summaryrefslogtreecommitdiff
path: root/drivers/ddr/fsl/ctrl_regs.c
Commit message (Collapse)AuthorAgeLines
* powerpc: MPC8555: Remove macro CONFIG_MPC8555York Sun2016-11-23-1/+1
| | | | | | | Replace CONFIG_MPC8555 with ARCH_MPC8555 in Kconfig and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
* powerpc: mpc8541: Remove macro CONFIG_MPC8541York Sun2016-11-23-1/+1
| | | | | | | Replace CONFIG_MPC8541 with ARCH_MPC8541 in Kconfig and clean up existing macros. Signed-off-by: York Sun <york.sun@nxp.com>
* driver/ddr/fsl: Fix timing_cfg_2York Sun2016-08-02-1/+1
| | | | | | | | | Commit 5605dc6 tried to fix wr_lat bit in timing_cfg_2, but the change was wrong. wr_lat has 5 bits with MSB at [13] and lower 4 bits at [9:12], in big-endian convention. Signed-off-by: York Sun <york.sun@nxp.com> Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
* Various, unrelated tree-wide typo fixes.Robert P. J. Day2016-07-16-1/+1
| | | | | | | | | | | | | | | | | | | Fix a number of typos, including: * "compatble" -> "compatible" * "eanbeld" -> "enabled" * "envrionment" -> "environment" * "FTD" -> "FDT" (for "flattened device tree") * "ommitted" -> "omitted" * "overriden" -> "overridden" * "partiton" -> "partition" * "propogate" -> "propagate" * "resourse" -> "resource" * "rest in piece" -> "rest in peace" * "suport" -> "support" * "varible" -> "variable" Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* drivers/ddr/fsl: Fix timing_cfg_2 registerYork Sun2016-06-03-1/+1
| | | | | | | | | Commit 34e026f9 added one extra bit to wr_lat for timing_cfg_2, but with wrong bit position. It is bit 13 in big-endian, or left shift 18 from LSB. This error hasn't had any impact because we don't have fast enough DDR4 using the extra bit so far. Signed-off-by: York Sun <york.sun@nxp.com>
* drivers/ddr/fsl: Update clk_adjust of sdram_clk_cntlShengzhou Liu2016-06-03-2/+9
| | | | | | | | | The clk_adjust is of SDRAM_CLK_CNTL[5:8] 4-bits on MPC85xx and P-series, but is of SDRAM_CLK_CNTL[5:9] 5-bits on T-series and LS-series SoCs. We should update it to adapt the case that clk_adjust is odd data. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* driver/ddr/fsl: Add address parity support for DDR4 UDIMM/discreteShengzhou Liu2016-03-21-5/+50
| | | | | | | | | | Add support of address parity for DDR4 UDIMM or discrete memory. It requires to configurate corresponding MR5[2:0] and TIMING_CFG_7[PAR_LAT]. Parity can be turned on by hwconfig, e.g. hwconfig=fsl_ddr:parity=on. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* driver/ddr/fsl: Update timing config for heavy loadYork Sun2015-12-13-2/+24
| | | | | | | In case four chip-selects are all active, the turnaround times need to increase to avoid overlapping under heavy load. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Update MR5 RTT parkYork Sun2015-12-13-4/+15
| | | | | | For four chip-selects enabled case, RTT is parked on all of them. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Update DDR4 MR6 for Vref rangeYork Sun2015-12-13-0/+3
| | | | | | MR6 bit 6 is set accrodingly for range 1 or 2, per JEDEC spec. Signed-off-by: York Sun <yorksun@freescale.com>
* drivers/ddr/fsl_ddr: Make SR_IE configurableJoakim Tjernlund2015-10-30-1/+1
| | | | | | | | | SR_IE(Self-refresh interrupt enable) is needed for Hardware Based Self-Refresh. Make it configurable and let board code handle the rest. Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Fix driver to support empty first slotYork Sun2015-04-23-21/+43
| | | | | | | | CS0 was not allowed to be empty by u-boot driver in the past to simplify the driver. This may be inconvenient for some debugging. This patch lifts the restrictions. Controller interleaving still requires CS0 populated. Signed-off-by: York Sun <yorksun@freescale.com>
* drivers/ddr/fsl: Update DDR driver for DDR4York Sun2015-04-23-5/+12
| | | | | | | | | | Add/update registers for DDR4, including DQ mappings. Allow raw timing method used for all controllers. Update mode_9 register to 0x500 for improved stability. Check DDR controller version number individually in case a SoC has multiple DDR controllers of different versions. Increase read-write turnaround for DDR4 high speeds. Signed-off-by: York Sun <yorksun@freescale.com>
* MPC8541/MPC8555: Enable SS_EN in DDR_SDRAM_CLK_CNLT registerCurt Brune2015-04-20-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the MPC8555/MPC8541 reference manual the SS_EN (source synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set during initialization. >From section 9.4.1.8 of that manual: Source synchronous enable. This bit field must be set during initialization. See Section 9.6.1, "DDR SDRAM Initialization Sequence," details. 0 - Reserved 1 - The address and command are sent to the DDR SDRAMs source synchronously. In addition, Freescale application note AN2805 is also very clear that this bit must be set. This patch reverts a change introduced by commit 457caecdbca3df21a93abff19eab12dbc61b7897. Testing Done: Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS and inspected the generated assembly code to verify the SS_EN bit was being set. There is one extra instruction emitted: fff9b774: 65 29 80 00 oris r9,r9,32768 Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no additional instructions were emitted related to this patch. Booted an image on a MPC8541 based board successfully. Signed-off-by: Curt Brune <curt@cumulusnetworks.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Fix a typo in timing_cfg_8 calculationYork Sun2015-02-24-1/+1
| | | | | | wwt_bg should match rrt_bg. It was a typo in driver. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Add support for multiple DDR clocksYork Sun2015-02-24-95/+113
| | | | | | | | | Controller number is passed for function calls to support individual DDR clock, depending on SoC implementation. It is backward compatible with exising platforms. Multiple clocks have been verifyed on LS2085A emulator. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Adjust CAS to preamble override for emulatorYork Sun2015-02-24-1/+5
