summaryrefslogtreecommitdiff
path: root/drivers/mmc/mmc.c
Commit message (Collapse)AuthorAgeLines
* mmc: Fix erase_grp_size for partitioned cardOliver Metz2013-10-31-4/+13
| | | | | | | | EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or power off. Set it if device has enhanced partitions. Signed-off-by: Oliver Metz <oliver@freetz.org> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: don't support write & erase for SPL buildsPaul Burton2013-09-20-182/+4
| | | | | | | | | | For SPL builds this is just dead code since we'll only need to read. Eliminating it results in a significant size reduction for the SPL binary, which may be critical for certain platforms where the binary size is highly constrained. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* mmc: don't call *printf or puts when SPL & !CONFIG_SPL_LIBCOMMON_SUPPORTPaul Burton2013-09-17-0/+36
| | | | | | | | If we don't have CONFIG_SPL_LIBCOMMON_SUPPORT defined then stdio & *printf functions are unavailable & calling them will cause a link failure. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
* mmc: Remove unused variable backup from mmc_send_cmd()Oleksandr Tyshchenko2013-09-17-3/+0
| | | | | | | | Do not call a memset for unused variable backup every time. Remove unused variable from function. Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
* powerpc: mpc85xx: Support booting from SD Card with SPLYing Zhang2013-08-20-0/+2
| | | | | | | | | | | | | | | | The code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* Fix block device accesses beyond 2TiBSascha Silbe2013-06-26-8/+9
| | | | | | | | | | | | | | | | | | With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type, which is required to represent block numbers for storage devices that exceed 2TiB (the block size usually is 512B), e.g. recent hard drives. For some obscure reason, the current U-Boot code uses lbaint_t for the number of blocks to read (a rather optimistic estimation of how RAM sizes will evolve), but not for the starting address. Trying to access blocks beyond the 2TiB boundary will simply wrap around and read a block within the 0..2TiB range. We now use lbaint_t for block start addresses, too. This required changes to all block drivers as the signature of block_read(), block_write() and block_erase() in block_dev_desc_t changed. Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-06-22-0/+134
|\
| * Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD2013-06-19-0/+134
| |\ | | | | | | | | | | | | Conflicts: spl/Makefile
| | * MMC: APIs to support resize of EMMC boot partitionAmar2013-06-13-0/+134
| | | | | | | | | | | | | | | | | | | | | This patch adds APIs to access(open / close) and to resize boot partiton of EMMC. Signed-off-by: Amar <amarendra.xt@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | | mmc: report capacity for the selected partitionStephen Warren2013-06-13-7/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enhance the MMC core to calculate the size of each MMC partition, and update mmc->capacity whenever a partition is selected. This causes: mmc dev 0 1 ; mmcinfo ... to report the size of the currently selected partition, rather than always reporting the size of the user partition. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | | mmc write bug fixRuud Commandeur2013-06-13-3/+5
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a bug related to mmc writes. When doing fatwrites on an SD-Card, MMC bus problems can occur. Depending on the size of the file, "MMC0: Bus busy timeout!" is reported, resulting in an SD-Card that is no longer responding. It appears to be, that set_cluster can be called with a size being zero. That can be with a file that has a size being an exact multiple (including 0) of the clustersize, but also for files that are smaller than the size of one cluster. The same problem occurs if the "mmc write" command is given with a block count being 0. By adding a check for the block count being zero in mmc_write_blocks (drivers/mmc.c), this problem is solved. Signed-off-by: Ruud Commandeur <rcommandeur@clb.nl> Cc: Tom Rini <trini@ti.com> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Mats Karrman <Mats.Karrman@tritech.se> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | mmc: Split device init to decouple OCR-polling delayChe-Liang Chiou2013-05-06-32/+105
