summaryrefslogtreecommitdiff
path: root/drivers/i2c/designware_i2c.c
Commit message (Collapse)AuthorAgeLines
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* designware_i2c: Fixed the setting of the i2c bus speedArmando Visconti2012-12-11-15/+13
| | | | | | | | There are three couple (hcnt/lcnt) of registers for each speed (SS/FS/HS). The driver needs to set the proper couple of regs according to what speed we are setting. Signed-off-by: Armando Visconti <armando.visconti@st.com>
* designware_i2c: Added s/w generation of stop bitArmando Visconti2012-12-11-3/+8
| | | | | | | | | | | | | | | In the newer versions of designware i2c IP there is the possibility of configuring it with IC_EMPTYFIFO_HOLD_MASTER_EN=1, which basically requires the s/w to generate the stop bit condition directly, as the h/w will not automatically generate it when TX_FIFO is empty. To avoid generation of an extra 0x0 byte sent as data, the IC_STOP command must be sent along with the last IC_CMD. This patch always writes bit[9] of ic_data_cmd even in the older versions, assuming that it is a noop there. Signed-off-by: Armando Visconti <armando.visconti@st.com>
* designware_i2c.c: Added the support for MULTI_BUSArmando Visconti2012-12-11-1/+81
| | | | | | | This patch adds the capability to switch between 10 different I2C busses (from 0 to 9). Signed-off-by: Armando Visconti <armando.visconti@st.com>
* i2c: designware_i2c.c: Add support for the "i2c probe" commandStefan Roese2012-07-07-6/+10
| | | | | | | | | | | | | | | i2c_probe() is changed to reinit the i2c bus upon read failure. This is naturally the case upon i2c bus probing. Also, some printf messages upon read failure are removed. As they would interfere with the "i2c probe" command. Additionally, i2c_set_bus_speed() now returns 0, so that the "i2c speed" command can be used. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Amit Virdi <amit.virdi@st.com> Cc: Vipin Kumar <vipin.kumar@st.com>
* i2c:designware Turn off the ctrl when setting the speedArmando Visconti2012-04-24-0/+11
| | | | | | | | | | The designware i2c controller must be turned off before setting the speed in IC_CON register, as stated in the section 6.3.1 of the dw_apb_i2c_db.pdf. Signed-off-by: Michel Sanches <michel.sanches@st.com> Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
* i2c: Add support for designware i2c controllerVipin KUMAR2012-04-24-0/+331
Earlier, a driver exists in the u-boot source for designware i2c interface. That driver was specific to spear platforms. This patch implements the i2c controller as a generic driver which can be used by multiple platforms The driver files are now renamed to designware_i2c.c and designware_i2c.h and these are moved into drivers/i2c folder for reusability by other platforms Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>