | | | | | | | | | | This driver implements platform specific glue and fixups for PIC32 internal SDHCI controller. Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com> Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com> Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
* mmc: sdhci: Clear high speed if not supportedSiva Durga Prasad Paladugu2016-01-27-0/+4
| | | | | | | | | Clear high speed bit if it was not supported by the driver. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Emil Lenchak <emill@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* mmc: sdhci: Fix the SD clock stop sequenceWenyou Yang2015-11-03-2/+18
| | | | | | | | | | | | According to the SDHC specification, stopping the SD Clock is by setting the SD Clock Enable bit in the Clock Control register at 0, instead of setting all bits at 0. Before stopping the SD clock, we need to make sure all SD transactions to complete, so add checking the CMD and DAT bits in the Presen State register, before stopping the SD clock. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
* mmc: sdhci.c: Add config option to use a fixed buffer for transfersStefan Roese2015-07-10-0/+15
| | | | | | | | | | | | | | | | | | | | While implementing SDIO/MMC SPL booting for the Marvell Armada 38x, the following problem occured. The SPL runs in internal SRAM which is the L2 cache locked to memory. When the MMC buffers now are located on the stack (or bss), the SDIO controller (SDHCI) can't write into this L2 cache memory. This patch introduces a method to use a fixed buffer that will be used for all transfers by defining CONFIG_FIXED_SDHCI_ALIGNED_BUFFER. This way, the board can use this buffer address located in SDRAM for all transfers. This solves this SPL problem on the A38x and should only be used in the SPL U-Boot version. Tested for SPL booting on Marvell Armada 38x DB-88F6820-GP board. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
* mmc: sdhci: Use timer based timeout detection in sdhci_send_command()Stefan Roese2015-07-10-5/+5
| | | | | | | | | | | | | The loop counter based timeout detection does not work on the Armada 38x based board (DB-88F6820-GP). At least with dcache enabled a timeout is detected. Without dcache enabled, the timeout does not occur. Increasing the loop counter solves this issue. But a better solution is to use a timer based timeout detection instead. This patch now implements this timer based detection. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
* mmc: sdhci: add timeout setting for response busy commandKevin Liu2015-05-05-0/+2
| | | | | | | | | | Timeout interrupt also work for response busy command(R1b) like cmd38/cmd6. So need to set it accordingly. Current code only set timeout for data command. Signed-off-by: Kevin Liu <kliu5@marvell.com> Signed-off-by: Rob Herring <robh@kernel.org> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
* sdhci: fix warnings on 64-bit buildsRob Herring2015-03-18-3/+3
| | | | | | | | Change addresses to unsigned long to be compatible with 64-bit builds. Regardless of fixing warnings, the device is still only 32-bit capable. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: sdhci: don't clobber adjacent registersMatt Reimer2015-03-18-1/+1
| | | | | | | | SDHCI_HOST_CONTROL is a byte-sized register, so don't write to it as if it were a long, as that would result in clobbering the three registers following. Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
* mmc: sdhci: fix bus width switching on Samsung SoCsMatt Reimer2015-02-23-1/+2
| | | | | | | | | | | | Fix bus width switching from 8-bit mode down to 4-bit or 1-bit modes on Samsung SoCs using SDHCI_QUIRK_USE_WIDE8. These SoCs report controller version 2.0 yet they support 8-bit bus widths. If 8-bit mode was previously enabled and then an operation like "mmc dev" caused a switch back down to 4-bit or 1-bit mode, WIDE8 was left set, causing failures. This problem was manifested by "mmc dev" timing out. Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
* sdhci: make local functions staticJeroen Hofstee2014-10-25-3/+3
| | | | Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
* mmc: Split mmc struct, rework mmc initialization (v2)Pantelis Antoniou2014-03-24-37/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The way that struct mmc was implemented was a bit of a mess; configuration and internal state all jumbled up in a single structure. On top of that the way initialization is done with mmc_register leads to a lot of duplicated code in drivers. Typically the initialization got something like this in every driver. struct mmc *mmc = malloc(sizeof(struct mmc)); memset(mmc, 0, sizeof(struct mmc); /* fill in fields of mmc struct */ /* store private data pointer */ mmc_register(mmc); By using the new mmc_create call one just passes an mmc config struct and an optional private data pointer like this: struct mmc = mmc_create(&cfg, priv); All in tree drivers have been updated to the new form, and expect mmc_register to go away before long. Changes since v1: * Use calloc instead of manually calling memset. * Mark mmc_register as deprecated. Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: Convert mmc struct's name array to a pointerPantelis Antoniou2014-03-24-1/+1
| | | | | | | Using an array is pointless; even more pointless (and scary) is using sprintf to fill it without a format string. Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: Remove ops from struct mmc and put in mmc_opsPantelis Antoniou2014-03-24-5/+8
| | | | | | | | | | | | | | | | | Remove the in-structure ops and put them in mmc_ops with a constant pointer to it. This makes the mmc structure smaller as well as conserving code space (in theory). All in-tree drivers are converted as well; this is done in a single patch in order to not break git bisect. Changes since V1: Fix compilation b0rked issue on omap platforms where OMAP_GPIO was not set. Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: Minor cleanup of sdhci.cDarwin Rambo2014-01-09-13/+19