|/ | | | | | | | | | | | | | | | | | | Most of time that MMC driver spends on initializing a device is polling OCR (operation conditions register). To decouple this polling loop, device init is split into two parts: The first part fires the OCR query command, and the second part polls the result. So the caller is now no longer bound to the OCR-polling delay; he may fire the query, go somewhere and then come back later for the result. To use this, call mmc_set_preinit() on any device which needs this. This can save significant amounts of time on boot (e.g. 200ms) by hiding the MMC init time behind other init. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* part/dev_desc: Add log2 of blocksize to block_dev_desc data structEgbert Eich2013-05-01-0/+1
| | | | | | | | | | log2 of the device block size serves as the shift value used to calculate the block number to read in file systems when implementing avaiable block sizes. It is needed quite often in file systems thus it is pre-calculated and stored in the block device descriptor. Signed-off-by: Egbert Eich <eich@suse.com>
* mmc: Define a constant for the maximum block sizeSimon Glass2013-05-01-12/+13
| | | | | | | | | The number 512 appears quite a bit in the mmc code. Add a constant for this so that it can be used here and in other parts of the code (e.g. SPL code which loads from mmc). Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Vadim Bendebury <vbendeb@google.com>
* mmc: check the revision for sd3.0Jaehoon Chung2013-04-17-0/+2
| | | | | | | | Support to check whether the SD3.0 or not. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Rommel Custodio <sessyargc@gmail.com>
* mmc: support the correct card version for eMMCJaehoon Chung2013-04-17-0/+18
| | | | | | | | | | | eMMC vesrion is supported up to v4.5. But bootloader isn't saw the exact eMMC version. After applied this patch, if use the mmcinfo command, then can see the exactly mmc version. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Rommel Custodio <sessyargc@gmail.com>
* mmc: mmc_getcd/getwp: use sensible defaultsPeter Korsgaard2013-03-24-4/+12
| | | | | | | | | Let mmc_getcd() return true and mmc_getwp() false if mmc driver doesn't provide handlers for them. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com> [trini: Add braces around first if test in each case to fix warning] Signed-off-by: Tom Rini <trini@ti.com>
* mmc: add support for write protectionNikita Kiryanov2013-03-08-0/+17
| | | | | | | Add generic mmc write protection functionality. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* mmc: Properly determine maximum supported bus widthAndy Fleming2012-11-27-12/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | At some point, a confusion arose about the use of the bit definitions in host_caps for bus widths, and the value in ext_csd. By coincidence, a simple shift could convert between one and the other: MMC_MODE_1BIT = 0, EXT_CSD_BUS_WIDTH_1 = 0 MMC_MODE_4BIT = 0x100, EXT_CSD_BUS_WIDTH_4 = 1 MMC_MODE_8BIT = 0x200, EXT_CSD_BUS_WIDTH_8 = 2 However, as host_caps is a bitmask of supported things, there is not, in fact, a one-to-one correspondence. host_caps is capable of containing MODE_4BIT | MODE_8BIT, so nonsensical things were happening where we would try to set the bus width to 12. The new code clarifies the very different namespaces: host_caps/card_caps = bitmask (MMC_MODE_*) ext CSD fields are just an index (EXT_CSD_BUS_WIDTH_*) mmc->bus_width integer number of bits (1, 4, 8) We create arrays to map between the namespaces, like in Linux. Signed-off-by: Andy Fleming <afleming@freescale.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Stephen Warren <swarren@nvidia.com>
* mmc: Fix interpretation of MMC_CMD_ALL_SEND_CIDTaylor Hutt2012-11-27-7/+9
| | | | | | | | | | | | The interpretation of the data returned by the MMC_CMD_ALL_SEND_CID command was incorrect with respect to the JEDEC Standard No. 84-A441. This change makes the interpretation correct with respect to the defined fields of the CID register. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Taylor Hutt <thutt@chromium.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* drivers/mmc/mmc.c: sparse fixesKim Phillips2012-11-04-18/+19