| | | | | | | | | On ZeBu emulator, CAS to preamble overrides need to be set to satisfy the timing. This only impact platforms with CONFIG_EMU. These should be set before MEM_EN is set. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Fix MRC_CYC calculation for DDR3York Sun2014-12-15-1/+20
| | | | | | | | | | For DDR controller version 4.7 or newer, MRC_CYC (mode register set cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD is max(12nCK, 15ns) according to JEDEC spec. DDR4 is not affected by this change. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Adjust timing_cfg_0 to better support two DDR slotsYork Sun2014-12-05-6/+25
| | | | | | | | | Increase write-to-write and read-to-read turnaround time for two-slot DDR configurations. Previously only quad-rank and two dual-rank configurations have this additional turnaround time. A recent test on two single-rank DIMMs shows the shorter additional turnaround time is also needed. Signed-off-by: York Sun <yorksun@freescale.com>
* linux/kernel.h: sync min, max, min3, max3 macros with LinuxMasahiro Yamada2014-11-23-11/+11
| | | | | | | | | | | | | | | | | | | | U-Boot has never cared about the type when we get max/min of two values, but Linux Kernel does. This commit gets min, max, min3, max3 macros synced with the kernel introducing type checks. Many of references of those macros must be fixed to suppress warnings. We have two options: - Use min, max, min3, max3 only when the arguments have the same type (or add casts to the arguments) - Use min_t/max_t instead with the appropriate type for the first argument Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Pavel Machek <pavel@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com> [trini: Fixup arch/blackfin/lib/string.c] Signed-off-by: Tom Rini <trini@ti.com>
* driver/ddr/fsl: Fix DDR4 driverYork Sun2014-09-25-2/+7
| | | | | | | | | | | When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins are not actually connected. Also fix a bug when reading from DDR register to use proper accessor for correct endianess. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Fix tXP and tCKEYork Sun2014-09-25-6/+22
| | | | | | | | The driver was written using old DDR3 spec which only covers low speeds. The value would be suboptimal for higher speeds. Fix both timing according to latest DDR3 spec, remove tCKE as an config option. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Add support of overriding chip select write levelingYork Sun2014-09-08-0/+3
| | | | | | | | | | JEDEC spec allows DRAM vendors to use prime DQ for write leveling. This is not an issue unless some DQ pins are not connected. If a platform uses regular DIMMs but with reduced DDR ECC pins, the prime DQ may end up on those floating pins for the second rank. The workaround is to use a known good chip select for this purpose. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr/freescale: Add support of accumulate ECCYork Sun2014-09-08-0/+5
| | | | | | | | | If less than 8 ECC pins are used for DDR data bus width smaller than 64 bits, the 8-bit ECC code will be transmitted/received across several beats, and it will be used to check 64-bits of data once 8-bits of ECC are accumulated. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr: Fix DDR register timing_cfg_8York Sun2014-07-22-0/+3
| | | | | | | The field wrtord_bg should add 2 clocks if on the fly chop is enabled, according to DDR controller manual for DDR4. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Add workaround for DDR erratum A004508York Sun2014-06-05-0/+5
| | | | | | | | | | | When the DDR controller is initialized below a junction temperature of 0°C and then operated above a junction temperature of 65°C, the DDR controller may cause receive data errors, resulting ECC errors and/or corrupted data. This erratum applies to the following SoCs and their variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023, P2020. Signed-off-by: York Sun <yorksun@freescale.com>
* drivers/ddr: Fix possible out of bounds errorYork Sun2014-04-22-4/+4
| | | | | | | | | This is a theoretical possible out of bounds error in DDR driver. Adding check before using array index. Also change some runtime conditions to pre-compiling conditions. Signed-off-by: York Sun <yorksun@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/ddr/fsl: Add DDR4 support to Freescale DDR driverYork Sun2014-04-22-47/+692
| | | | | | | Mostly reusing DDR3 driver, this patch adds DDR4 SPD handling, register calculation and programming. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr: Add 256 byte interleaving supportYork Sun2014-02-21-0/+1
| | | | | | | Freescale LayerScape SoCs support controller interleaving on 256 byte size. This interleaving is mandoratory. Signed-off-by: York Sun <yorksun@freescale.com>
* driver/ddr: Change Freescale ARM DDR driver to support both big and little ↵York Sun2014-02-21-2/+2
| | | | | | | | | endian Initially it was believed the DDR controller on Freescale ARM would have big endian. But some platform will have little endian. Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/mpc8xxx: Extend DDR registers' fieldsYork Sun2013-11-25-8/+12
| | | | | | | | | | | Some DDR registers' fields have expanded to accommodate larger values. These changes are backward compatible. Some fields are removed for newer DDR controllers. Writing to those fields are safely ignored. TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE automatically. It was a misunderstanding in commit c360ceac. Signed-off-by: York Sun <yorksun@freescale.com>
* Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xxYork Sun2013-11-25-1/+2
| | | | | | | Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3 structure for 83xx, 85xx and 86xx. Signed-off-by: York Sun <yorksun@freescale.com>
* Driver/DDR: Moving Freescale DDR driver to a common driverYork Sun2013-11-25-0/+1657
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs. The similar DDR controllers will be used for ARM-based SoCs. Signed-off-by: York Sun <yorksun@freescale.com>
generated by cgit v1.1 at 2024-11-07 22:40:01 +0000