| | | | | | | | Fixup prints to show where the print is done from, and a few minor formatting/grammar issues. Signed-off-by: Darwin Rambo <drambo@broadcom.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: sdhci: Avoid commands errors by simple timeout adaptation.Przemyslaw Marczak2013-10-31-7/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | Old command timeout value was too small and it caused I/O errors which led to uncompleted read/write/erase operations and filesystem errors. Timeout adaptation fixes this issue. Changes in sdhci_send_command() function: - change timeout variable to static - increase default command timeout to 100 ms - add definition of max command timeout value, which can be redefined in each board config file - wait for card ready state for max defined time if it doesn't exceed defined maximum or return COMM_ERR Once successfully increased timeout value will be used in next function call. This fix was tested on Goni, Trats, Trats2 boards by testing UMS on MMC storage. Changes v2: - move global variable cmd_timeout into function sdhci_send_command() - change condition "==" to ">=" when comparing time with timeout - print information about timeout increasing and card busy timeout Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
* Fix wrong sdhci host control register read and writeJuhyun \(Justin\) Oh2013-09-20-3/+2
| | | | | | | | | | | | | | | | The patch fixes the improper read and write of sdhci host control register for sdma transfer. The problem comes when reading and writing 1 byte long host control register with the sdhci_readl() and sdhci_writel(). The misuse of these functions overwrite the value of the next registers which are in 4 bytes boundary. This patch replaces four byte register read/write functions with one byte read/write ones. Beside, it eliminates unnecessary bit operation. i.e. or-ing zero against a variable. Signed-off-by: Juhyun (Justin) Oh <Juhyun_Oh@sigmadesigns.com>
* mmc: sdhci: use the SDHCI_QUIRK_USE_WIDE8 for samsung SoCJaehoon Chung2013-09-17-6/+7
| | | | | | | | | Samsung SoC is supported the WIDE8, even if Controller version is v2.0. So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* mmc: sdhci: Enable 8-bit bus width only for 3.0 spec onwardsJagannadha Sutradharudu Teki2013-06-13-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | CAP register don't have any information for 8-bit buswidth support on 2.0 sdhci spec, only from 3.0 onwards bit[18] got this information. Due to this misassignment in sdhci, mmc is setting 8-bit buswidth using mmc_set_bus_width even if controller doesn't support. Below change has code information. "mmc: Properly determine maximum supported bus width" (sha1: 7798f6dbd5e1a3030ed81a81da5dfb57c3307cac) Bug log: <mmc plus and emmc cards) ------- zynq-uboot> mmcinfo Error detected in status(0x208100)! Device: zynq_sdhci Manufacturer ID: fe ..... So enable 8-bit support only for 3.0 spec using CAP and for below 3.0 assign mmc->host_caps = MMC_MODE_8BIT on respective platform driver if host have a support. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-03-26-3/+5
|\
| * mmc:sdhci:fix: Change default interrupts enabled at SDHCI initializationƁukasz Majewski2013-03-12-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch changes sdhci_init()'s behavior to NOT enable all interrupt sources by default. Moreover interrupt signaling has been disabled. This patch do not enable interrupts which aren't served in u-boot (they are defined at sdhci.h but NOT used elsewhere): - SDHCI_INT_CARD_INSERT, SDHCI_INT_CARD_REMOVE, SDHCI_BUS_POWER, SDHCI_INT_CARD_REMOVE, SDHCI_INT_CARD_INT Special care shall be put on SDHCI_INT_CARD_INT, which indicates interrupt generated by SD card. According to "SD Host Controller Simplified Spec. ver 3.00" when bit 8 (Card Interrupt Status Enable) at "Normal Interrupt Status Enable Register" (offset 0x34) is set, the card interrupt detection is started. Then eMMC card may cause the SD controller to set this bit and then this interrupt is passed to booted OS and might cause kernel crash. To sum up: - Only enable interrupts, which are served at u-boot - This cleanup as a side effect fixes SDHCI's CARD INTERRUPT problem at Linux kernel (versions 3.6+, sdhci controller) - Keep masked bits at "Normal Interrupt Signal Enable Register" (0x38h) Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lei Wen <leiwen@marvell.com> Cc: Andy Fleming <afleming@freescale.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | mmc: add support for write protectionNikita Kiryanov2013-03-08-0/+1
|/ | | | | | | Add generic mmc write protection functionality. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* mmc: add no simultaenous power and vddMela Custodio2012-11-27-0/+3
| | | | | | | | | | | | | | | | | | Bring in the code from Linux kernel. Added to Linux kernel by: commit e08c1694d9e2138204f2b79b73f0f159074ce2f5 Author: Andres Salomon <dilinger@queued.net> Date: Fri Jul 4 10:00:03 2008 -0700 Some HW balks when writing both voltage setting and power up at the same time to SDHCI_POWER_CONTROL register. Signed-off-by: Rommel G Custodio <sessyargc@gmail.com> CC: Andy Fleming <afleming@freescale.com> v2: fix attribution and SOB Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: sdhci: Add a quirk to add delay during completion of sdhci_send_cmdTushar Behera2012-10-22-0/+3
| | | | | | | | | | | | | | | | | MMC host controller requires a delay between every sdhci_send_cmd() execution. In s5p_mmc driver (s5p_sdhci replaces this driver), a delay of 1000us was provided after every mmc_send_cmd() call. Adding a quirk in current sdhci driver to replicate the behaviour. Without this delay, MMC initialization on Origen board fails with following error messages. Timeout for status update! mmc fail to send stop cmd Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: sdhci: add the DMA select for SDMAJaehoon Chung2012-10-22-0/+7
| | | | | | | | | | In host-control register, DMA select bit field is present. BUt in sdhci.c, didn't select for DMA. if set CONFIG_MMC_SDMA, we need to set SDMA-select bit. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: sdhci: increase the timeout value for data transferJaehoon Chung2012-10-22-1/+1
| | | | | | | | | | | | Timeout value is tunable. When run read/write operation, sometime returned the timeout error. Because the timeout value is too short. So increased the enough timeout value. (This timeout value is used to prevent the infinite loop.) Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>