| | | | | | | | | | | | | | | | | | | | | | mmc.c:137:5: warning: symbol 'mmc_send_cmd' was not declared. Should it be static? mmc.c:203:5: warning: symbol 'mmc_send_status' was not declared. Should it be static? mmc.c:247:5: warning: symbol 'mmc_set_blocklen' was not declared. Should it be static? mmc.c:440:5: warning: symbol 'mmc_read_blocks' was not declared. Should it be static? mmc.c:510:5: warning: symbol 'mmc_go_idle' was not declared. Should it be static? mmc.c:532:1: warning: symbol 'sd_send_op_cond' was not declared. Should it be static? mmc.c:597:5: warning: symbol 'mmc_send_op_cond' was not declared. Should it be static? mmc.c:661:5: warning: symbol 'mmc_send_ext_csd' was not declared. Should it be static? mmc.c:683:5: warning: symbol 'mmc_switch' was not declared. Should it be static? mmc.c:705:5: warning: symbol 'mmc_change_freq' was not declared. Should it be static? mmc.c:775:5: warning: symbol 'sd_switch' was not declared. Should it be static? mmc.c:796:5: warning: symbol 'sd_change_freq' was not declared. Should it be static? mmc.c:935:6: warning: symbol 'mmc_set_ios' was not declared. Should it be static? mmc.c:953:6: warning: symbol 'mmc_set_bus_width' was not declared. Should it be static? mmc.c:1108:26: warning: dubious: !x & y mmc.c:960:5: warning: symbol 'mmc_startup' was not declared. Should it be static? mmc.c:1243:5: warning: symbol 'mmc_send_if_cond' was not declared. Should it be s Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* MMC: Remove the MMC bounce bufferMarek Vasut2012-10-22-92/+0
| | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andy Fleming <afleming@freescale.com> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc_get_dev: Return error if mmc_init failsBenoît Thébaudeau2012-09-05-2/+1
| | | | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: detect boot sectors using EXT_CSD_BOOT_MULT tooStephen Warren2012-09-05-1/+2
| | | | | | | | | | | | | | | | | Some eMMC devices contain boot partitions, but do not set the PART_SUPPORT bit in EXT_CSD_PARTITIONING_SUPPORT. Allow partition selection on such devices, by enabling partition switching when EXT_CSD_BOOT_MULT is set. Note that the Linux kernel enables access to boot partitions solely based on the value of EXT_CSD_BOOT_MULT; EXT_CSD_PARTITIONING_SUPPORT only influences access to "general" partitions. eMMC devices affected by this issue exist on various NVIDIA Tegra platforms (and presumably many others too), such as Harmony (plug-in eMMC), Seaboard, Springbank, and Whistler (plug-in eMMC). Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* MMC: u-boot-spl may be compiled without partition supportMikhail Kshevetskiy2012-09-05-0/+2
| | | | | Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: fix capacity calculation when EXT_CSD_SEC_CNT is usedYoshihiro Shimoda2012-09-05-5/+5
| | | | | | | | | | | | | | | | Since the type of "ext_csd" was array of char, the following calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT] was minus. capacity = ext_csd[EXT_CSD_SEC_CNT] << 0 | ext_csd[EXT_CSD_SEC_CNT + 1] << 8 | ext_csd[EXT_CSD_SEC_CNT + 2] << 16 | ext_csd[EXT_CSD_SEC_CNT + 3] << 24; So, this patch changes the type of "ext_csd" to array of u8. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: fix wrong timeout check in mmc_send_status()Jongman Heo2012-09-05-1/+1
| | | | | | | | | | (!timeout) condition check in mmc_send_status() can never be met, because do-while loop ends up with negative timeout value, -1. Fix the check to handle TIMEOUT case correctly. Signed-off-by: Jongman Heo <jongman.heo@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: Remove unused item flags in struct mmc_cmdKaspter Ju2012-09-02-28/+0
| | | | Signed-off-by: Kaspter Ju <nigh0st3018@gmail.com>
* SD/MMC: check the card status during erase operationJerry Huang2012-07-13-0/+5
| | | | | | | | | | | | | | | | | | | Use the function 'mmc_send_status' to check the card status. only when the card is ready, driver can send the next erase command to the card, otherwise, the erase will failed: => mmc erase 0 1 MMC erase: dev # 0, block # 0, count 1 ... 1 blocks erase: OK => mmc erase 0 2 MMC erase: dev # 0, block # 0, count 2 ... mmc erase failed 1 blocks erase: ERROR => mmc erase 0 4 MMC erase: dev # 0, block # 0, count 4 ... mmc erase failed 1 blocks erase: ERROR Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> CC: Andy Fleming <afleming@gmail.com> CC: Marek Vasut <marex@denx.de> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc:fix Call mmc_init() when executing mmc_get_dev()Łukasz Majewski2012-07-13-1/+4
| | | | | | | | | | | | | | | | | | | | This code adds call to mmc_init(), for partition related commands (e.g. fatls, fatinfo etc.). It is safe to call mmc_init() multiple times since mmc->has_init flag prevents from multiple initialization. The FAT related code calls get_dev high level method and then uses elements from mmc->block_dev, which is uninitialized until the mmc_init (and thereof mmc_startup) is called. This problem appears on boards, which don't use mmc as the default place for envs Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc: remove the hard setting for tran_speedJaehoon Chung2012-07-13-6/+7
| | | | | | | | | mmc_set_clock is set to the hard-coding. But i think good that use the tran_speed value. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mmc:fix: Set mmc width according to MMC host capabilitiesŁukasz Majewski2012-05-08-1/+3
| | | | | | | | | | | This patch sets the MMC width according to the MMC host capabilities. It turned out, that there are some targets (e.g. GONI), which are able to read data from SPI only at 4 bit mode. This patch restricts the width number according to the MMC host. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Andy Fleming <afleming@gmail.com>
* mmc: Fix warning if CONFIG_MMC_TRACE is enabledDirk Behme2012-04-21-1/+1
| | | | | | | | | | | | | | Fix the warning mmc.c: In function 'mmc_send_cmd': mmc.c:87: warning: assignment from incompatible pointer type in case CONFIG_MMC_TRACE is enabled. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Andy Fleming <afleming@freescale.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de>
* drivers/mmc/mmc.c: Fix build warningAnatolij Gustschin2012-03-30-1/+1
| | | | | | | | | | | | Fix: mmc.c: In function 'mmc_bounce_buffer_start': mmc.c:132:13: warning: no return statement in function returning non-void [-Wreturn-type] Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
* MMC: Implement generic bounce bufferMarek Vasut2012-03-29-3/+99
| | | | | | | | | | This implements generic bounce buffer at the end of MMC command submission chain. Therefore if unaligned data are passed, they are copied. This stuff should be pushed down into the MMC subsystem to squash all places generating these unaligned data. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andy Fleming <afleming@gmail.com>
* mmc: make mmc_send_status() more reliableJan Kloetzke2012-02-15-8/+12
| | | | | | | | | Align the card status polling with the Linux kernel and retry the command at least five times. Also some cards apparently mishandle the status bits, so make sure to check the card state too. Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com> Cc: Andy Fleming <afleming@gmail.com>
* mmc: fix card busy pollingJan Kloetzke2012-02-15-8/+6
| | | | | | | | | | | | A MMC/SD card may always go into the programming state (and hence be busy) after a block write. Therefore always check the card state, even after single block writes. On the other hand there is no need to check the card status after a read. Also make sure that errors during busy polling are propagated upwards. Signed-off-by: Jan Kloetzke <jan.kloetzke@dspg.com> Cc: Andy Fleming <afleming@gmail.com>
* mmc: Implement card detection.Thierry Reding2012-01-08-0/+18
| | | | | | | | | | | Check for card detect each time an MMC/SD device is initialized. If card detection is not implemented, this code behaves as before and continues assuming a card is present. If no card is detected, has_init is reset for the MMC/SD device (to force initialization next time) and an error is returned. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
* mmc: Change board_mmc_getcd() function prototype.Thierry Reding2012-01-08-2/+2
| | | | | | | | | | | | | | | | | | | | | The new API no longer uses the extra cd parameter that was used to store the card presence state. Instead, this information is returned via the function's return value. board_mmc_getcd() returns -1 to indicate that no card-detection mechanism is implemented; 0 indicates that no card is present and 1 is returned if it was detected that a card is present. The rationale for this change can be found in the following email thread: http://lists.denx.de/pipermail/u-boot/2011-November/110180.html In summary, the old API was not consistent with the rest of the MMC API which always passes a struct mmc as the first parameter. Furthermore the cd parameter was used to mean "card absence" in some implementations and "card presence" in others. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Tested-by: Jason Liu <jason.hui@linaro.org>
* mmc: add host_caps checking avoid switch card improperlyMacpaul Lin2012-01-08-0/+10
| | | | | | | | | | | Add a host capability checking to avoid the mmc stack switch the card to HIGHSPEED mode when the card supports HIGHSPEED while the host doesn't. This patch avoid furthur transaction problem when the mmc/sd card runs different mode to the host. Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"Macpaul Lin2011-11-25-14/+2
| | | | | | | | | | | | | | | | | | | | This reverts commit 02f3029f1810b99869254d0cf0a71946a008a728. This patch add 3 times retry to CMD8 because the Marvell mmc controller doesn't obey the power ramp up process in the SD specification 6.4.1. (Please refer to figure 6.1 and 6.2 in the specification.) The CMD0 should be send after power ramp up has been finished. However, the Marvell mmc contorller must do power ramp up after the first CMD0 command has been send. This patch also affect existing platforms like Nokia N900 and other platforms. Signed-off-by: Macpaul Lin <macpaul@andestech.com> Acked-by: Lei Wen <leiwen@marvell.com> Acked-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com>
* mmc: CMD7:MMC_CMD_SELECT_CARD response fixAjay Bhargav2011-11-03-1/+1
| | | | | | | | | | | | | As per JEDEC document JESD84-A441 (page 105) response for CMD7 (MMC_CMD_SELECT_CARD) response should be R1 instead of R1b. In uboot we never take MMC to disconnected state and on powerup its always ideal state which later goes to stand-by state. from document footnote: R1 while selecting from Stand-By State to Transfer State; R1b while selecting from Disconnected State to Programming State. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* mmc: test mmc bus width on startupLei Wen2011-11-03-18/+26
| | | | | | | | | | | | | | For we don't know mmc bus width from reading registers, the only way to check is to test. Current compare offset is: EXT_CSD_PARTITIONING_SUPPORT EXT_CSD_ERASE_GROUP_DEF EXT_CSD_REV EXT_CSD_HC_ERASE_GRP_SIZE EXT_CSD_SEC_CNT Signed-off-by: Lei Wen <leiwen@marvell.com>
* mmc: change magic number to macro defineLei Wen2011-11-03-9/+12
| | | | | | | | Previous magic number is hard to parse its meaning, change it to respective macro definition Signed-off-by: Lei Wen <leiwen@marvell.com> Acked-by: WOlfgang Denk <wd@denx.de>
* mmc: retry the cmd8 to meet 74 clocks requirement in the specLei Wen2011-11-03-2/+14
| | | | | | | | | | For some controller it has dynamic clock gating, and only toggle out clk when the first cmd0 send out, while some card strictly obey the 74 clocks rule, the interval may not be sufficient between the cmd0 and this cmd8, retry to fulfil the clock requirement. Signed-off-by: Lei Wen <leiwen@marvell.com> Tested-by: Marek Vasut <marek.vasut@gmail.com>
* mmc: dcache: allocate cache aligned buffers for ext_csdAnton staaf2011-10-25-2/+2
| | | | | | | | | | | | | | | Currently the mmc_change_freq and mmc_startup functions allocates buffers on the stack that are passed down to the MMC device driver. These buffers could be unaligned to the L1 dcache line size. This causes problems when using DMA and with caches enabled. This patch correctly cache alignes the buffers used for reading the ext_csd data from an MMC device. Signed-off-by: Anton Staaf <robotboy@chromium.org> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
* mmc: dcache: allocate cache aligned buffer for scr and switch_statusAnton staaf2011-10-25-5/+5
| | | | | | | | | | | | | | | | | Currently the sd_change_freq function allocates two buffers on the stack that it passes down to the MMC device driver. These buffers could be unaligned to the L1 dcache line size. This causes problems when using DMA and with caches enabled. This patch correctly cache alignes the buffers used for reading the scr register and switch status values from an MMC device. Change-Id: Ifa8414f572ef907681bd2d5ff3950285a215357d Signed-off-by: Anton Staaf <robotboy@chromium.org> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Mike Frysinger <vapier@gentoo.org>
* mmc: Fix mmc_send_status()Marek Vasut2011-09-04-1/+2
| | | | | | | | The mmc_send_status() function sets cmd.arg = 0. That's incorrect, so fix it. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Andy Fleming <afleming@freescale.com> Tested-by: Lei Wen <adrian.wenl@gmail.com>
* disk/part.c: Make features optionalMatthew McClintock2011-07-26-0/+2
| | | | | | | | | If we don't want to build support for any partition types we can now add #undef CONFIG_PARTITIONS in a board config file to keep this from being compiled in. Otherwise boards assume this is compiled in by default Signed-off-by: Matthew McClintock <msm@freescale.com>
generated by cgit v1.1 at 2024-11-12 21:00:29 +0000